AEG LWR9516BN4 Washer Dryer User Manual

LWR9516BN4 Washer Dryer

Product Information

The LWR9516BN4 is a washer dryer from AEG. It has a worktop,
detergent dispenser, air filter(s), control panel, door handle,
drain pump filter, feet for leveling the appliance, airflow slots,
water drain hose, water inlet valve, mains cable, transit bolts,
and hose supports. The rating plate reports the model name, product
number, electrical ratings, and serial number. The appliance has a
width of 59.7 cm, height of 87.0 cm, and total depth of 66.0 cm. It
requires a voltage of 230V, overall power of 2200W, fuse of 10A,
and frequency of 50Hz. The level of protection against ingress of
solid particles and moisture is ensured by the protective cover,
except where the low voltage equipment has no protection against
moisture (IPX4). The maximum wash load for cotton is 10 kg,
synthetics is 4 kg, and wool is 1.5 kg. The maximum dry load for
cotton is 6 kg, synthetics is 4 kg, and wool is 1 kg. The maximum
spin speed is 1551 rpm. The product contains HFC – R134a/GWP1430
0.14 kg fluorinated gas hermetically sealed.

Product Usage Instructions

Before beginning the installation and use of this appliance,
carefully read the supplied instructions. The manufacturer is not
responsible for any injuries or damage that are the result of
incorrect installation or usage. Always keep the instructions in a
safe and accessible location for future reference.

Safety Information

Refer to the safety chapters before installing the appliance.
Children and vulnerable people safety must be taken into
consideration when using this appliance.

Installation

The installation must comply with relevant national regulations.
Unpack the appliance and remove all the packaging and the transit
bolts before installing the appliance. As you will put down the
appliance on the rear side, wait about 6 hours before you use it.
This time is necessary to enable the compressor to work
properly.

Electrical Connection

Ensure that the electrical connection complies with the relevant
national regulations. There is a risk of fire and electric shock if
not done properly.

Water Connection

Connect the water inlet hose to a water tap with a 3/4” thread.
Ensure that the water supply pressure is between 0.5 bar (0.05 MPa)
and 10 bar (1.0 MPa).

Use

Follow the instructions carefully to avoid any risk of injury,
electric shock, fire, burns, or damage to the appliance. Always use
original spare parts. When contacting the authorized service
center, ensure that you have the following data available: Model,
PNC, Serial Number. The information can be found on the rating
plate.

Compressor

There is a risk of damage to the appliance if the compressor is
not used properly.

Service

Refer to the service chapter for information on how to service
the appliance.

Disposal

Refer to the disposal chapter for information on how to dispose
of the appliance.

LWR9516BN4

EN User Manual Washer Dryer

USER MANUAL

2 www.aeg.com
CONTENTS
1. SAFETY INFORMATION………………………………………………………………………….. 3 2. SAFETY INSTRUCTIONS………………………………………………………………………… 6 3. PRODUCT DESCRIPTION………………………………………………………………………..8 4. TECHNICAL DATA………………………………………………………………………………….. 9 5. INSTALLATION………………………………………………………………………………………..9 6. CONTROL PANEL………………………………………………………………………………….15 7. DIAL AND BUTTONS…………………………………………………………………………….. 17 8. PROGRAMMES……………………………………………………………………………………..19 9. BEFORE FIRST USE………………………………………………………………………………27 10. SETTINGS………………………………………………………………………………………….. 28 11. DAILY USE…………………………………………………………………………………………. 28 12. DAILY USE – WASHING & DRYING………………………………………………………..33 13. DAILY USE – DRYING ONLY………………………………………………………………… 35 14. FLUFF IN THE FABRICS……………………………………………………………………….36 15. HINTS AND TIPS………………………………………………………………………………….37 16. CARE AND CLEANING………………………………………………………………………… 39 17. TROUBLESHOOTING………………………………………………………………………….. 47 18. CONSUMPTION VALUES…………………………………………………………………….. 51 19. ENVIRONMENTAL CONCERNS…………………………………………………………….54
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler ­ features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. Visit our website to:
Get usage advice, brochures, trouble shooter, service and repair information: www.aeg.com/support
Register your product for better service: www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance: www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts. When contacting our Authorised Service Centre, ensure that you have the following data available: Model, PNC, Serial Number. The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.

1. SAFETY INFORMATION

ENGLISH 3

Before beginning the installation and use of this appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability. · This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. · Children between 3 and 8 years of age and persons with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised. · Children of less than 3 years of age should be kept away from the appliance unless continuously supervised. · Children should be supervised to ensure that they do not play with the appliance. · Keep all packaging away from children and dispose of it appropriately. · Keep detergents away from children. · Keep children and pets away from the appliance when the door is open. · If the appliance has a child safety device, it should be activated. · Children shall not carry out cleaning and user maintenance of the appliance without supervision.

4 www.aeg.com
1.2 General Safety · This appliance is for washing and drying domestic-
type machine-washable and dryable laundry only. · Do not use the dryer function if laundry has been
soiled with industrial chemicals. · This appliance is designed for single household
domestic use in an indoor environment. · This appliance may be used in, offices, hotel guest
rooms, bed & breakfast guest rooms, farm guest houses and other similar accommodation where such use does not exceed (average) domestic usage levels. · Do not change the specification of this appliance. · The appliance shall be installed as a freestanding product or below the kitchen worktop if space margins permit. · Do not install the appliance behind a lockable door, a sliding door or a door with a hinge on the opposite side, that would prevent the appliance door from being fully open. · Connect the mains plug to the mains socket only at the end of the installation process. Make sure that the mains plug is accessible after installation. · The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering. · WARNING: The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility. · Ensure good air ventilation in the room where the appliance is installed to avoid the backflow of unwanted gases into the room from appliances burning gas or other fuels, including open fires. · Exhaust air must not be discharged into a flue which is used for exhausting fumes from any appliances burning gas or other fuels.

ENGLISH 5
· The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 10 bar (1.0 MPa).
· The appliance maximum load is 10 kg. Do not exceed the maximum load of each programme (refer to the “Programmes” chapter).
· The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre.
· Old hose sets must not be reused. · If the mains power supply cable is damaged, it must
be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. · Wipe away lint or packaging debris that has accumulated around the appliance. · Do not run the appliance without filters. Clean the lint filter before or after each use. · Items that have been soiled with substances such as vegetable or mineral oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed separately with an extra amount of detergent before being dried in the washer dryer. · Do not use the appliance if items have been soiled with industrial chemicals. · Do not dry unwashed items in the wash dryer. · Items such as foam rubber (latex foam), shower caps, waterproof textiles, and rubber backed articles and clothes, or pillows fitted with foam rubber pads should not be dried in the washer dryer. · Fabric softeners, or similar products, should only be used as specified by the product manufacturer’s instructions. · Remove all objects from items that could be a source of fire ignition such as lighters or matches. · WARNING: Never stop the washer dryer before the end of the drying cycle unless all items are quickly

6 www.aeg.com

removed and separated so that residual heat can dissipate. · The final part of the washer dryer cycle takes place without heat (cool down cycle) to ensure that items reach a temperature that will not cause damage to them. · Do not use high pressure water sprays and/or steam to clean the appliance. · Clean the appliance with a moist cloth. Use only neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. · Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket.

2. SAFETY INSTRUCTIONS
2.1 Installation
The installation must comply with relevant national regulations.
· Follow the installation instructions supplied with the appliance.
· Do not install or use the appliance where the temperature can be less than 5°C or higher than 35 °C.
· Always keep the appliance vertical when it is being moved.
· To make sure the compressor works properly, wait 6 hours after the installation before using the appliance.
· Make sure that there is air circulation between the appliance and the floor.
· Remove all the packaging and the transit bolts.
· The floor area on which the appliance is to be installed must be flat, stable, heat resistant and clean.
· Keep the transit bolts in a safe place. If the appliance is to be moved in the future they must be reattached to lock the drum to prevent an internal damage.
· Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear.

· Do not install or use a damaged appliance.
· Do not install the appliance where the appliance door cannot be fully opened.
· Adjust the feet to have the necessary space between the appliance and the flooring.
· When the appliance is in its permanent position, check if it is levelled correctly with the aid of a spirit level. If it is not, adjust the feet accordingly.
2.2 Electrical Connection
WARNING! Risk of fire and electric shock.
· WARNING: This appliance is designed to be installed / connected to a grounding connection in the building.
· Always use a correctly installed shockproof socket.
· Do not use multi-plug adapters and extension cables.
· Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.

· Do not touch the mains cable or the mains plug with wet hands.
2.3 Water Connection
· The inlet water shall not exceed 25 °C.
· Do not cause damage to the water hoses.
· Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear.
· Ensure that there are no visible water leaks during and after the first use of the appliance.
· Do not use an extension hose if the inlet hose is too short. Contact the Authorised Service Centre for the replacement of the inlet hose.
· When unpacking the appliance, It is possible to see water flowing from the drain hose. This is due to the testing of the appliance with the use of water in the factory.
· You can extend the drain hose to maximum 400 cm. Contact the Authorised Service Centre for the other drain hose and the extension.
· Make sure that there is access to the tap after the installation.
2.4 Use
WARNING! Risk of injury, electric shock, fire, burns or damage to the appliance.
· Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
· Do not touch the glass door while a programme operates. The glass can get hot.
· Do not dry damaged (torn, frayed) items that contain padding or fillings.
· If laundry has been washed with a stain remover, carry out an additional rinse cycle before starting a drying cycle.
· Make sure that all metal objects are removed from the laundry.

