iMEX MR360 Machine Control Receiver Instruction Manual

June 10, 2024
imex

MACHINE CONTROL RECEIVER

MR360M

MACHINE CONTROL RECEIVER
MAGNET OR CLAMP MOUNT

INSTRUCTION MANUAL.

iMEX MR360 Machine Control Receiver A1

PRODUCT OVERVIEW

MR360 Machine control receiver is an indispensable accessory of rotating laser instrument. The two must be used together. This receiver detects the position of the laser signals transmitted by the rotating laser instrument. It provides quickly and precisely the horizontal and vertical references. This product is characterized by large-scale detecting window, 360° available laser beam receiving, High-bright LED display, low power consumption, good reliability and easy manipulation. It can be used with many different types of rotating laser instrument.

  1. ON/OFF
  2. Magnet base
  3. Indication window
  4. Receiving window
  5. Outer connecting socket

Charging indication LED Lighted: shows the instrument is charging
Extinguished: shows the instrument is not charging

  1. Upper laser indication LED (red) lighted means the laser line is above the zero-line.
  2. Laser zero indication LED (green) lighted means the laser line is level with the zero-line.
  3. Lower laser indication LED (red) lighted means the laser line is below the zero-line.

Power/ fine and coarse measuring switch button: turn power on/off & fine and coarse measuring switch.

DETECTING METHOD

This product can be used to detect any types of rotating laser instrument.

Short press button, each LED will blink in turn, which indicates the instrument can start detecting.

The detector is in coarse-detecting mode at the beginning of powering on.

Short press button once will enter into fine and coarse measuring switch.

Long press button, the LEDs will blink in turn from the center to both sides. The instrument will be off.

Note: pressing the button more than 1 second is long press, less than 1 second, is short press.

While the fine and coarse measuring switch, the LEDS shows as follows:

Short press button

Two LEDs outside will blink three times simultaneously indicates the instrument will be in coarse measuring mode
Short press button

Two LEDs inside will blink three times simultaneously means the instrument will be in fine measuring mode

THE LED’S INDICATION WHEN DETECTING AS FOLLOWS

LED’s all extinguish| The firs upper red LED blink quickly| The second upper red LED blink quickly| The green LED blink quickly| The first lower red LED blink quickly| The second lower red LED blink quickly| The signal LED blink slowly
---|---|---|---|---|---|---
| | | | | |
No laser line can detected| The laser line is higher| The laser line is higher| The laser line coincide with the zero-line| The laser line is lower| The laser line is lower| Memorizes the last receiving position and keep display (after removing the laser line)

Note: When at low voltage, the instrument will power off automatically. You need to charge the unit in case of this.

APPLICATION METHOD

Connect the MR360 to the 12V or 24V car storage battery by the offered cable.

Charge the inside rechargeable battery by the special 240 V charger, the charging time is 6 hours.

The MR360 is supplied with remote display, which can be connected to the receiver by the special cable. By installing the remote display inside the cabin this will enable you to view the indicating arrows directly rather than always focusing your eyes on the machine’s cutting edge, which makes it possible to locate the receiver higher than the cab to prevent laser beaming blocking and to ensure 360 degree reception.

MAINTENANCE
  1. Keep the instrument clean, particularly the detecting window. If detecting window is dusty, using a cloth gently clean.
  2. Avoid knocking, falling on the ground, being wet with water or heated by fire.
SPECIFICATIONS

SPECIFICATIONS

Receiving distance| 200m
Measuring accuracy| fine: ±3mm to ±12mm
course: ±5mm to ±25mm
Receiving range| (25cm) receiving window
Receiving angle| 360°full
Built-in power| 7.2V, 3500mAH Ni-MH battery-pack
Battery life| > 40 hours (built-in battery-pack)
Operating voltage| 12V±10% to 24V±10%
Charging time| 6 hours
Dimension| 376x80x149mm with magnet
376x120x205mm with clamp holder
Weight| 3.1kg
Operating temperature| -20°C to +50°C

PLAN_SET_LEVEL

Other Functions
  1. Memory function of the last received data and holding display.
  2. Outlet socket to connect with remote display
  3. Power off automatically at low voltage

Accessories and requirement

  1. Magnet bracket or clamp holder (at least 40mm circular pipe)
  2. Cable for connecting external power to 12V or 24V battery
  3. Connecting cable for LS707 remote display
  4. Input voltage of charger AC 90V to 240V

WWW.IMEXLASERS.COM

iM EX Lasers – part of the Position Partners Pty Ltd Group © 2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals