HiKOKI CR10DL Cordless Electric Reciprocating Saw Instruction Manual

HiKOKI CR10DL Cordless Electric Reciprocating Saw

GENERAL POWER TOOL SAFETY

WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

   • a) Keep work area clean and well lit.
     Cluttered or dark areas invite accidents.

   • b) Do not operate power tools in explosive atmospheres, such as in the presence of fl ammable liquids, gases or dust.
     Power tools create sparks which may ignite the dust or fumes.

   • c) Keep children and bystanders away while operating a power tool.
     Distractions can cause you to lose control.

2. Electrical safety

   • a) Power tool plugs must match the outlet.
     Never modify the plug in any way.
     Do not use any adapter plugs with earthed (grounded) power tools.
     Unmodifi ed plugs and matching outlets will reduce risk of electric shock.

   • b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
     There is an increased risk of electric shock if your body is earthed or grounded.

   • c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

   • d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
     Damaged or entangled cords increase the risk of electric shock.

   • e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
     Use of a cord suitable for outdoor use reduces the risk of electric shock.

   • f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
     Use of an RCD reduces the risk of electric shock.

3. Personal safety

   • a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the infl uence of drugs, alcohol or medication.
     A moment of inattention while operating power tools may result in serious personal injury.

   • b) Use personal protective equipment. Always wear eye protection.
     Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

   • c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your fi nger on the switch or energising power tools that have the switch on invites accidents.

   • d) Remove any adjusting key or wrench before turning the power tool on.
     A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

   • e) Do not overreach. Keep proper footing and balance at all times.
     This enables better control of the power tool in unexpected situations.

   • f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
     Loose clothes, jewellery or long hair can be caught in moving parts.

   • g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
     Use of dust collection can reduce dust-related hazards.

   • h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
     A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care

   • a) Do not force the power tool. Use the correct power tool for your application.
     The correct power tool will do the job better and safer at the rate for which it was designed.

   • b) Do not use the power tool if the switch does not turn it on and off .
     Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

   • c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

   • d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
     Power tools are dangerous in the hands of untrained users.

   • e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may aff ect the power toolʼs operation.
     If damaged, have the power tool repaired before use.
     Many accidents are caused by poorly maintained power tools.

   • f) Keep cutting tools sharp and clean.
     Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

   • g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
     Use of the power tool for operations different from those intended could result in a hazardous situation.
     h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
     Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Service

6. a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
   This will ensure that the safety of the power tool is maintained.

PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children and infi rm persons.

TOOLS

CORDLESS RECIPROCATING SAW

SAFETY WARNINGS

1. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring.
   Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

2. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.

ADDITIONAL SAFETY WARNINGS

1. Do not allow foreign matter to enter the hole for connecting the rechargeable battery.

2. Never disassemble the rechargeable battery and charger.

3. Never short-circuit the rechargeable battery. Shortcircuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery.

4. Do not dispose of the battery in fi re. If the battery is burnt, it may explode.

5. When cutting in wall, floor or ceiling, check for buried electric power cord, etc.

6. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery.

7. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or infl ammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger.

8. When using this unit continuously, the unit may overheat, leading to damage in the motor and switch. Please leave it without using it for approximately 15 minutes.

9. Wear earplugs to protect your ears during operation.

10. Do not touch the blade during or immediately after operation. The blade becomes very hot during operation and could cause serious burns.

11. Always hold the housing of the power tool fi rmly as shown in Fig. 9 and Fig. 10. Otherwise the counterforce produced may result in inaccurate and even dangerous operation.

12. Remove the battery from tool or place the switch in the locked or off position before making any adjustments, changing accessories, storing, carrying, or when not using the tools.

13. Mounting and dismounting the blade

    • Be absolutely sure to keep the switch turned off and the battery removed to prevent any accident.

    • Pull the back of the saw blade two or three times by hand and check that the blade is securely mounted. When pulling the blade, you will know it is properly mounted if it clicks and the lever moves slightly. (Fig. 3)

    • When pulling the saw blade, be absolutely sure to pull it from the back. Pulling other parts of the blade will result in an injury.

