TAURUS-8T4 Transmitter Remote Control Base Module User Guide

TAURUS-8T4 Transmitter Remote Control Base Module

Operation

Press any of the switches to operate.
The Transmitter will auto sleep between operations to save power.
RF Transmit GREEN LED operates when Taurus is transmitting an RF signal.
RF Acknowledge (if configured):
GREEN LED will Flash at high speed to indicate that an acknowledgment has successfully been received back form the receiver.
RED LED will Flash at high speed to indicate that an acknowledgment has not been received back form the receiver.
Low Battery: If battery requires recharging Low Battery LED illuminates for 3 seconds after each operation.

Recharging the Battery

Recharge with either USB Cable or QI Wireless Charger

When Charging the Battery RED LED gives a slow Flash indicates charging is in progress.
When fully charged the GREEN LED is illuminated
Note: If the Battery becomes very depleted it can take a few minutes before there is adequate charge to start the RED LED to flash!

Configuring Modes of Operation

To configure the modes of operation, unscrew the six enclosure fixing screws to access the internal circuit board.
The SET switch is used to configure the operating modes.

The Following Modes can be configured using the SET Switch

1. RF Mode of Transmission (FM or LORA Mode)
2. Acknowledgment back from the Receiver
3. Automatic Watchdog Transmissions
4. Continuous or State Change Transmission

TAURUS Transmitters are factory Shipped with the following Settings

Restoring TAURUS to Factory Default

To Set the RF Transmission MODE

This sets the type of RF Transmission.
Possible options are FM, or LORA Modes 0 – 7
FM or LORA mode 0 provides the quickest response; from Transmitter sw pressed to Receiver Relay output.
LORA mode 7 provides the longest operating range but with the longest time delay of from button press to receiver relay actuation.

Notes

1. Range is dependant on many factors including the mode of transmission. Range can be reduced by 75% in built up areas with poor antenna, and environmental conditions.
2. Battery life quoted is approximate based on 30 operations per day.

RF Transmission

| Mode

(No of LED1 Flashes)

| Propagation Time

from TX to output Activated (approx)

| Operations from a Single battery charge
---|---|---|---
FM| 1| 20 mS| 1Million
LoRa Mode 1| 2| 20 mS| ~550K
LoRa Mode 2| 3| 40 mS| 288K
LoRa Mode 3| 4| 80 mS| 144K
LoRa Mode 4| 5| 160 mS| 72K
LoRa Mode 5| 6| 320 mS| 36K
LoRa Mode 6| 7| 640 mS| 18K
LoRa Mode 7| 8| 1.28 Secs| ~9,000

To Set Continuous or State Change RF Transmissions

When a switch button is operated, TAURUS will transmit a “Button Down” RF Transmission.
When a switch button is released, TAURUS will transmit a “Button Up” RF Transmission.

Continuous Transmit
TAURUS repeat transmits “button Down” in short bursts for as long as switch button is pressed.
If the Acknowledgment is ON the receiver will reply after each RF transmission burst.
This is ideally suited to momentary operation where the receiver output needs to be active as long as the user presses down a TAURUS Button.

State Change Transmit
TAURUS transmits an RF transmission only when the switch button is pressed or released (i.e. a state change).
On each of these “state changes” TAURUS transmits up to 4 transmissions, or, “RF packets” (which can be seen by the GREEN LED flashing up to 4 times,
If the Acknowledgment is ON the receiver will reply immediately.
After receiving an Acknowledgment the TAURUS will cease sending any remaining of the 4 transmissions.

