elo ET1902L 19-Inch LCD Desktop User Manual
- June 10, 2024
- elo
Table of Contents
- elo ET1902L 19-Inch LCD Desktop
- Product Information Elo Touch Solutions ET1902L, ET2202L, ET2402L,
- Product Usage Instructions
- Connector Panel
- Touch Monitor Connections
- Installing the Touch Technology Software Drivers
- Mounting
- Wall Mount
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
elo ET1902L 19-Inch LCD Desktop
Product Information Elo Touch Solutions ET1902L, ET2202L, ET2402L,
ET2702L
The Elo Touch Solutions monitors are projected-capacitive touch monitors that come in four different sizes: ET1902L, ET2202L, ET2402L, and ET2702L. These monitors have a 100 x 100 mm VESA FDMI-compliant counting for M4 screws on the rear of the monitor to mount them on walls. They have four peripheral ports, located atthe top, bottom, left, and right sides of the monitor, which can be used to mount an MSR (Magnetic Stripe Reader). The touch monitors can be connected to a video source using an HDMI or VGA video cable and a USB touch cable between the monitor’s USB connector and your PC’s USB port. They also have an audio output to connect to an audio source. The touch monitors come with a power adaptor that needs to be connected to a power source.
Product Usage Instructions
Unpacking the Touch Monitor
When you receive the Elo Touch Solutions monitor, unpack it carefully and
ensure that all the components are included.
- Touch monitor with stand
- Japanese-language regulatory information pamphlet
- Quick Install Guide
- VGA cable
- HDMI cable
- USB cable
- Audio cable
- Power brick
- Europe power cord
- North America power cord
- 3 x tie wraps
- EEI Label
- 2 x cable cover screws
Connector Panel
Use the cable tie-down points to tie down the cables with tie wraps. Loop the tie wraps through the cable tie-down points and around the cable to secure cable connections.
Note : Cable tie-down points can be used to tie down the cables with tie wraps. Simply loop the tie wraps through the cable tie-down points and around the cable to secure cable connections
Touch Monitor Connections
- Connect one end of the HDMI or VGA video cable to the monitor’s HDMI/VGA input connector and the other end to your HDMI/VGA video source. Tighten the video cable’s screws on the VGA connector for best performance.
- Connect the USB touch cable between the monitor’s USB connector and your PC’s USB port.
- Connect the audio cable between the monitor’s Audio Out and your audio source.
- Connect the power adaptor’s input connector to the power source. Connect the power adaptor’s DC output connector to the monitor’s input power jack.
- The touch monitor ships in an OFF state. Press the power button to turn it on.
Installing the Touch Technology Software Drivers
No additional drivers are required for your projected-capacitive touch monitor with Windows 7, 8, or 10 operating systems, as it will use the Windows HID drivers. If the monitor is used with the Windows XP operating system, follow the steps below to install the Windows XP touch driver:
- Visit www.elotouch.com/Support/Downloads/Driver/DriverDownload/Default.aspx
- Select the operating system from the Operating System drop-down menu.
- Select the technology from the Technologies drop-down menu.
- Download the driver version required for your touch monitor.
Mounting
Rear VESA Mount
A four-hole 100 x 100 mm mounting interface for M4 screws is provided on
the rear of the monitor. Remove the stand using a Phillips screwdriver to
access the mounting interface. The VESA FDMI-compliant counting is coded VESA
MIS-B, 75, C and VESA MIS-D, 100, C.
Base Mount
The VESA FDMI-compliant counting is coded VESA MIS-E, C. ET1902L & ET2202L
base mounting options and ET2402L & ET2702L base mounting options are shown in
the user manual. The VESA FDMI-compliant counting is coded VESA MIS-E, C.
ET1902L & ET2202L base mounting options are shown below.
ET2402L & ET2702L base mounting options shown below
Magnetic Stripe Reader (MSR) Installation (Optional)
To mount an MSR, remove one of the peripheral port covers with your
fingertips and install the MSR. Please refer to the MSR Quick Install Guide
(QIG) for set-up details. Your monitor comes with four pheripheral ports,
located at the top, bottom, left and right sides of the monitor. To mount an
MSR, remove one of the pheripheral port covers with your finger tips and
install the MSR as shown below. Please refer to the MSR Quick Install Guide
(QIG) for set-up details.
Wall Mount
- Mount the wall bracket to the wall using six fasteners appropriate for the type of wall material and following all applicable building code standards.
- Ensure the unit is mounted to a solid structure and surface, such as a support beam or wall.
- Attach the other bracket to the monitor using the four M4 screws included in the kit.
- Hang the monitor on the wall bracket and secure using two M3 screws included with the kit on the left and right side of the bracket.
Handles Installation (Optional)
Optional handles can be installed on 02 Series monitors, as shown below.
Please note that it is not recommended to use handles to carry the touch
monitor. Damage to the touch monitor will occur if the touch monitor is lifted
by the handles. Use handles only to adjust the tilt angle.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>