    • If the broken saw blade is hidden inside the small slit, hook the broken blade using a tip of another saw blade and take it out. (Fig. 4)

    • After use, blow away sawdust, earth, sand, moisture, etc., with air or brush them away with a brush, etc., to ensure that the blade mount can function smoothly.

    • As shown in Fig. 5, carry out lubrication around the blade holder on a periodic basis by use of cutting fluid, etc.

    • Continued use of the tool without cleaning and lubricating the area where the saw blade is installed can result in some slack movement of the lever due to accumulated sawdust and chips. Under the circumstances, pull a rubber cap provided on the lever in the direction of an arrow mark as shown in Fig. 5 and remove the rubber cap from the lever. Then, clean up the inside of the blade holder with air and the like and carry out suffi cient lubrication.
      The rubber cap can be fitted on if it is pressed firmly onto the lever. At this time, make certain that there exists no clearance between the blade holder and the rubber cap, and furthermore ensure that the saw-blade-installed area can function smoothly.

    • Do not use any saw blade with a worn-out blade hole. Otherwise, the saw blade can come off , resulting in personal injury.

14. When setting the base position, be absolutely sure to keep the switch turned off and the battery removed to prevent any accident.

15. Make sure that the battery is installed firmly. If it is at all loose it could come off and cause an accident.

16. Do not carry tools with your finger on the switch. A sudden startup can result in an unexpected injury.

17. Be careful not to let sawdust, earth, moisture, etc., enter the inside of the machine through the plunger section during operation. If sawdust and the like accumulate in the plunger section, always clean it before use.

18. During use, press the base firmly against the workpiece.

19. Select a saw blade of the most appropriate length. Ideally, the length protruding from the base of the saw blade after subtracting the stroke quantity should be larger than the material.
    If you cut a large pipe, large block of wood, etc., that exceeds the cutting capacity of a blade; there is a risk that the blade may contact with the inner wall of the pipe, wood, etc., resulting in damage. (Fig. 8)

20. Never apply any unreasonable force to the saw blade when cutting. Doing so can easily break the blade.

21. The motor can be locked sometimes, depending on the combination of the material to be cut and the blade. Whenever the motor gets locked, switch it off immediately.

22. Fasten a workpiece fi rmly before operation. (Fig. 9)

23. When cutting metallic materials, use proper machine oil (turbine oil, etc.). When not using liquid machine oil, apply grease over the workpiece.
    The service life of the saw blade will be drastically shortened if you don’t use machine oil.

24. Delay the feed speed when cutting the material into small circular arcs. An unreasonably fast feed may break the blade.

25. Avoid plunge cutting for metallic materials. This can easily damage the blade.

26. Never pull the switch trigger while the tip of the saw blade tip is pressed against the material. If you do so, the blade can easily be damaged when it collides with the material.

27. Make absolutely sure that you cut slowly while holding the body firmly. If you apply any unreasonable force to the saw blade during the cutting operation, the blade can easily be damaged.

28. The use of the battery in a cold condition (below 0 degree Centigrade) can sometimes result in the weakened cutting torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up.

29. Do not look directly into the light. Such actions could result in eye injury.

30. The level at which the battery level warning lamp lights may vary due to the ambient temperature, characteristics of the battery, etc. and is intended only as a guide.

31. The battery level warning lamp may light when the power tool is overloaded. This does not mean that the battery power is very low.
    Be sure to check the battery level while the tool is in a no-load state.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output.
In the cases of 1 to 3 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function.