ENGLISH 7
· Dry only fabrics that are suitable to dry in the appliance. Follow the cleaning instruction on the item label.
· Do not sit or stand on the open door of the appliance.
· Do not dry dripping wet clothes in the appliance.
· Do not let hot items to touch the plastic parts of the appliance.
· Remove a detergent ball (if used) before starting a drying programme.
· Do not use a detergent ball if setting a non-stop programme.
2.5 Compressor
WARNING! Risk of damage to the appliance.
· The compressor and its system in the washer-dryer is filled with the special agent which is free from fluorochlorohydrocarbons. This system must stay tight. The damage of the system can cause a leakage.
2.6 Service
· To repair the appliance contact the Authorised Service Centre. Use original spare parts only.
· Please note that self-repair or nonprofessional repair can have safety consequences and might void the guarantee.
· The following spare parts will be available for 10 years after the model has been discontinued: motor and motor brushes, transmission between motor and drum, pumps, shock absorbers and springs, washing drum, drum spider and related ball bearings, heaters and heating elements, including heat pumps, piping and related equipment including hoses, valves, filters and aquastops, printed circuit boards, electronic displays, pressure switches, thermostats and sensors, software and firmware including reset software, door, door hinge and seals, other seals, door locking assembly, plastic peripherals such as detergent dispensers. Please note that some of these spare parts are only available to professional

8 www.aeg.com
repairers, and that not all spare parts are relevant for all models. · Concerning the lamp(s) inside this product and spare part lamps sold separately: These lamps are intended to withstand extreme physical conditions in household appliances, such as temperature, vibration, humidity, or are intended to signal information about the operational status of the appliance. They are not intended to be used in other applications and are not suitable for household room illumination.
3. PRODUCT DESCRIPTION
3.1 Appliance overview
12 3 4

2.7 Disposal
· Disconnect the appliance from the mains electrical and water supplies.
· Cut off the mains electrical cable close to the appliance and dispose of it.
· Remove the door catch to prevent children or pets from becoming trapped in the drum.
· Dispose of the appliance in accordance with local requirements for the disposal of Waste Electrical and Electronic Equipment (WEEE).

10

11

5 6
7

12 13 14

9
1 Worktop 2 Detergent dispenser 3 Air filter(s) 4 Control panel 5 Door handle 6 Rating plate 7 Drain pump filter 8 Feet for levelling the appliance

8
9 Airflow slots 10 Water drain hose 11 Water inlet valve 12 Mains cable 13 Transit bolts 14 Hose supports

ENGLISH 9

A

B Mod. xxxxxxxxx

Prod.No. 910000000 00

C

000V ~ 00Hz 0000 W

D

00A
00000000

The rating plate reports: A. model name B. product number C. electrical ratings D. serial number

4. TECHNICAL DATA

Dimension

Width/ Height/ Total depth

59.7 cm /87.0 cm /66.0 cm

Electrical connection

Voltage Overall power Fuse Frequency

230 V 2200 W 10 A 50 Hz

Level of protection against ingress of solid particles and moisture ensured by the protective cover, ex- cept where the low voltage equipment has no pro- tection against moisture

IPX4

Water supply 1)

Cold water

Water supply pressure Minimum Maximum

0.5 bar (0.05 MPa) 10 bar (1.0 MPa)

Ambient temperature

Minimum Maximum

5 °C 35 °C

Maximum wash load

Cotton Synthetics Wool

10 kg 4 kg 1.5 kg

Maximum dry load

Cotton

6 kg

Synthetics

4 kg

Wool

1 kg

Spin Speed

Maximum spin speed

1551 rpm

This product contains HFC – R134a/GWP1430 0.14 kg fluorinated gas hermetically sealed.

1. Connect the water inlet hose to a water tap with a 3/4” thread.

5. INSTALLATION

WARNING! Refer to Safety chapters.

5.1 Unpacking
WARNING! Remove all the packaging and the transit bolts before installing the appliance.

10 www.aeg.com
WARNING! As you will put down the appliance on the rear side, wait about 6 hours before you use it. This time is necessary to enable the compressor to work properly.
WARNING! Use the gloves.
1. Remove the external film. If necessary, use a cutter.

5. Carefully put the appliance down on its rear side.
6. Put the front polystyrene packaging element on the floor under the appliance.
Make sure not to damage the hoses.

2. Remove the cardboard top and the polystyrene packaging materials.
7. Remove the polystyrene protection from the bottom.

3. Remove the internal film.

1
2 8. Pull up the appliance in vertical
position.

4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum.

ENGLISH 11
10. Remove the three bolts by using the spanner supplied with the appliance.

9. Remove the power supply cable and the drain hose from the hose holders.
It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory.

11. Pull out the plastic spacers. 12. Put the plastic caps, that you find in
the user manual bag, in the holes.

We recommend that you keep the packaging and the transit bolts for any movement of the appliance.

5.2 Installation under a counter

600 mm 630 mm
870 mm

The appliance can be installed as freestanding or below the kitchen counter with correct space (see picture).
CAUTION! Do not install the appliance inside a sealed hollow! Make sure that there is air circulation throw the bottom of the furniture.

CAUTION! To assure free air circulation under the appliance, do not attach the sound barriers (if available).

12 www.aeg.com
5.3 Positioning and levelling
1. Install the appliance on a flat hard floor.
Make sure that carpets do not stop the air circulation below the appliance. Make sure that the appliance does not touch the wall or other units. 2. Loosen or tighten the feet to adjust the level.
WARNING! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level.

5.4 The inlet hose
1. Connect the water inlet hose to the back of the appliance.
2. Position it toward left or right depending on the position of the water tap.

45º 20º

x4
The appliance must be level and stable.
A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation.
When the appliance is installed on a plinth, use the accessory described in chapter ‘Accessories’. Read carefully the instructions supplied with the appliance and with the accessory.

Make sure that the inlet hose is not in vertical position.
3. If necessary, loose the ring nut to set it in the correct position.
4. Connect the water inlet hose to the cold water tap with 3/4″ thread.

WARNING! The inlet water shall not exceed 25 °C.

CAUTION! Make sure that there are no leaks from the couplings.
Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose.
5.5 Water-stop device
The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing.
The red sector in the window «A» shows this fault.

ENGLISH 13
2. On the edge of a sink – Fasten the guide to the water tap or to the wall. Make sure that the plastic guide cannot move when the appliance drains.

A
If this occurs, close the water tap and contact the authorized service centre to replace the hose.
5.6 Water drainage
The drain hose should be positioned at a height of not less than 60 cm and not more than 100 cm from the floor.
You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension.
It is possible to connect the drain hose in different ways:
1. Make a U shape with the drain hose and put it around the plastic hose guide.

Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3. To a stand pipe with vent-hole Insert the drain hose directly into a drain pipe. Refer to the illustration.
The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.5″) must be larger than the external diameter of the drain hose.

14 www.aeg.com
4. If the end of the drain hose looks like this (see the picture), you can push it directly into the stand pipe.
5. Without the plastic hose guide, to a sink spigot – Put the drain hose in the spigot and tighten it with a clamp. Refer to the illustration.

5.7 Electrical connection
At the end of installation you can connect the mains plug to the mains socket.
The rating plate and the ‘Technical Data’ chapter indicate the necessary electrical ratings. Make sure that they are compatible with the mains power supply.
Check that your domestic electrical installation can take the maximum load required, also taking into account any other appliances in use.
Connect the appliance to an earthed socket.

Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink.
6. Position the hose directly to a builtin drain pipe in the room wall and tighten it with a clamp.

The power supply cable must be easily accessible after installing the appliance.
For any electrical work required to install this appliance, contact our Authorised Service Centre.
The manufacturer does not accept any responsibility for damage or injury through failure to comply with the above safety precaution.

6. CONTROL PANEL
6.1 Control panel description
1

ENGLISH 15

2

3

4 5

12

11 10 9 8 7

6

1 Programme dial 2 Display 3 Droogtijd/Minuterie touch button 4 Droogtegraad/Niveau séchage touch
button 5 MODUS/MODE touch button and
· Wassen/Lavage mode · Drogen/Séchage mode 6 Start/Pauze/Départ/Pause touch button 7 Opties/Options touch button, permanent Extra Rinse option and
6.2 Display

· Vlekken/Taches option · Voorwas/Prélavage option
8 Startuitstel/Départ Différé touch button
9 Tijd besparen/Rapide touch button 10 Centrifugeren/Essorage touch button,
child lock option and · Pompen/Vidange option · Centrifugeren/Essorage option
11 Temp. touch button 12 Aan/Uit/Marche/Arrêt push button

16 www.aeg.com

Washing phase indicator: it flashes during prewash and wash phase.

Rinsing phase indicator. It flashes during rinse phase.

Spin and drain phase indicator. It flashes during spin and drain phase.

Drying phase indicator.

Drying time indicator.

Door locked indicator.

The digital indicator can show: · Programme duration (e. g.

, washing and/or drying phase).

· Delay time (e. g. or ).

· Cycle end ( ).

· Warning code (e.g.

).

· Maximum load indicator ( ). The value is shown for three sec- onds after programme selection, alternated with cycle duration. The

icon flashes during laundry load estimation (refer to “PROS- ENSE load detection” paragraph).

Maximum laundry indicator. It flashes when the laundry load exceeds the maximum declared load of the selected programme. If you run a

programme when the drum is overloaded, end of the programme.

also flashes at the

Indicator for the cleaning of air filters.

The permanent Extra Rinse option.

Child safety lock indicator.

