ZKTeco KBRZ09 Smart Lock Installation Guide
- June 10, 2024
- ZKTECO
Table of Contents
ZKTeco KBRZ09 Smart Lock
Product Information
KBRZ09 Smart Lock
The KBRZ09 Smart Lock is an electronic door lock that allows for keyless entry. It comes with installation instruction and user guide manual.
The product complies with part 15 of the FCC Rules and Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). It contains a licence- exempt transmitter(s)/receiver(s) that comply with the regulations. The device should be installed and operated with a minimum distance of 20cm between the radiator and the user’s body.
Product Usage Instructions
Before using the KBRZ09 Smart Lock, please read the installation instruction and user guide manual carefully.
- Install the lock following the instructions provided in the manual.
- To lock the door, press the lock button on the outside of the door. To unlock the door, enter the correct code on the keypad or use a remote control (if provided).
- If the lock battery is low, replace it with a new one following the instructions in the manual.
- Do not modify or change any parts of the lock as it may void your authority to operate the equipment.
- Keep a distance of at least 20cm between your body and the lock’s radiator when installing or operating it.
TOOL REQUIRED:
Do not use an electric screwdriver during installation.
INSTALLATION INSTRUCTION
Parts List
If any parts are missing or damaged, please contact Customer Support.
ASSEMBLY
STEP 1
Prepare the door and check dimensions
- A. Measure to confirm that the hole in the door is 2-1/8″ (54mm) Measure to confirm that the hole in the door edge is 1″ (25mm).
- B. Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)
- C. Measure to confirm that the door is 1-3/8″ to 2″ (35mm to 50mm) thick.
- D. Make sure the hole in the door frame is drilled a minimum of 1″ (25mm) deep, to leave enough space for the latch to extend into the door frame when the door is locked.
Notes: Make sure the door frame is aligned with the door. There are no obstructions stuck in the door frame.
STEP 2
Install the latch and strike
-
A. Latch backset adjustment
Backset is the distance from the door edge to the center of the hole in the door. The latch is provided with adjustable design which can fit either 2-3/8″(60mm) or 2-3/4″(70mm) backset.
If the backset of your door is 2-3/8″(60mm), no need to adjust the latch.
If the backset of your door is 2-3/4″(70mm), please adjust the latch. -
B. Install the latch
-
C. Install strike on the door frame.
IMPORTANT:
Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep. -
D. Change Handle Direction (Optional)
Notes: The handle direction can be chan ed for com atible with both right handed and left handed doors.
Change the Handle direction of exterior assembly.
Loosen the reversing screw by using a screwdriver. Rotate the lever to the other end and keep it horizontal. Tighten the reversing screw.
Change the Handle direction of interior assembly.
Loosen the screw completely and remove the screw by using a screwdriver. Rotate the handle to the other side and keep the handle horizontal. Tighten the screw in the Left-hand or Right-hand screw holes according to the actual handle direction.
STEP 3
Install exterior assembly
- A. Route the cable below the latch, and insert the torque blade through the slot in the latch.
- B. Secure the mounting plate with the supplied screws.
Do not overtighten screws.
STEP 4
Install interior assembly
-
A. Push the battery cover out in the direction as illustrated.
IMPORTANT: Do not load batteries until lock is completely installed. -
B. Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.
-
C. Attach Interior Assembly to Mounting Plate and tighten 3 Screws.
-
D. Insert 4 AA Alkaline batteries and put on the battery cover.
At a Glance
How to Lock/ Unlock
UNLOCK the door from outside
LOCK the door from outside
UNLOCK the door from inside
LOCK the door from inside
Auto Lock Mode
In Auto Lock Mode,the lock will automatically move to locked position after 5
seconds, then the lever can’t be turned.
Tap and hold Lock icon in App to lock.
Definitions
-
Master Code
Required for programming user codes, fingerprints and IC card. The default master code needs to be changed before programming.
After pairing DDLock App successfully, the master code will be changed to a random 7 digit number, and you can change ii to your own master code in App. -
Auto Lock & One-touch Lock
Automatically locks the latch after the door closed in 5 seconds. Auto Lock is disabled by default. The Auto Lock time can be customized between 1 and 900 seconds.
One-touch Lock is pressing and holding “#” on the touch keypad for 2 seconds to lock from outside. -
Wrong Entry Limit
After 5 times unsuccessful attempts at entering an invalid password, the device will shut down for 2 minutes. -
Passage Mode
Move the Passage Switch to enable and disable the Passage Mode.
Enable Passage Mode, the lock will stay Unlocked until it’s locked manually.