1. When the battery power remaining runs out, the motor stops.
   In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the battery power may stop.
   In this case, stop using the battery and let the battery cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING
In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the battery.
   • During work make sure that swarf and dust do not fall on the battery.
   • Make sure that any swarf and dust falling on the power tool during work do not collect on the battery.
   • Do not store an unused battery in a location exposed to swarf and dust.
   • Before storing a battery, remove any swarf and dust that may adhere to it and do not store it together with metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a nail, strike with a hammer, step on, throw or subject the battery to severe physical shock.
3. Do not use an apparently damaged or deformed battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car cigarette lighter sockets.
6. Do not use the battery for a purpose other than those specifi ed.
7. If the battery charging fails to complete even when a specifi ed recharging time has elapsed, immediately stop further recharging.
8. Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container.
9. Keep away from fi re immediately when leakage or foul odor are detected.
10. Do not use in a location where strong static electricity generates.
11. If there is battery leakage, foul odor, heat generated, discolored or deformed, or in any way appears abnormal during use, recharging or storage, immediately remove it from the equipment or battery charger, and stop use.
12. Do not immerse the battery or allow any fluids to fl ow inside. Conductive liquid ingress, such as water, can cause damage resulting in fi re or explosion. Store your battery in a cool, dry place, away from combustible and fl ammable items. Corrosive gas atmospheres must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately.
   If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately.
   There is a possibility that this can cause skin irritation.

3. If you fi nd rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the fi rst time, do not use and return it to your supplier or vendor.

WARNING
If a conductive foreign matter enters in the terminal of lithium ion battery, the battery may be shorted, causing fi re. When storing the lithium ion battery, obey surely the rules of following contents.

• Do not place conductive debris, nail and wires such as iron wire and copper wire in the storage case.
• To prevent shorting from occurring, load the battery in the tool or insert securely the battery cover for storing until the ventilator is not seen.

SYMBOLS

WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the accessories listed on page 160.
Standard accessories are subject to change without notice.

APPLICATIONS

• Cutting pipe and angle steel.
• Cutting various lumbers.
• Cutting mild steel plates and aluminum plates.
• Cutting synthetic resins, such as phenol resin and vinyl chloride.

SPECIFICATIONS

Capacity

| Mild Steel Pipe| O.D. 25 mm
Vinyl Chloride Pipe| O.D. 45 mm
Wood| Depth 50 mm
Mild Steel Plate| Thickness 4 mm
Weight*| 1.2 – 1.4 kg (BCL1015)

• According to EPTA-Procedure 01/2014.

NOTE
Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the receptacle.
   When connecting the plug of the charger to a receptacle, the pilot lamp will blink in red (At 1- second intervals).
   CAUTION
   Do not use the electrical cord if damaged. Have it repaired immediately.

2. Insert the battery into the charger. (Fig. 2) Firmly insert the battery into the charger till it contacts the bottom of the charger.

3. Charging
   When inserting a battery in the charger, charging will commence and the pilot lamp will light continuously in red.
   When the battery becomes fully recharged, the pilot lamp will blink in red. (At 1-second intervals) (See Table 1)

   • Pilot lamp indication
     The indications of the pilot lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.
     Table 1

   • Regarding the temperatures and charging time of the battery.
     The temperatures and charging time will become as shown in Table 2.
     Table 2**** Charger

Battery

| UC10SL2
---|---
Charging voltage| V| 10.8
Weight| kg| 0.35
Type of battery| Li-ion
Temperatures at which the battery can be recharged| 0oC – 50oC
Charging time for battery capacity, approx. (At 20oC)| ****

25 (3 cells)

30 (3 cells)

60 (6 cells)

1.3 Ah

1.5 Ah

3.0 Ah

| min. min. min.

NOTE
The recharging time may vary according to the ambient temperature and power source voltage.

4. Disconnect the charger’s power cord from the receptacle.
5. Hold the charger fi rmly and pull out the battery.
   NOTE
   Be sure to pull out the battery from the charger after use, and then keep it.

CAUTION

• If the battery is charged while it is heated because it has been left for a long time in a location subject to direct sunlight or because the battery has just been used, the pilot lamp of the charger lights for 1 second, does not light for 0.5 seconds (off for 0.5 seconds). In such a case, fi rst let the battery cool, then start charging.
• When the pilot lamp fl ickers (at 0.2-second intervals), check for and take out any foreign objects in the charger’s battery connector. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.
• Since the built-in micro computer takes about 3 seconds to confi rm that the battery being charged with charger is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged.