Temperature indicator. The set.
Extra Silent indicator.

indicator appears when a cold wash is

Rinse hold indicator.

Spin speed indicator.

Iron drying indicator.

Cupboard drying indicator.

Extra drying indicator.

ENGLISH 17

7. DIAL AND BUTTONS
7.1 Aan/Uit/Marche/Arrêt
Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off.
As the Stand-by function automatically deactivates the appliance to decrease the energy consumption in a few cases, you may need to activate the appliance again.
For more details, refer to Stand-by paragraph in Daily Use chapter.
7.2 Introduction
The options/functions are not selectable with all washing programmes. Check the compatibility between options/functions and washing programmes in the “Programme Chart”. An option/function can exclude another one, in this case the appliance doesn’t allow you to set the incompatible options/functions together. Make sure the screen and touch buttons are always clean and dry.
7.3 Temp.
When you select a washing programme, the appliance automatically proposes a default temperature.
Touch this button repeatedly until the desired temperature value appears on the display.
When the display shows the indicators
and , the appliance does not heat the water.

7.4 Centrifugeren/Essorage
When you set a programme, the appliance automatically sets the default spin speed allowed.
Touch repeatedly this button to: · Change the spin speed.
The display shows only the spin speeds available for the set programme.
· Activate the Rinse Hold option. The final spin is not performed. The water of the last rinse is not drained out to prevent the fabrics from creasing. The washing programme ends with water in the drum.
The display shows the indicator . The door stays locked and the drum turns regularly to reduce creasing. You must drain the water to unlock the door. If you touch the Start/Pauze/Départ/ Pause button, the appliance performs the spinning phase and drains the water.
The appliance empties the water out automatically after 18 hours approximately.
· Activate the Extra Silent option. The intermediate and the final spinning phases are suppressed and the programme ends with water in the drum. This helps to reduce creasing.
The display shows the indicator . The door stays locked. The drum turns regularly to reduce creasing. You must drain the water to unlock the door. As the programme is very quiet, it is suitable for use at night time when cheaper electricity tariffs are available. In some programmes the rinses are performed with more water.

18 www.aeg.com

If you touch the Start/Pauze/Départ/ Pause button, the appliance performs the only draining phase.

The appliance empties the water out automatically after 18 hours approximately.
· Activate the drain-only option (Skipping the wash, rinse and spin phases): Pompen/Vidange. The appliance performs the only draining phase of the selected washing programme.
The display shows the indicator

(cold), and the indicator

(no

spin) and the indicator . · Activate the spin-only option
(Skipping the wash and rinse phases): Centrifugeren/Essorage.

Before setting this option, select a suitable washing programme for the garments. The appliance will performs the most fitting spin cycle for your garments care (e.g. For synthetics items, first select the Synthetica/ Synthétiques washing programme and then the Centrifugeren/Essorage option).

The appliance performs only the spinning phase of the selected washing programme.
The display shows the indicator
(cold), the phase indicator and the spin speed.

7.5 Opties/Options
Press this button repeatedly to activate one of the two options.
The relevant indicator goes on in the display.

· Vlekken/Taches Select this option to add an anti-stain phase to a programme in order to treat heavily soiled or stained laundry with stain remover.

Pour the stain remover into
compartment . The stain remover will be added in the appropriate phase of the washing programme.
This option is not available with a temperature lower than 40 °C.
· Voorwas/Prélavage Use this option to add a pre-wash phase at 30 °C before the washing phase. This option is recommended for heavily soiled laundry, especially if containing sand, dust , mud and other solid particles.
The options can increase the programme duration.
These two options cannot be set together.
7.6 Startuitstel/Départ Différé
With this option you can delay the start of a programme in a more convenient time.
Tap on the button repeatedly to set the required delay. The time increases by steps of 30 minutes up to 90′ and from 2 hours up to 20 h.
After starting the cycle by the means of the Start/Pauze/Départ/Pause button, the display shows the selected delay time and the appliance begins the countdown.
7.7 Tijd besparen/Rapide
With this option you can decrease the programme duration.
· If your laundry is normally or lightly soiled, it may be advisable to shorten the washing programme. Touch this button once to decrease the duration.
· In case of smaller load, touch this button twice to set an extra quick programme.
On the display the programme duration is adjusted accordingly.
When this button is set, the led above the button is on.

ENGLISH 19

This option can also be used to shorten the steam programme duration.
7.8 Droogtijd/Minuterie
In the programme where it is selectable, touch this button to set the time that suits the fabrics you have to dry (refer to “Timed drying” table). The display shows the set value.
Each time you touch this button the time value increases by 5 minutes.
You cannot set all time values for different types of fabrics.
7.9 Droogtegraad/Niveau séchage
Touch this button to set one of 3 automatic dryness levels proposed by the appliance.
On the display the relevant dryness indicator goes on:

·

Iron dry: laundry to be

ironed.

8. PROGRAMMES

8.1 Programme Chart

·

Cupboard dry: laundry to

be put in store.

·

Extra dry: laundry to be

fully dried.

You can not set all automatic levels for each type of fabrics.

7.10 MODUS/MODE
Thanks to this button, a cycle can perform: · Only washing : Wassen/Lavage
indicator is on. · Washing and drying : Wassen/
Lavage and Drogen/Séchage indicators are on. · Only drying : Drogen/Séchage indicator is on.
7.11 Start/Pauze/Départ/ Pause
Touch the Start/Pauze/Départ/Pause button to start, pause the appliance or interrupt a running programme.

Programme Default tempera- ture Temperature range

Reference spin speed Spin speed range

Maxi- mum load

Programme description

Eco 40-60 (Wash only mode)
40 °C1)

1600 rpm 1600 rpm 400 rpm

Eco 40-60 + Cup- 1600 rpm

board dry level

1600 rpm –

(Wash & Dry mode) 1000 rpm

40 °C2)

10 kg
White cotton and coloured cotton. Nor- mally, heavily and lightly soiled items. 6 kg

20 www.aeg.com

Programme Default tempera- ture Temperature range

Reference spin speed Spin speed range

Maxi- mum load

Programme description

Eco 40-60 + Cup- board dry level (Dry

–

only mode)

Katoen/Coton 40 °C 95 °C – Cold

1600 rpm 1600 rpm 400 rpm

Synthetica/Synthé- tiques 40 °C 60 °C – Cold

1200 rpm 1200 rpm 400 rpm

Non Stop 3h/3kg 30 °C 40 °C – 30 °C

1200 rpm

Fijne was/Délicats 30 °C 40 °C – Cold

1200 rpm 1200 rpm 400 rpm

Zije/Soie 30 °C

1000 rpm 1000 rpm 400 rpm

Wol/Handwas/ Laine/Lavage à la main 40 °C 40 °C – Cold

1200 rpm 1200 rpm 400 rpm

6 kg White cotton and fast-coloured cotton.

10 kg

White cotton and coloured cotton. Nor- mally, heavily and lightly soiled items.

Synthetic items or mixed fabric items. Normally soiled items.
4 kg

3 kg 2 kg

Mixed fabrics (cotton and synthetic items). Complete programme to wash and dry laundry loads up to 3 kg in one
go. It only lasts 3 hours.

Also, the indicator play.

appears on the dis-

Delicate fabrics such as acrylics, vis- cose and mixed fabrics requiring gen- tler washing. Normally and lightly soiled items.

0.5 kg 1.5 kg

Machine and hand washable silk and other delicate fabrics . Drum move- ments are so gentle that is possible to treat even very delicate garments. Run a complete wash and dry cycle to reduce creases.
Machine washable wool, hand washa- ble wool and other fabrics with «hand washing» care symbol3).

ENGLISH 21

Programme Default tempera- ture Temperature range
Outdoor 30 °C 40 °C – Cold

Reference spin speed Spin speed range

Maxi- mum load

1200 rpm

1200 rpm –

2 kg

400 rpm

Programme description
Do not use fabric softener and make sure that there is no softener residue in the detergent dispenser.
Outdoor clothing, technical, sport fab- rics, waterproof and breathable jack- ets, shell jackets with a removable fleece or inner insulation.
By performing a combined wash and dry programme, the drying phase also acts as water-repellent restorer. Make sure that the gar- ment care label permits tumble drying.

Stoom/Vapeur

Steam programmes 4)

Steam can be used for dried, washed or worn once laundry. These pro- grammes can reduce creases and odours and make your laundry softer.

Do not use any detergent. If necessa-

ry, remove

stains by washing or using localized

stain removal.

–

1 kg

Steam

programmes do not perform any hy-

gienic cycle.

Do not set a Steam programme with these types of items:

· Items to be washed at a temperature lower than 40°C.
· Items where it is not specified on the care label as being suitable for tumble drying.
· Items with label “Dry clean only”.

22 www.aeg.com

Programme Default tempera- ture Temperature range

Reference spin speed Spin speed range

Maxi- mum load

Programme description

Spoelen/Rinçage

1600 rpm 1600 rpm 400 rpm

10 kg

To rinse and spin the laundry. All fab- rics, except woollens and very delicate fabrics. Reduce the spin speed accord-
ingly to the type of laundry.

1. According to Commission Regulation EU 2019/2023. This programme at default temperature and spin speed, in washing only mode, with rated capacity 10 kg is able to clean normally soiled cotton laun-
   dry declared to be washable at 40 °C or 60 °C, together in the same cycle.

For the reached temperature in the laundry, the programme duration and other data, please refer to ‘Consumption Values’ chapter. The most efficient programmes in terms of energy consumption are generally those that perform at lower temperatures and longer duration.