In Passage Mode, Auto-lock will be disabled. -
Anti-peeping password
Entering random numbers before or after correct password will also unlock the door, which can prevent the password being exposed.The length of anti-peeping password should be within 16 digits.
Programming Guide
IMPORTANT:
The default Master Code isl 2 5 6
It is required that you change it to a code of your own before programming.
Factory Default Settings
How to Reset?
Press and hold the Reset button on the interior assembly for 5 seconds by
using the Reset tool, until you hear a short beep and Green light flashes
once.
IMPORTANT
The Reset Button must be turned on in DDLock App before resetting.
DDLOCK GUIDE
HOW TO REGISTER
STEP 1
Download “DDLock” App in Google Play or App Store.
STEP 2
STEP 3
Fill out the information and tap “Get Code”
The email inbox you registered will be sent a verification code to verify your
account.
Put the code you received, tap on “Register” to complete.
Notes:
The DDLock App is required to operate the lock.
After the lock is properly installed, make sure this step is performed by the
lock owner.
Pairing Your Lock
Notes:
You may need to touch the keypad screen to wake up the keypad.
Admin Passcode Management
After pairing the lock with DDLock, the admin passcode will be changed to a random 7 digit number, you can check the new admin passcode by following the picture guide on left. And you can change it to your own administrator password.
Lock Page Overview
Unlock/Lock
Unlock/Lock using phone’s bluetooth
Passcode
Generate 6 different types of passcodes
eKey Page
View and modify current eKeys
Settings Page
View and modify settings
Authorized Admin Page
Create and edit admins
Cards
Set up your cards here
Notes: Some of these icons may not appear if the Gateway is not connected to the lock.
APP Unlock/ Lock
To unlock the lock, tap this icon once.
To lock the lock, press and hold on this icon.
Passcode
IC Card
STEP 3
Choose the validity period of the lock Once the lock says “Please swipe your
card”, place the card against 5 on the keypad
If you hear a long beep, the card can be used to unlock your lock
Fingerprints
STEP 1
eKeys work by sharing app access of your lock with another DDLock account.
eKey recipients will be able to use their phone to unlock/lock the lock.
STEP 2
Tap on “Send eKey'”_
STEP 3
Enter recipient’s username. It will be the phone number or email address
during registration. eKeys do not require wifi or bluetooth to be sent or
revoked.
Authorized Admin
Authorized Admin is similar to eKeys_ However, the Authorized Ad min also have
the following accesses.
STEP 1
- Unlock/lock via the app.
- Generate, Edit, Delete passcodes, IC cards, & fingerprints.
- Adjust settings like passage mode, auto-lock timer, & turn on/off the lock sound.
STEP 2
Tap on “Authorized Admin” Set Timed Admin or Permanent Admin.
Passage Mode & Auto-Lock
STEP 1
Enable Auto Lock, the lock will be locked automatically in 5 seconds by
default.
The Auto Lock time can be changed in Auto Lock timer.
Go to Settings as shown in the image to get more information regarding Auto
Lock.
STEP 2
Settings > Passage Mode
STEP 3
Enable Passage Mode, the lock will stay Unlocked until it’s locked manually.
In Passage Mode, Auto-lock will be disabled.
Lock Settings
- In Basics , you can view and change lock information such as Lock Name.
- Gatewa shows signal strength if Gateway is connected.
- With Remote Unlock and a Gateway connected, you can remotely unlock/lock your lock.
- Lock Sound turns on or off the sound of the touch keypad.
- Import from another lock allows for the transfer of passcodes and cards from one lock to another.
- Delete will remove the lock from your account and clear any settings on the lock. It requires your phone close to the lock.
Troubleshooting
Why the lock won’t accept any inputs after I entered a code or fingerprint
incorrectly for so many times?
The lock will shut down for 2 minutes after 5 unsuccessful attempts at
entering an invalid code or fingerprint.
You can unlock the lock once in the App or wait 2 minutes to continue.
How do I lock manually from outside?
Press and hold # to lock the lock from outside.
The batteries are completely dead before I replace new batteries.
When the batteries are completely dead, the physical keys are available to
unlock.
How do I share access of the lock to my family members?
Go to DDLock App, in eKeys or Authorized Admin, it can share access of the
lock to your family.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
Information & Safety Warnings
- Protect your User Codes and Master Code.
- Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
- Do not use an electric screwdriver during installation.
- This manufacturer advises that no lock can provide complete security by itself.
- This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property
- No lock can substitute for caution, awareness of your environment, and common sense.
- Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing
- The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
- Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>