MOUNTING AND OPERATION

Battery level warning lamp (Indicates that the battery level is low and requires recharging.)|

12

| 163
Selecting accessories| ―| 164

SELECTION OF BLADES

To ensure maximum operating effi ciency and results, it is very important to select the appropriate blade best suited to the type and thickness of the material to be cut.
The blade number is engraved in the vicinity of the mounting portion of each blade. Select appropriate blades by referring to Table 3-5.
Table 3: HCS blades

Table 4: Bl-METAL blades

Table 5: Selection of blades for other materials

103, 109

Below 3.5| No. 3, 107
Nonferrous metal| Aluminium, Copper and Brass| 5 – 20| No. 2, 101,

103, 109

Below 5| No. 3, 107
Synthetic resin| Phenol resin, Melamine resin, etc.| 10 – 50| No. 2, 4, 101,

103

5 – 30| No. 3, 5, 8,

107,109

Vinyl chloride, Acrylic resin, etc.| 10 – 60| No. 2, 4, 101,

103

5 – 30| No. 3, 5, 8,

107, 109

MAINTENANCE AND INSPECTION

CAUTION
Be sure to turned off the switch and remove the battery before maintenance and inspection.

1. Inspecting the blade
   Continued use of a dull or damaged blade will result in reduced cutting e fficiency and may cause overloading of the motor. Replace the blade with a new one as soon as excessive abrasion is noted.

2. Inspecting the mounting screws
   Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard.

3. Maintenance of the motor
   The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

4. Cleaning on the outside
   When the power tool is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics.

5. Storage
   Store the power tool in a place in which the temperature is less than 40°C and out of reach of children.
   Storing lithium-ion batteries.
   Make sure the lithium-ion batteries have been fully charged before storing them.
   Prolonged storage (3 months or more) of batteries with a low charge may result in performance deterioration, signifi cantly reducing battery usage time or rendering the batteries incapable of holding a charge.
   However, signifi cantly reduced battery usage time may be recovered by repeatedly charging and using the batteries two to fi ve times.
   If the battery usage time is extremely short despite repeated charging and use, consider the batteries dead and purchase new batteries.

CAUTION
In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with statutory/country specifi c regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a HiKOKI Authorized Service Center.

IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance with the following code:
Blue: — Neutral
Brown: — Live
As the colours of the wires in the main lead of this tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal.

NOTE
This requirement is provided according to BRITISH STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration The measured values were determined according to EN62841 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 102 dB (A) Measured A-weighted sound pressure level: 91 dB (A) Uncertainty K: 5 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined according to EN62841.
Cutting boards:
Vibration emission value ah, B = 19.7 m/s2
Uncertainty K = 1.5 m/s2
Cutting wooden beams:
Vibration emission value ah, WB = 24.9 m/s2 Uncertainty K = 1.6 m/s2

The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.

WARNING

• The vibration emission during actual use of the power tool can diff er from the declared total value depending in the ways in which the tool is used.
• Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

NOTE
Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.

GUARANTEE CERTIFICATE

1. Model No.
2. Serial No.
3. Date of Purchase
4. Customer Name and Address
5. Dealer Name and Address
   (Please stamp dealer name and address)