LED Status

Continuous Transmission

Acknowledgement OFF

Operation| GREEN LED| RED LED
Button is briefly pressed| Flashes briefly| No-operation
Button is held Down| Flashes constantly| No-operation
Button is released| Flashes briefly| No-operation
Continuous Transmission Acknowledgement ON

Operation| GREEN LED| RED LED
Button is briefly pressed| Flashes briefly (TX then RX ack)| Flashes if no Ack received
Button is held Down| Flashes continually (TX then RX ack)| Flashes if no Ack received
Button is released| Flashes briefly (TX then RX ack)| Flashes if no Ack received
State Change Transmission Acknowledgement OFF

Operation| GREEN LED| RED LED
Button is briefly pressed| Flashes 1X (TX)| No-operation
Button is held Down| No-operation| No-operation
Button is released| Flashes 1X (TX)| No-operation
State Change Transmission Acknowledgement ON

Operation| GREEN LED| RED LED
Button is briefly pressed

& Receiver, ack OK

|

Flashes (TX then RX ack)

|

No-operation

Button is briefly pressed

& Receiver, NOK

|

Flashes continually (awaiting Ack)

|

Flashes to show no Ack received

Button is held Down| Flashes continually (awaiting Ack)| Flashes to show no Ack received
Button is released| Flashes 2 – 5X (TX and RX ack)| Flashes if no Ack received

To Set Acknowledgement Request

Acknowledgement Feature provides the user with LED indication that the receiver has successfully received the transmitters signal.
When activated the TAURUS Transmitter includes an acknowledgement request within each radio transmission.
The response from the receiver is indicated on the transmitter via the RED / GREEN LEDs.

RF Acknowledgment from Receiver – Warning! When Acknowledgement is ON, TAURUS requests an RF signal back from the receiver. Whilst in theory if an RF signal can be transmitted one way then it can be returned, in practice occasionally the received acknowledgement many not penetrate as well as the Taurus transmitted signal.

To Set Watchdog Transmissions

If enabled, TAURUS automatically transmits a background “watchdog” RF Signal approx. every
~45 secs,
RF Solutions Receivers with a Watchdog feature will hold a Relay contact “ENERGISED” as long as Watchdog is regularly received confirming the transmitter is in range and the system is operating correctly.
When using Watchdog it may be useful to incorporate a Power Switch to avoid premature battery discharge.
A power switch can be incorporated if this is required please contact our Sales Dept.

Simplified Declaration of Conformity (RED)

Hereby, RF Solutions Limited declares that the radio equipment type defined within this document is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.rfsolutions.co.uk

RF Solutions Ltd. Recycling Notice
Meets the following EC Directives:
DO NOT Discard with normal waste, please recycle.
ROHS Directive 2011/65/EU and amendment 2015/863/EU
Specifies certain limits for hazardous substances.
WEEE Directive 2012/19/EU
Waste electrical & electronic equipment. This product must be disposed of through a licensed WEEE collection point. RF Solutions Ltd., fulfils its WEEE obligations by membership of an approved compliance scheme.
Environment Agency producer registration number: WEE/JB0104WV.

Waste Batteries and Accumulators Directive 2006/66/EC
Where batteries are fitted, before recycling the product, the batteries must be removed and disposed of at a licensed collection point.
RF Solutions battery producer number: BPRN00060.

Disclaimer:
Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever for its accuracy, adequacy or completeness. No express or implied warranty or representation is given relating to the information contained in this document. RF Solutions Ltd reserves the right to make changes and improvements to the product(s) described herein without notice. Buyers and other users should determine for themselves the suitability of any such information or products for their own particular requirements or specification(s). RF Solutions Ltd shall not be liable for any loss or damage caused as a result of user’s own determina-tion of how to deploy or use RF Solutions Ltd’s products. Use of RF Solutions Ltd products or components in life support and/or safety applications is not authorised except with express written approval. No licences are created, implicitly or otherwise, under any of RF Solutions Ltd’s intellectual property rights. Liability for loss or damage result-ing or caused by reliance on the information contained herein or from the use of the product (including liability resulting from negligence or where RF Solutions Ltd was
aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict RF Solutions Ltd’s liability for death or personal injury

References

• ons.co.uk
• RF Solutions | Remote control systems, RF Modules, Antennas
• RF Solutions | Remote control systems, RF Modules, Antennas
• rtsintercom.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>