2. According to Commission Regulation EU 2019/2023. This programme at default temperature and spin speed, in washing and drying mode, with rated capacity 6 kg and with Cupboard dry level performs the wash and dry cycle able to clean normally soiled cotton laundry declared to be washable at 40 °C or 60 °C, together in the same cycle and, after drying phase, the laundry can be immediately stored in a cupboard. 3) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn’t rotate or doesn’t rotate properly, but this is normal for this programme. 4) If you set a Steam programme with dried laundry, at the end of the cycle the laundry could be humid. It is better to expose the items to the fresh air for about 10 minutes to let the humidity dry. When the pro- gramme is completed, quickly remove the laundry from the drum. After a steam cycle, items may be iron- ed however with less effort.

Programme Eco 40-60 Katoen/Coton Synthetica/Synthétiques Non Stop 3h/3kg Fijne was/Délicats Zije/Soie Wol/Handwas/Laine/Lavage à la main Outdoor Stoom/Vapeur Spoelen/Rinçage

Programme options compatibility Options

ENGLISH 23

Centrifugeren/

Essorage

Pompen/Vidange

Centrifugeren/ Essorage 1)

Extra Spoelen/ Rinçage Plus

Voorwas/Prélav-

age 2)

Vlekken/Taches 3)

Startuitstel/

Départ Différé

Programme Eco 40-60 Katoen/Coton Synthetica/Synthétiques Non Stop 3h/3kg Fijne was/Délicats Zije/Soie Wol/Handwas/Laine/Lavage à la main Outdoor Stoom/Vapeur Spoelen/Rinçage

24 www.aeg.com Options

Tijd besparen/

Rapide 4)

Droogtijd/Minute-

rie

Droogtegraad/

Niveau séchage

1. Before setting this option, select a suitable washing programme for the garments. The appliance will performs the most fitting spin cycle for your garments care (e.g. For synthetics items, first select the Syn- thetica/Synthétiques washing programme and then the Centrifugeren/Essorage option). 2) Voorwas/Prélavage and Vlekken/Taches options cannot be selected together. 3) This option is not available with temperature lower than 40 °C.
2. If you set the shortest duration, we recommend that you decrease the load size. It is possible to fully load the appliance, however the washing results can be less satisfactory. 5) Iron Dry is not available with this programme.

Suitable detergents for each programme

Programme Universal powder1)

Liquid Uni- Liquid for

versal

coloureds

Delicates woollens

Special

Eco 40-60

—

—

Katoen/ Coton

—

—

Synthetica/ Synthétiques

—

—

ENGLISH 25

Programme Universal powder1)

Non Stop 3h/3kg

—

Fijne was/ Délicats

—

Zije/Soie

—

Liquid Uni- Liquid for

versal

coloureds

Delicates woollens

—

—

—

—

—

Special
–

Wol/Hand-

was/Laine/ Lavage à la

—

—

—

main

Outdoor

—

—

—

1. At temperature higher than 60 °C the use of powder detergent is recommended.

= Recommended — = Not recommended
8.2 Woolmark Wool Care Blue
· The wool wash cycle of this machine has been approved by The Woolmark

Company for the washing of wool garments labelled as “hand wash” provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine. M1230. · The wool drying cycle of this machine has been tested and approved by The Woolmark Company. The cycle is suitable to dry wool garments which are labelled “hand wash” provided that the garments are washed in a Woolmark endorsed hand washing cycle and dried according to the instructions issued by the manufacturer. M1399. The Woolmark symbol is a Certification mark in many countries.

8.3 Automatic drying

Initial cycle times for programmes with Droogte- graad/Niveau séchage option are only estimates, the actual drying time may slightly differ from the time displayed.

26 www.aeg.com

Dryness Level Extra Dry For towelling materials Cupboard Dry For items to be stored
Iron Dry Suitable for ironing

Type of fabric

Load

Cottons and Linen

up to 6 kg

(bathrobes, bath towels, etc)

Cottons and Linen

up to 6 kg

(bathrobes, bath towels, etc)

Synthetics and mixed fab- rics (jumpers, blouses, under-
wear, household and bed lin-
en)

up to 4 kg

Delicate fabrics (acrylics, viscose and deli-
cate mixed fabrics)

up to 2 kg

Wool items (woollen jumpers)

up to 1 kg

Outdoor sporting garments up to 2 kg (outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets)

Zije/Soie

up to 1 kg

(silk garments and very deli-

cate items)

Cottons and Linen (sheets, tablecloths, shirts,
etc)

up to 6 kg

8.4 Timed drying

Dryness Level Type of fabric

Extra Dry For towelling
materials

Cottons and Linen (bathrobes, bath towels, etc)

Load (kg)

Spin spee d (rpm)

Suggested duration (mins)

6 1400 280 – 300

4 1400 190 – 210

2 1400 110 – 130

ENGLISH 27

Dryness Level Type of fabric

Load (kg)

Spin spee d (rpm)

Suggested duration (mins)

Cupboard Dry For items to be
stored

Cottons and Linen (bathrobes, bath towels, etc)

6 1400 4 1400 2 1400

270 – 290 180 – 200 100 – 120

Synthetics and mixed fabrics (jumpers, blouses, underwear, house-
hold and bed linen)

4 1200 2 1200

150 – 170 70 – 90

Delicates (acrylics, viscose and delicate mixed
fabrics)

2 1200 1 1200

120 – 140 80 – 100

Wool (woollen jumpers)

1 1200

80 – 100

Outdoor sporting garments (outdoor clothing, technical, sport fab-
rics, waterproof and breathable jackets,
shell jackets)

2 1200 1 1200

140 – 160 90 – 110

Zije/Soie (silk garments and very delicate items)

1 1000

50 – 70

Iron Dry

Cottons and Linen

Suitable for iron- (sheets, tablecloths, shirts, etc)

ing

6 1400 4 1400 2 1400

150 – 170 100 – 120
60 – 80

9. BEFORE FIRST USE
During installation or before first use you may observe some water in the appliance. This is a residual water left in the appliance after a full functional test in the factory to ensure the appliance is delivered to customers in perfect working order and is no cause for concern.
1. Make sure that all transit bolts have been removed from the appliance.
2. Make sure that the electrical power is available and the water tap is open.

3. Pour 2 litres of water into the detergent compartment marked by
. This action activates the drain system. 4. Pour a small quantity of detergent
into the compartment marked by . 5. Set and start a programme for cotton
at the highest temperature without any laundry in the drum. This removes all possible dirt from the drum and the tub.

28 www.aeg.com

10. SETTINGS
10.1 Child Lock
With this option you can prevent children from playing with the control panel.
· To activate/deactivate this option, touch the Centrifugeren/Essorage
button until the indicator comes on/goes off on the display. You can activate this option:
· After you touch the Start/Pauze/ Départ/Pause button: all the buttons and the programme dial are deactivated (except Aan/Uit/Marche/ Arrêt button ).
· Before you touch the Start/Pauze/ Départ/Pause button: the appliance cannot start.
The appliance keeps the selection of this option after you switch it off.
10.2 Acoustic signals
To deactivate the acoustic signals when the programme is completed touch the

Opties/Options and the Startuitstel/ Départ Différé buttons simultaneously for about 3 seconds.
The acoustic signals, they continue operate when the appliance has a malfunction.
10.3 Permanent Extra Rinse
With this option you can permanently have an extra rinse when you set a new programme.
To activate/deactivate this option, hold the Opties/Options button pressed for 3 seconds until the indicator comes on/ goes off on the display. When it is activated, the appliance will default to this option after you switch it off or change/reset the programme.
This option increases the programme duration.

11. DAILY USE
WARNING! Refer to Safety chapters.
11.1 Activating the appliance
1. Connect the mains plug to the mains socket.
2. Open the water tap. 3. Press the Aan/Uit/Marche/Arrêt
button for a few seconds to activate the appliance. The indicator of the Start/Pauze/Départ/Pause button starts flashing. The programme dial is automatically set on default programme and only the indicator Wassen/Lavage is on above the MODUS/MODE button.
The display shows the maximum load, the default temperature, the maximum spin speed, the indicators of the phases making up the programme and the cycle duration.

11.2 Loading the laundry
1. Open the appliance door. 2. Shake the items before you put them
in the appliance. 3. Put the laundry in the drum, one item
at a time. Make sure not to put too much laundry in the drum. 4. Close the door firmly.

ENGLISH 29

CAUTION! Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry.
CAUTION! Washing heavily oiled, greasy stains could cause damage rubber parts of the washing machine.
11.3 Filling the detergent and additives

After a washing cycle, if necessary, remove any detergent residue from the detergent dispenser.
11.4 Check the position of the flap
1. Pull out the detergent dispenser until it stops.
2. Press the lever down to remove the dispenser.
1

2

Compartment for prewash phase, soak programme or stain remover. Compartment for washing phase.
Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Flap for powder or liquid detergent.

3. To use powder detergent, turn the flap up.

Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum
indicated level ( ). This quantity will however guarantee the best washing results.

4. To use liquid detergent, turn the flap down.

30 www.aeg.com

With the flap in the position DOWN:
· Do not use gelatinous or thick liquid detergents.
· Do not put more liquid detergent than the limit shown on the flap.
· Do not set the prewash phase.
· Do not set the delay start function.
5. Measure out the detergent and the fabric conditioner.
6. Carefully close the detergent dispenser.

The display shows the maximum declared load for the programme (for a few seconds), the default temperature, the maximum spin speed, the washing phase indicators (when available) and an indicative programme duration. 2. To change the temperature and/or
the spin speed, touch the related buttons. 3. If desired, set one or more options by touching the related buttons. The related indicators come on in the display and the given information changes accordingly.
To perform washing only, make sure that only the Wassen/Lavage indicator is on above the MODUS/ MODE button.
In case a selection is not possible, no indicator comes on and an acoustic signal sounds.
11.6 Starting a programme
Touch the Start/Pauze/Départ/Pause button to start the programme. The related indicator stops flashing and stays on. In the display, the indicator of the operating phase starts flashing. The programme starts, the door is locked. The display shows the indicator
.
The drain pump can operate shortly before the appliance fills water.

Make sure that the flap does not cause a blockage when you close the drawer.
11.5 Setting a programme
1. Turn the programme dial to select the desired washing programme. The related programme indicator comes on.
The indicator of the Start/Pauze/Départ/ Pause button flashes.

11.7 Starting a programme with the delay start
1. Touch this repeatedly until the display shows the desired delay time. The indicator Startuitstel/Départ Différé comes on.
2. Touch the Start/Pauze/Départ/Pause button.
The appliance starts the countdown of the delay start. When the countdown is completed, the programme starts.

The ProSense estimation starts at the end of the countdown.
Cancelling the delay start after the countdown has started
To cancel the delay start:
1. Touch the Start/Pauze/Départ/Pause button to pause the appliance. The related indicator flashes.
2. Touch the Startuitstel/Départ Différé button repeatedly until the display shows .
3. Touch the Start/Pauze/Départ/Pause button again to start the programme immediately.
Changing the delay start after the countdown has started
To change the delay start:
1. Touch the Start/Pauze/Départ/Pause button to pause the appliance. The related indicator flashes.
2. Touch the Startuitstel/Départ Différé button repeatedly until the display shows the desired delay time.
3. Touch the Start/Pauze/Départ/Pause button again to start the new countdown.
11.8 The ProSense System load detection
The programme duration in the display is referred to a medium/high load.
After touching the Start/Pauze/Départ/ Pause button, the maximum declared
load indicator goes off, the indicator flashes, the ProSense System starts the laundry load detection:
1. The appliance detects the load in the
first 30 seconds, the indicator
flashes. the digit area shows and the drum rotates shortly. 2. At the end of the load detection, the
indicator stop flashing. The programme duration will be adjusted accordingly and could increase or

ENGLISH 31

decrease. After further 30 seconds, the water filling starts.

At the end of the load detection, in case

of drum overload, the indicator

is

flashing in the display.

In this case, for 30 seconds, it is possible to pause the appliance and remove the exceeding garments.

Once removed the exceeding garments, touch the Start/Pauze/Départ/Pause button to start the programme again. The ProSense System phase can be repeated up to three times (see point 1).

Important! If the laundry amount will not be reduced, the washing programme starts anyway, despite the overload. In this case, it will be not possible to guarantee the best washing results.

About 20 minutes after the programme start, the programme duration could be adjusted again depending on the capacity of water absorption of the fabrics.

The ProSense System detection is carried out with complete washing programmes only (no skipping phase selected).

The ProSense System is not available with some programmes, such as Wol/ Handwas/Laine/Lavage à la main, programmes with short cycles and without washing phase.

11.9 Programme phase indicators
When the programme starts the indicator of the running phase flashes and the other phase indicators are steady on.
E.g. the washing or pre wash phase is

running:

.

When the phase ends the relevant indicator stops flashing and is steady on. The next phase indicator starts flashing.

32 www.aeg.com

E.g. the rinse phase is running:

.

If you select the a steam programme, the

steam phase indicator comes on.

11.10 Interrupting a programme and changing the options
When the programme is running, you can change only some options:
1. Touch the Start/Pauze/Départ/Pause button.
The related indicator flashes. 2. Change the options. The given
information in the display changes accordingly. 3. Touch the Start/Pauze/Départ/Pause button again. The washing programme continues.

11.11 Cancelling a running programme
1. Press the Aan/Uit/Marche/Arrêt button to cancel the programme and to deactivate the appliance.
2. Press the Aan/Uit/Marche/Arrêt button again to activate the appliance.
Now, you can set a new washing programme.
If the ProSense phase is already carried out and the water filling is already started, the new programme starts without repeating the ProSense phase. The water and the detergent are not drained out in order to avoid waste. The display shows the maximum duration of the programme, updating it about 20 minutes after the starting of the new programme.

11.12 Opening the door Adding garments

While a programme or the delay start operates, the appliance door is locked.
If the temperature and level of the water in the drum are too high and/or the drum still rotates you cannot open the door.
1. Touch the Start/Pauze/Départ/Pause button.
In the display the related door lock indicator goes off. 2. Open the appliance door. If
necessary, add or remove the items. 3. Close the door and touch the Start/
Pauze/Départ/Pause button. The programme or the delay start continues. 4. The door can be opened when the
programme is complete, or set spinning or draining programme/ option and than press Start/Pauze/ Départ/Pause button.
11.13 End of the programme
When the programme has finished, the appliance stops automatically. The acoustic signals operate (if they are active).
In the display all washing phase indicators become steady and the time
area shows .
The indicator of the Start/Pauze/Départ/ Pause button goes off.
The door unlocks and the indicator goes off.
flashes at the end of the programme in case of overloaded drum.
1. Press the Aan/Uit/Marche/Arrêt button to deactivate the appliance.
After five minutes from the end of the programme, the energy saving function automatically deactivates the appliance.
When you activate the appliance again, the display show the end of the last selected programme. Turn the programme dial to set a new cycle.
2. Remove the laundry from the appliance.

ENGLISH 33

3. Make sure that the drum is empty. 4. Keep the door and the detergent
dispenser slightly ajar to prevent mildew and odours. 5. Close the water tap.
11.14 Draining water out after end of cycle
If you have chosen a programme or an option that does not empty out the water of the last rinse, the programme is completed, but:
· The display shows the indicator , the
option indicator or and the
door locked indicator . The
indicator of the running phase flashes. · The drum still turns at regular intervals to prevent the creases in the laundry. · The door stays locked. · You must drain the water to open the door:
1. If necessary, touch the Centrifugeren/Essorage button to decrease the spin speed proposed by the appliance.
2. Touch the Start/Pauze/Départ/Pause button:
· If you have set , the appliance drains the water and spins.
· If you have set , the appliance only drains the water.
The option indicator or goes off,
while the indicator flashes and then goes off.

3. When the programme is completed
and the door locked indicator goes off, you can open the door. 4. Press the Aan/Uit/Marche/Arrêt button a few seconds to deactivate the appliance.
In any case, the appliance empties the water out automatically after approximately 18 hours.
11.15 Stand-by option
The Stand-by function automatically deactivates the appliance to decrease the energy consumption when:
· You do not use the appliance for 5 minutes before you touch the Start/ Pauze/Départ/Pause button. Press the Aan/Uit/Marche/Arrêt button to activate the appliance again.
· After 5 minutes from the end of the washing programme Press the Aan/Uit/Marche/Arrêt button to activate the appliance again. The display shows the end of the last set programme. Turn the programme dial to set a new cycle.
If you set a programme or an option that ends with water in the drum, the Stand-by function doesn’t deactivate the appliance to remind you to drain the water.

12. DAILY USE – WASHING & DRYING

WARNING! Refer to Safety chapters.
This appliance is an automatic washer dryer.

12.1 Complete wash&dry programmes
Automatic Non-Stop programme
The appliance is equipped with the Non Stop 3h/3kg programme, an automatic one-go programme where it is not

34 www.aeg.com
necessary to set the Drogen/Séchage mode.
To run this programme:
1. After loading laundry and detergent, press the Aan/Uit/Marche/Arrêt button for some seconds to activate the appliance.
2. Set the Non Stop 3h/3kg programme by means of the programme dial.
The indicator appears on the display 3. Touch the Start/Pauze/Départ/Pause
button to start the programme.
Non-automatic wash&dry programmes
In some washing programmes, you can combine Wassen/Lavage and Drogen/ Séchage mode for running a complete wash&dry programme.
Proceed as follows:
1. After loading laundry and detergent, press the Aan/Uit/Marche/Arrêt button for some seconds to activate the appliance.
2. Load the laundry one item at a time. 3. Put the detergent and the additives in
the appropriate compartment. 4. Turn the programme dial to the
washing programme. The display shows the default temperature and spin. If necessary, change them according to your laundry. The display also shows the maximum recommended load for washing phase. 5. Set the desired options, if there are available. 6. Touch the MODUS/MODE button once to activate also the drying function. The Wassen/Lavage and Drogen/Séchage indicators come on.
The indicators and appear on the display. The display also shows the maximum recommended load for a washing and drying programme (e.g. 6 kg for cottons). 7. Now, you can choose an automatic drying level or a specific timed drying.

At the beginning of the drying cycle (3 – 5 minutes), a slightly higher noise can be heard. This is caused by the compressor and it is quite normal for compressor powered appliances such as refrigerators, freezers and so on.
12.2 Washing and Drying Automatic levels
1. Tap on the Droogtegraad/Niveau séchage button repeatedly until the display shows the required dryness level. The indicators in the display illuminate accordingly:

a. items;

Iron dry: for cotton

b.

Cupboard dry: for

cotton and synthetic items;

c.

Extra dry: for cotton

items.

The time value on the display is the

duration of both cycles washing and

drying, calculated on a default load

size.

To have a good drying by using less energy and in a shorter time, the appliance does not let you set a too low spin speed for the items to be washed and dried.
2. Touch button Start/Pauze/Départ/ Pause to start the programme. The PROSENSE estimation starts.

In the display the door locked indicator goes on, the indicator of the running phase starts flashing. The display also shows the remaining programme time.

12.3 Washing and Timed Drying
1. Tap on the button Droogtijd/Minuterie repeatedly to set the desired time value (see the “Timed drying” table

ENGLISH 35

the “Programmes” chapter). The drying level indicator goes off and the
indicator comes on. The minimum timed drying is 10 minutes. Each time you tap on this button the time value increases by 5 minutes. The display shows the set new time value. 2. Touch the Start/Pauze/Départ/Pause
to start the programme. The ProSense estimation starts.
In the display the door locked indicator comes on and the indicator of the running phase starts flashing. The display also shows the remaining programme time.
12.4 At the end of the drying programme
· The appliance stops automatically. · The acoustic signals operate (if they
are active).
· In the display comes on. · The indicator of button Start/Pauze/
Départ/Pause goes off. The door
locked goes off

· Press the button Aan/Uit/Marche/Arrêt for some seconds to deactivate the appliance.
After some minutes from the end of the programme, the energy saving function deactivates the appliance automatically.
1. Remove the laundry from the appliance.
2. Make sure that the drum is empty.
After drying phase, clean the drum, the seal and the inside of the door with a wet cloth.
The indicator appears on the display to remind you to clean the air filter (refer to ‘Cleaning the air filters’ in ‘Care and cleaning’ chapter).

13. DAILY USE – DRYING ONLY

WARNING! Refer to Safety chapters.
This appliance is an automatic washer dryer.
13.1 Preparation to drying
1. Press the Aan/Uit/Marche/Arrêt button for some seconds to activate the appliance.
With a drying-only programme the display does not show the maximum load and the ProSense estimation is deactivated. 2. Load the laundry one item at a time. 3. Turn the programme dial to the programme suitable for the items to dry. 4. Tap on the MODUS/MODE button twice to exclude washing and perform drying only. The Drogen/ Séchage indicator is on. The

indicators and on the display.

appear

When drying a big amount of laundry, to have good drying performances, make sure that the laundry itself is not rolled up and that is uniformly distributed in the drum.

13.2 Drying – Automatic levels
1. Tap on the Droogtegraad/Niveau séchage button repeatedly until the display shows the required dryness level. The indicators in the display illuminate accordingly:

a. items;

Iron dry: for cotton

36 www.aeg.com

b.

Cupboard dry: for

cotton and synthetic items;

c.

Extra dry: for cotton

items.

The display shows the drying

programme duration.

To have a good drying by using less energy and in a shorter time, the appliance does not let you set a too low spin speed for the items to be washed and dried.
2. Touch button Start/Pauze/Départ/ Pause to start the programme.

In the display the door locked indicator goes on, the indicator of the running phase starts flashing. The display also shows the remaining programme time.

13.3 Timed Drying
1. Tap on the button Droogtijd/Minuterie repeatedly to set the desired time value (see the “Timed drying” table the “Programmes” chapter). The drying level indicator goes off and the
indicator comes on. The minimum timed drying is 15 minutes. Each time you tap on this button the time value increases by 5 minutes. The display shows the set new time value. 2. Touch the Start/Pauze/Départ/Pause
to start the programme.
In the display the door locked indicator comes on and the indicator of the running phase starts flashing.

14. FLUFF IN THE FABRICS

During the washing and/or drying phase, some types of fabric, (sponge, wool, sweatshirt) could release fluff.
The released fluff could stick to the fabrics during the next cycle.
This inconvenient increases with technical fabrics.
To prevent the fluff in your laundry:

The display also shows the remaining programme time.
13.4 At the end of the drying programme
· The appliance stops automatically. · The acoustic signals operate (if they
are active). · In the display comes on. · The indicator of button Start/Pauze/
Départ/Pause goes off. The door locked goes off · Press the button Aan/Uit/Marche/Arrêt for some seconds to deactivate the appliance.
After some minutes from the end of the programme, the energy saving function deactivates the appliance automatically. 1. Remove the laundry from the appliance. 2. Make sure that the drum is empty.
After drying phase, clean the drum, the seal and the inside of the door with a wet cloth. The indicator appears on the display to remind you to clean the air filter (refer to ‘Cleaning the air filters’ in ‘Care and cleaning’ chapter).
· Do not wash dark fabrics after you washed and dried light coloured fabrics (hand towel, wool, sweatshirt ) and the contrary.
· Dry this type of fabrics at open air when they are washed the first time.
· Clean the drain filter. · After the drying phase, clean the
empty drum, the gasket and the door with a wet cloth.

To remove the fluff inside the drum, proceed as follows: · Empty the drum. · Clean the drum, the gasket and the
door with a wet cloth. · Set the rinse programme. · Simultaneously press the
Centrifugeren/Essorage and the Tijd besparen/Rapide buttons until the
15. HINTS AND TIPS
WARNING! Refer to Safety chapters.
15.1 The laundry load
· Divide the laundry into: white, coloured, synthetics, delicates and wool.
· Follow the washing instructions on the laundry care labels.
· Do not wash white and coloured items together.
· Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first couple of times.
· Turn multilayered fabrics, wool and items with printed illustrations inside out.
· Pre-treat stubborn stains. · Wash stubborn stains with a special
detergent. · Be careful with curtains. Remove the
hooks and put the curtains in a washing bag or pillowcase. · A very small load can cause balance problems with the spin phase leading to excessive vibration. If this occurs: a. interrupt the programme and
open the door (refer to “Daily Use” chapter); b. manually redistribute the load so that the items are spaced evenly around the tub; c. press the Start/Pauze/Départ/ Pause button. The spin phase continues. · Button up pillowcases, close zippers, hooks and poppers. Tie up belts, cords, shoelaces, ribbons and any other loose elements. · Do not wash laundry without hems or with cuts. Use a washing bag to wash

ENGLISH 37
display shows CLE to activate the cleaning function. · Touch the Start/Pauze/Départ/Pause button to start the programme.
If the appliance is frequently used, carry out the CLE programme regularly.
small and/or delicate items (e.g. underwired bras, belts, tights, shoelaces, ribbons, etc. ).
· Empty pockets and unfold the items.
15.2 Stubborn stains
For some stains, water and detergent is not sufficient. We recommend that you pre-treat these stains before you put the items in the appliance. Special stain removers are available. Use the special stain remover that is applicable to the type of stain and fabric. Do not spray stain remover on garments near the appliance as it is corrosive to the plastic parts.

38 www.aeg.com

15.3 Detergent type and quantity

The choice of detergent and use of correct quantities not only affects your wash performance, but also helps to avoid waste and protect the environment:

· Use only detergents and other treatments specially made for washing machines. First, follow these generic rules: ­ powder detergents (also tablets and single-dose detergents) for all types of fabric, excluding delicate. Prefer powder detergents containing bleach for whites and laundry sanitization, ­ liquid detergents (also single-dose detergents) , preferably for low temperature wash programmes (60 °C max) for all types of fabric, or special ones for woollens only.
· The choice and quantity of detergent will depend on: type of fabric (delicates, woollens, cottons, etc), the colour of clothes, size of the load, degree of soiling, wash temperature and hardness of the water used.
· Follow the instructions that you find on packaging of the detergents or other treatments without exceeding

the indicated maximum level (

).

· Do not mix different types of

detergents.

· Use less detergent if:

­ you are washing a small load,

­ the laundry is lightly soiled,

­ there is large amounts of foam

during washing.

· When using detergent tabs or pods,

always put them inside the drum, not

in the detergent dispenser and follow

the manufacturer’s

recommendations .

Insufficient detergent may cause:

· unsatisfactory washing results, · the wash load to turn grey, · greasy clothes, · mould in the appliance.
Excessive detergent may cause: · sudsing, · reduced washing effect, · inadequate rinsing, · a greater impact for the environment.
15.4 Ecological hints
To save water, energy and to help protect the environment, we recommend that you follow these tips:
· Normally soiled laundry may be washed without prewash in order to save detergent, water and time (the environment is protected too!).
· Loading the appliance to the maximum capacity indicated for each programmes helps to reduce energy and water consumption.
· With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature.
· To use the correct quantity of detergent, refer to the quantity suggested by the detergent producer and check the water hardness of you domestic system. Refer to ‘Water hardness’.
· Set the maximum possible spin speed for the selected programme for saving energy during drying phase!
15.5 Water hardness
If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener.
To find out the water hardness in your area, contact your local water authority.
Use the correct quantity of water softener. Follow the instructions that you find on the packaging of the product.
15.6 Prepare the drying cycle
· Open the water tap.

· Check if the drain hose is connected properly. Refer to installation chapter for more information.
· For the maximum laundry load of the drying programmes, refer to the drying programmes table.
15.7 Items not suitable for drying
Do not set a drying programme for this laundry: · Synthetic curtains. · Pieces of clothing with metal inserts. · Nylon stockings. · Quilts. · Bed covers. · Duvets. · Sleeping bags. · Fabrics with residue of hair sprays,
nail solvents or similar. · Garments with foam-rubber or
materials similar to foam-rubber.
15.8 Garment labels
When you dry the laundry, obey the indications on the labels of the manufacturers:
· = The item can be tumble dried
· = The drying cycle is at high temperature
· = The drying cycle is at reduced temperature
· = The item can not be tumble dried.
15.9 Drying cycle duration
The drying time can change depending on:
16. CARE AND CLEANING
WARNING! Refer to Safety chapters.
16.1 Periodic cleaning schedule
Periodic cleaning helps to extend the life of your appliance.