Hikoki Power Tools Deutschland GmbH
Siemensring 34, 47877 willich, Germany
Tel: +49 2154 49930
Fax: +49 2154 499350
URL: http://www.hikoki-powertools.de
Hikoki Power Tools Netherlands B.V.
Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands Tel: +31 30 6084040
Fax: +31 30 6067266
URL: http://www.hikoki-powertools.nl
Hikoki Power Tools (U.K.) Ltd.
Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom
Tel: +44 1908 660663
Fax: +44 1908 606642
URL: http://www.hikoki-powertools.uk
Hikoki Power Tools France S.A.S.
Parc de l’Eglantier 22, rue des Cerisiers, Lisses-C.E. 1541, 91015 EVRY CEDEX, France
Tel: +33 1 69474949
Fax: +33 1 60861416
URL: http://www.hikoki-powertools.fr
Hikoki Power Tools Belgium N.V./S.A.
Koningin Astridlaan 51, B-1780 Wemmel, Belgium
Tel: +32 2 460 1720
Fax: +32 2 460 2542
URL http://www.hikoki-powertools.be
Hikoki Power Tools Italia S.p.A
Via Piave 35, 36077, Altavilla Vicentina (VI), Italy
Tel: +39 0444 548111
Fax: +39 0444 548110
URL: http://www.hikoki-powertools.it
Hikoki Power Tools lbérica, S.A.
C/ Puigbarral, 26-28, Pol. Ind. Can Petit, 08227 Terrassa (Barcelona), Spain
Tel: +34 93 735 6722
Fax: +34 93 735 7442
URL: http://www.hikoki-powertools.es
Hikoki Power Tools Österreich GmbH
IndustrieZentrum NÖ –Süd, Straße 7, Obj. 58/A6 2355 Wiener Neudorf, Austria
Tel: +43 2236 64673/5
Fax: +43 2236 63373
URL: http://www.hikoki-powertools.at
Hikoki Power Tools Norway AS
Kjeller Vest 7, N-2007 Kjeller, Norway
Tel: (+47) 6692 6600
Fax: (+47) 6692 6650
URL: http://www.hikoki-powertools.de
Hikoki Power Tools Sweden AB
Rotebergsvagen 2B SE-192 78 Sollentuna, Sweden
Tel: (+46) 8 598 999 00
Fax: (+46) 8 598 999 40
URL: http://www.hikoki-powertools.se
Hikoki Power Tools Denmark A/S
Lillebaeltsvej 90, 6715 Esbjerg N, Denmark
Tel: (+45) 75 14 32 00
Fax: (+45) 75 14 36 66
URL: http://www.hikoki-powertools.dk
Hikoki Power Tools Finland Oy
Tupalankatu 9, 15680 Lahti, Finland
Tel: (+358) 20 7431 530
Fax: (+358) 20 7431 531
URL: http://www.hikoki-powertools.fi
Hikoki Power Tools Hungary Kft.
1106 Bogáncsvirág u.5-7, Budapest, Hungary
Tel: +36 1 2643433
Fax: +36 1 2643429
URL: http://www.hikoki-powertools.hu
Hikoki Power Tools Polska Sp. z o. o.
ul. Gierdziejewskiego 1
02-495 Warszawa, Poland
Tel: +48 22 863 33 78
Fax: +48 22 863 33 82
URL: http://www.hikoki-narzedzia.pl
Hikoki Power Tools Czech s.r.o.
Modřická 205, 664 48 Moravany, Czech Republic
Tel: +420 547 422 660
Fax: +420 547 213 588
URL: http://www.hikoki-powertools.cz
Hikoki Power Tools Romania S.R.L.
Ring Road, No. 66, Mustang Traco Warehouses, Warehouse No.1, Pantelimon City, 077145, Ilfov County, Romania
Tel: +40 371 135 109
Fax: +40 372 899 765
URL: http://www.hikoki-powertools.ro

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that Reciprocating Saw, identifi ed by type and specifi c identifi cation code 1), is in conformity with all relevant requirements of the directives 2) and standards 3). Technical fi le at 4) – See below.
The European Standard Manager at the representative offi ce in Europe is authorized to compile the technical fi le.
The declaration is applicable to the product affi xed CE marking.

1. CR13V2 C338589S

2. 2006/42/EC, 2014/30/EU, 2011/65/EU

3. EN62841-1:2015
   EN62841-2-11:2016+A1:2020
   EN55014-1:2006+A1:2009+A2:2011
   EN55014-2:1997+A1:2001+A2:2008
   EN61000-3-2:2014
   EN61000-3-3:2013

4. Representative offi ce in Europe

Hikoki Power Tools Deutschland GmbH
Siemensring 34, 47877 Willich, Germany
Head offi ce in Japan
Koki Holdings Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>