ENGLISH 39
· speed of the last spin · dryness level · type of laundry · weight of the load
15.10 Additional drying
If, at the end of the drying programme, the laundry is still damp, set a short drying cycle again.
WARNING! To avoid creasing and shrinkage do not overdry the laundry.
15.11 General Tips
Refer to the «Timed drying» table to find the average drying times. Experience will help you to dry the laundry better. Take note of the duration of the cycles done before.
To avoid the static charge at the end of the drying cycle:
1. Use fabric conditioner in the washing cycle.
2. Use special fabric conditioner for tumble dryers.
3. Do not pour any detergent or softener before a drying cycle.
4. Do not dry rough and smooth textiles together, to avoid scorching on smooth garments.
5. Remove all objects from garment pockets, especially melting objects.
When the drying programme is completed remove the laundry in a short time.
After each cycle, keep the door and the detergent dispenser slightly ajar to get air circulation and dry the humidity inside the appliance: this will prevent mildew and odours.
If the appliance is not used for a long time: close the water tap and unplug the appliance.

40 www.aeg.com

Indicative periodic cleaning schedule:

Descaling

Twice a year

Maintenance wash Once a month

Clean door seal

Every two months

Clean drum

Every two months

Remove fluff inside Twice a month1) the drum

Clean detergent dis- Every two months penser

Primary air filter

After each cycle

Secondary air filter When the indicator flashes

Clean drain pump Twice a year filter

Clean the inlet hose Twice a year and the valve filter

1. Refer to ”Fluff in the fabrics” chapter.
   The following paragraphs explain how you should clean each part.

16.2 Removing foreign objects

Make sure that pockets are empty and all loose elements are tied up before running your cycle. Refer to “The laundry load” in “Hints and tips”.

Remove any foreign objects (such as metal clip, buttons, coins, etc) that you may find in the door seal, the filters and the drum. Refer to “Door seal with double lip trap”, “Cleaning the drum”, “Cleaning the drain pump” and “Cleaning the inlet hose and the valve filter” paragraphs. If necessary, please contact the Authorised Service Centre.

16.3 External cleaning
Clean the appliance with mild soap and warm water only. Fully dry all the surfaces.
Do not use a scouring pads or any scratching material.

CAUTION! Do not use alcohol, solvents or chemical products.
CAUTION! Do not clean the metal surfaces with chlorine-based detergent.
16.4 Descaling
If the water hardness in your area is high or moderate, we recommend that you use a water descaling product for washing machines.
Regularly examine the drum to check for limescale.
The regular detergents already contain water softening agents, but we recommend to run a cycle with empty drum and a descaling product occasionally.
Always follow the instructions that you find on the packaging of the product.
16.5 Maintenance wash
The repeated and prolonged use of low temperature programmes can cause detergent deposits, fluff residues, bacterial growth inside the drum and the tub. This could generate bad odours and mildew.
To eliminate these deposits and hygienize the inner part of the appliance, run a maintenance wash regularly (at least once a month):
1. Remove all laundry from the drum. 2. Run a cotton programme with the
highest temperature with a small quantity of powder detergent or, if available, run the Machine Clean programme.
16.6 Door seal
This appliance is designed with a self cleaning draining system, allowing light fluff fibers that fall off the clothes to be

drained out with the water. Regularly examine the seal. Coins, buttons, other small items can be recovered at the end of the cycle.
Clean it when needed, using ammonia cream cleanser agent without scratching the seal surface.
Always obey the instructions that you find on the packaging of the product.
16.7 Cleaning the drum
Regularly examine the drum to prevent unwanted deposits. Rust deposits in the drum may occur due to rusting foreign body in the washing or tap water containing iron. Clean the drum with special products for stainless steel.
Always follow the instructions that you find on the packaging of the product. Do not clean the drum with acidic descaling products, scouring products containing chlorine or iron or steel.
For a thorough clean: 1. Clean the drum with special products
for stainless steel. Always follow the instructions that you find on the packaging of the product.
2. Run a short cotton programme at high temperature with empty drum and with a small quantity of powder detergent or, if available, run the Machine Clean programme.

ENGLISH 41
16.8 Cleaning the detergent dispenser
To prevent possible deposits of dried detergent or clotted fabric softener and/or formation of mould in the detergent dispenser drawer, once in a while carry out the following cleaning procedure: 1. Open the drawer. Press the catch
downwards as indicated in the picture and pull it out.
1
2
2. Remove the top part of the additive compartment to aid cleaning. Make sure that all detergent residue is removed from the upper and lower part of the recess. Use a small brush to clean the recess.

42 www.aeg.com
3. Flush the detergent drawer out under running warm water to remove any traces of accumulated detergent. After cleaning, replace the top part in its position.
4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum.

2. Pull the primary air filter out.

16.9 Cleaning the air filters
The air filters collect the fluff. The fluff normally occurs when the clothes are dried in a washer-dryer.
· At the end of each drying cycle in the
display the indicator is on to advise to clean the primary air filter (see pictures from 1 to 5). The acoustic signal operates.
· Occasionally the indicator may flash to remind you that both air filters should be cleaned: the primary air filter and the secondary air filter (for secondary filter, see pictures from 6 to 8). The acoustic signal operates.
To have best drying performances clean the air filters regularly. Clogged filters make cycles longer and increase the energy consumption.
WARNING! Do not use water to clean the filters to avoid that plastic fibres flow in the water ambient. Throw the lint in a dustbin.
1. Push the hook to open the primary air filter.

3. Open the primary air filter cover by pulling it upwards.
PULL
4. Clean the primary air filter with your hand and, if necessary, with a vacuum cleaner. Throw the lint in a dustbin.
5. Close the primary air filter cover.

PULL

PULL

ENGLISH 43

L L U P

6. Pull the secondary filter out.

7. Clean the secondary air filter with your hand and, if necessary, with a vacuum cleaner. Throw the lint in a dustbin.
8. Reinsert the secondary air filter.

WARNING! The primary air filter recess must not be blocked by any object.
If you only wash the laundry with your washer-dryer, it is normal to find some humidity in the primary air filter.
16.10 Cleaning the drain pump
WARNING! Disconnect the mains plug from the mains socket.
Regularly check the drain pump filter and make sure that it is clean.
Clean the drain pump if: · The appliance does not drain the
water. · The drum does not turn. · The appliance makes an unusual
noise because of the blockage of the drain pump. · The display shows the alarm code
.

9. Reinsert the primary air filter and close it firmly.

44 www.aeg.com

WARNING! · Do not remove the filter
while the appliance operates. · Do not clean the pump if the water in the appliance is hot. Wait until the water cools down
WARNING! Each time you carry out the special programme CLE to remove fluff, clean the drain filter afterwards.
Proceed as follows to clean the pump:
1. Open the pump cover.

5. When the bowl is full of water, turn the filter back and empty the container.
6. Repeat the steps 4 and 5 until the water stops to flow out.
7. Turn the filter anti-clockwise to remove it.

2
1
2. Place a suitable bowl below the drain pump access to collect the water that flows out.
3. Open the chute downwards. Always keep a rag nearby to dry up any water spillages when removing the filter.

1 2
8. If it is necessary, remove fluff and objects from the filter recess.
9. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Centre.

4. Turn the filter 180 degrees in anticlockwise direction to open it, without removing. Let the water flow out.

10. Clean the filter under the water tap.

ENGLISH 45
12. Close the pump cover.

2

11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2
1

1
When you drain the water with the emergency drain procedure, you must activate the drain system again:
a. Put 2 litres of water in the main wash compartment of the detergent dispenser.
b. Start the programme to drain the water.

16.11 Cleaning the inlet hose filter and the valve filter

It could be necessary to clean the filters when: · The appliance does not fill with water. · The appliance takes long time to fills with water. · The indicator of the Start/Pauze/Départ/Pause button flashes and the display shows the
related alarm. Refer to ‘Troubleshooting’ chapter.

To clean the water inlet filters: 1

· Close the water tap. · Remove the water inlet hose from the
water tap. · Clean the filter in the inlet hose with a stiff
brush.

2

3

46 www.aeg.com

· Remove the inlet hose behind the appliance.

· Clean the filter in the valve with a stiff brush or a towel.

· Install again the inlet hose. Make sure that the couplings are tight to prevent leakages.
· Open the water tap.

45° 20°

16.12 Emergency drain
If the appliance cannot drain the water, carry out the same procedure, described in ‘Cleaning the drain pump’ paragraph. If necessary, clean the pump.
When you drain the water with the emergency drain procedure, you must activate the drain system again:
1. Put 2 litres of water in the main wash compartment of the detergent dispenser.
2. Start the programme to drain the water.
16.13 Frost precautions
If the appliance is installed in an area where the temperature can reach the values around 0° C or drop below,

remove the remaining water from the inlet hose and the drain pump.
1. Disconnect the mains plug from the mains socket.
2. Close the water tap. 3. Put the two ends of the inlet hose in
a container and let the water flow out of the hose. 4. Empty the drain pump. Refer to the emergency drain procedure. 5. When the drain pump is empty, install the inlet hose again.

ENGLISH 47
WARNING! Make sure that the temperature is higher than 5 °C and the water is flowing from the tap before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures.
17. TROUBLESHOOTING
WARNING! Refer to Safety chapters.
17.1 Alarm Codes and Possible failures
The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the tables).
WARNING! Deactivate the appliance before carrying out any check.

With some problems, the display shows an alarm code and the Start/Pauze/Départ/Pause button may flash continuously:

If the appliance is overloaded, remove some items from the drum and/or keep pressed the door while touching the Start/Pauze/Départ/Pause button until

the indicator below).

stops flashing (see the picture

Problem

Possible solution

48 www.aeg.com

·

The appliance does ·

not fill with water prop- erly.

· ·

·

·

Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the inlet hose has no kinks, damages or bends. Make sure that the connection of the water inlet hose is cor- rect. Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to ‘Care and cleaning’.

The appliance does not drain the water.

· Make sure that the sink spigot is not clogged. · Make sure that the drain hose has no kinks or bends. · Make sure that the drain filter is not clogged. Clean the filter, if
necessary. Refer to “Care and cleaning”. · Make sure that the connection of the drain hose is correct. · Set the drain programme if you set a programme without drain
phase. · Set the drain programme if you set an option which ends with
water in the tub.

The appliance door is open or not closed correctly.

· Make sure that the door is properly closed.

· The programme was not finished properly or the appliance

Internal fail. No com- munication between electronic elements of

·

stopped too early. Switch the appliance off and on again. If the alarm code appears again, contact the Authorised Serv- ice Centre.

the appliance.

The mains supply is unstable.

· Wait until mains supply is stable.

The anti-flood device is on.

· Disconnect the appliance and close the water tap. Contact the Authorised Service Centre.

: check the air fil- ter.

· Make sure that the air filter has been cleaned. · Make sure that the air filter is correctly inserted.

If the display shows other alarm codes, deactivate and activate the appliance. If the problem continues, contact the Authorised Service Centre. In case of different problem with the washing machine check the table below for possible solutions.

ENGLISH 49

Problem

Possible solution

· Make sure that the mains plug is connected to the mains

socket.

· Make sure that the appliance door is closed.

· Make sure that there is no damaged fuse in the fuse box.

The programme does · Make sure that the Start/Pauze/Départ/Pause has been

not start.

touched.

· If the delay start is set, cancel the setting or wait for the end of

countdown.

· Deactivate the Child Lock function if it is on.

· Check the position of the knob on the selected programme.

The appliance fills with · Make sure that the drain hose is in the correct position. The

water and drains im-

hose may be positioned too low. Refer to “Installation instruc-

mediately.

tion”.

The spin phase does not operate or the washing cycle lasts longer than usual.

· Set the spin programme. · Make sure that the drain filter is not clogged. Clean the filter, if
necessary. Refer to “Care and cleaning”. · Adjust manually the items in the tub and start the spin phase
again. This problem may be caused by balance problems.

There is water on the floor.

· Make sure that the couplings of the water hoses are tight and there is not water leakages.
· Make sure that the water inlet hose and the drain hose have no damages.
· Make sure you use the correct detergent and the correct quantity of it.

You cannot open the appliance door.

· Make sure that a washing programme that ends with water in tub, has not been selected.
· Make sure that the washing programme is finished. · Set the drain or the spin programme if there is water in the
drum. · Make sure that the appliance receives electrical power. · This problem may be caused by a failure of the appliance.
Contact the Authorised Service Centre. If you need to open the door, please read carefully “Emergen- cy door opening”.

The appliance makes an unusual noise and vibrates.

· Make sure the levelling of the appliance is correct. Refer to “Installation instruction”.
· Make sure that the packaging and/or the transit bolts are re- moved. Refer to “Installation instruction”.
· Add more laundry in the drum. The load may be too small.

The programme dura- · The ProSense System is able to adjust the programme dura-

tion increases or de-

tion according to the type and the laundry load size. Refer to

creases during pro-

“The ProSense System load detection” in “Daily Use” chapter.

gramme execution.

50 www.aeg.com

Problem

Possible solution

The washing results are not satisfactory.

· Increase the detergent quantity or use a different detergent. · Use special products to remove the stubborn stains before
you wash the laundry. · Make sure that you set the correct temperature. · Decrease the laundry load.

Too much foam in the · Reduce the quantity of detergent or the number of tablets or drum during the wash- single-dose detergents. ing cycle.

After the washing cy- cle, there are some detergent residues in the dispenser drawer.

· Make sure that the flap is in the correct position (UP for pow- der detergent – DOWN for liquid detergent).
· Make sure you have used the detergent dispenser according the indications given in this user manual.

After a steam pro- gramme, garments are partially wet.

Make sure that the appliance is accurately levelled. Adjust the ap- pliance by raising or lowering the feet.

· Turn the water tap on.

· Make sure the air filters are not clogged. Check primary and

The appliance does

secondary air filters.

not dry or does not dry · Make sure the drain filter is not clogged.

correctly.

· Reduce the laundry load.

· Make sure you have set the correct cycle. if necessary, set

again a short drying time.

The drying cycle is too long.

· Make sure the air filters are properly cleaned. · Make sure your laundry load does not exceed the declared
load for the set programme. · Make sure that the room temperature is in the correct range.

The laundry is full of different colours fluff.

The fabrics washed in the previous cycle released fluff of a differ- ent colour: · The drying phase helps to eliminate some fluff. · Clean the clothes with a fluff remover. In case of an excessive amount of fluff in the drum refer to “Fluff in the fabrics” paragraph for more details.

After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the Authorised Service Centre. The necessary data for the service centre are on the rating plate.

17.2 Emergency door opening
In case of power failure or functioning failure the appliance door remains locked. The washing programme continues when the power is restored. If the door remains locked in case of

failure, it is possible to open it using the emergency unlock function.
Before opening the door:

CAUTION! Risk of burns! Make sure that the water temperature is not too high and the laundry is not hot. If necessary, wait until they cool down. CAUTION! Risk of injury! Make sure that the drum is not rotating. If necessary, wait until the drum stops rotating. Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain (refer to «Emergency drain» in «Care and cleaning» chapter). To open the door, proceed as follows:
18. CONSUMPTION VALUES
18.1 Introduction

ENGLISH 51
1. Press the Aan/Uit/Marche/Arrêt button to switch the appliance off.
2. Disconnect the mains plug from the mains socket.
3. Open the filter flap. 4. Pull the emergency unlock trigger
downward once. Pull it downward once again, keep it tensed and, in the meanwhile, open the appliance door.
5. Take out the laundry and then close the appliance door.
6. Close the filter flap.

See the web link www.theenergylabel.eu for detailed information about Energy Label.

The QR code on the energy label supplied with the appliance provides a web link to the information related to the performance of the appliance in the EU EPREL database. Keep the energy label for reference together with the user manual and all other documents provided with this appliance. It is also possible to find the same information in EPREL using the link https://eprel.ec.europa.eu and the model name and product number that you find on the rating plate of the appliance. Refer to ‘Product description’ chapter for the position of the rating plate.
18.2 Legend

kg

Laundry load.

hh:mm Programme duration.

52 www.aeg.com

kWh Litres %

Energy consumption.

°C

Temperature in the laundry.

Water consumption.

rpm Spin speed.

Remaining moisture at the end of the cycle. The higher is the spin speed, the higher is the noise and the lower is the remaining moisture at the end of washing cycle.

Values and programme duration may differ depending on different conditions (e.g. room temperature, water temperature and pressure, load size and type of laundry, supply voltage) and also if you change the default setting of a programme.

18.3 According to Commission Regulation Eu 2019/2023

Washing only
Eco 40-60 pro- gramme
Full load

kg

kWh Litres hh:mm

10

0.900 61.0 03:55

Half load

5

0.605 47.0 02:50

Quarter load

2.5

1. Maximum spin speed.

Wash and dry cycle

Eco 40-60 pro-

gramme and Cupboard dry

kg

level

Full load

6

0.200 38.0 02:30
kWh Litres hh:mm 3.000 55.0 09:40

Half load

3

1. Maximum spin speed.

1.795

Power consumption in different modes

Off (W)

0.50

43.0 05:35
Stand-by (W) 0.50

Time to Off/Standby mode is 15 minutes maximum.

% 52.00 52.00 54.00
% 0.00 0.00

°C

rpm1)

37.0 1551 33.0 1551 23.0 1551

°C

rpm1)

39.0 1551 35.0 1551

Delay start (W) 4.00

18.4 Common programmes Washing only
These values are indicative only.

ENGLISH 53

Programme

kg

kWh Litres hh:mm %

Katoen/Coton 2) 95°C
Katoen/Coton 60°C

10

2.900 90.0 04:05 44.00

10

1.700 85.0 03:50 44.00

Katoen/Coton 3) 20°C
Synthetica/ Synthétiques 40°C

10

0.350 85.0 03:00 44.00

4

0.800 55.0 02:15 35.00

Fijne was/Délicats 4) 2 30°C

0.400 60.0 01:05 35.00

Wol/Laine 30°C

1.5

0.300

65.0

01:05 30.00

1. Reference indicator of the spin speed. 2) Suitable for washing heavily soiled textiles. 3) Suitable for washing lightly soiled cottons, synthetic and mixed fabrics. 4) It also performs as quick washing cycle for lightly soiled laundry.

18.5 Common programmes Wash and dry

°C 85.0 55.0 20.0 40.0 30.0 30.0

rpm1) 1600 1600 1600 1200 1200 1200

These values are indicative only.

Programme

kg

kWh

Synthetica/ Synthétiques 40°C

4

2.050

1. Reference indicator of the spin speed.

Litres hh:mm 55.0 05:50

% 1.00

°C

rpm1)

40.0 1200

54 www.aeg.com

19. ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of

appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

www.aeg.com/shop

157061980-A-352022

References

• Welcome to AEG
• AEG - aeg.com
• Product Support | AEG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>