How to perform the 30 30 30 Hard reset for routers and modems Guide
- June 10, 2024
- Routers
Table of Contents
How to perform the 30 30 30 Hard reset for routers and modems
The term “30-30-30” is often used in reference to a hard reset procedure for routers and modems. It involves holding down the reset button on the device for 30 seconds while the power is on, then continuing to hold the button while turning off the power for another 30 seconds, and finally holding the button down for another 30 seconds while turning the power back on.
This procedure is intended to completely reset the device to its factory default settings, clearing any custom settings or configurations that may have been added. It can be useful in situations where the device is not functioning properly or has been misconfigured, and a reset is needed to restore it to a working state. However, it should be used with caution, as it will erase all custom configurations and settings, including any security settings or passwords.
How to use the reset button for 30 30 30
here are the steps to use the reset button for a 30-30-30 hard reset:
- Locate the reset button: The reset button is usually a small button located on the back or bottom of the router or modem. It may be labeled “Reset” or have a small circular arrow icon.
- Power on the device: Make sure the device is powered on and connected to a power source.
- Press and hold the reset button: Use a paperclip or similar object to press and hold the reset button for approximately 30 seconds.
- While still holding the reset button, unplug the device from the power source and continue to hold the reset button for another 30 seconds.
- While still holding the reset button, plug the device back into the power source and continue to hold the reset button for another 30 seconds.
- Release the reset button and wait for the device to reboot: Once you have held the reset button for a total of 90 seconds, release the button and wait for the device to reboot. This may take a few minutes, so be patient.
- Access the device: Once the device has finished rebooting, it will be restored to its factory default settings. You can now access the device using the default login credentials, which are typically printed on a label on the device or in the user manual.
Note: The 30-30-30 hard reset procedure is a more thorough reset method than a standard reset, and should only be used when necessary. It will erase all custom configurations and settings, so be sure to back up any important data or settings before performing this type of reset. The exact steps for using the reset button may vary depending on the model and brand of your router or modem, so be sure to consult the user manual or manufacturer’s website for specific instructions.
What is the difference between a reboot and a reset?
A reboot and a reset are two different actions that can be performed on electronic devices such as routers, modems, computers, and smartphones.
A reboot is simply the act of restarting the device. This means that the device will shut down all its processes and then restart them again from scratch. A reboot can be useful when a device is running slowly or when certain processes are not responding. Rebooting can help clear up any temporary issues that may be causing the device to malfunction.
A reset, on the other hand, is the act of returning the device to its original factory settings. This means that all custom configurations, settings, and data on the device will be erased, and the device will be restored to the way it was when it was first purchased. A reset is a more drastic step than a reboot and should only be performed when there is a serious issue with the device that cannot be resolved by other means.
In summary, a reboot is a simple restart of the device, while a reset is a more severe action that erases all custom configurations and data on the device.
What are the indicators that you should do a reboot or a reset?
Here are some indicators that you should perform a reboot or a reset on a device:
Reboot:
- The device is running slowly or not responding to commands.
- Certain processes or applications are not working as they should.
- The device is experiencing connectivity issues, such as slow or no internet connection.
- You have recently installed new software or updates and the device is not functioning properly.
Reset:
- The device is experiencing severe issues that cannot be resolved by a simple reboot.
- You have forgotten the login credentials or password for the device.
- You are selling or giving away the device and want to erase all personal data and configurations.
- The device has been infected with malware or a virus that cannot be removed by other means.
It’s important to note that performing a reset will erase all custom configurations and data on the device, so it should only be done as a last resort. Before performing a reset, it’s a good idea to try other troubleshooting steps, such as rebooting the device or seeking technical support from the manufacturer.
Why do routers require rebooting or resetting in the first place?
Routers are electronic devices that can experience issues and errors over time. Here are some reasons why routers may require rebooting or resetting:
- Memory leaks: Routers use memory to store data and run processes. Over time, memory leaks can occur, which means that memory is not released properly after a process is complete. This can cause the router to slow down or stop responding.
- Firmware updates: Routers require firmware updates to ensure they are functioning at their best. However, sometimes these updates can cause issues that require a reboot to resolve.
- Network congestion: If too many devices are connected to a router, it can cause network congestion, which can result in slow speeds or dropped connections. Rebooting the router can help clear up any congestion issues.
- Security issues: Routers can be vulnerable to security issues such as malware or hacking attempts. If a security issue is suspected, a reset may be necessary to remove any malicious software or to revert to the default settings to eliminate any security vulnerabilities.
- Configuration errors: Sometimes, configuration errors can cause issues with the router’s performance. Resetting the router can restore the default settings and allow for a fresh start in configuring the router.
In summary, routers require rebooting or resetting to resolve issues that may arise due to memory leaks, firmware updates, network congestion, security issues, or configuration errors. Rebooting or resetting the router can help clear up these issues and ensure the router is functioning properly.
FAQs
Will a hard reset erase all of my data?
Yes, a hard reset will erase all of the custom configurations and data on the router, including the login credentials and any settings you may have changed.
Do I need to reconfigure my router after a hard reset?
Yes, you will need to reconfigure your router after a hard reset, including setting up the Wi-Fi network name and password, and any other settings you may have customized.
How often should I perform a hard reset on my router?
You should only perform a hard reset on your router as a last resort, when all other troubleshooting steps have failed to resolve the issue. It is not necessary to perform a hard reset on a regular basis.
How long does it take to perform a hard reset on a router?
The process of performing a hard reset typically takes only a few minutes. However, the time it takes to reconfigure the router can vary depending on the complexity of the settings and the number of devices connected to the network.
Will a hard reset fix all router issues?
No, a hard reset will not fix all router issues. While it can resolve some issues related to memory leaks, firmware updates, network congestion, security issues, or configuration errors, it cannot fix issues related to faulty hardware or physical damage to the router.
How do I know if a hard reset has fixed my router issue?
After performing a hard reset and reconfiguring the router, you should test the device to see if the issue has been resolved. For example, check to see if the internet connection is working properly or if any error messages have disappeared.
What are the default usernames and passwords for my ASUS router?
The default usernames and passwords for ASUS routers depend on the model of the router. However, here are some of the most commonly used default login credentials:
- Username: admin, Password: admin
- Username: admin, Password: password
- Username: root, Password: admin
- Username: root, Password: password
- Username: admin, Password: 1234
What does the flashing light indicate / router light troubleshooting?
The flashing lights on a router can indicate different things depending on the model and manufacturer of the device. Here are some common meanings of flashing router lights:
- Power light flashing: This can indicate that there’s an issue with the power supply, or the device is booting up.
- Internet/WAN light flashing: This can indicate that the router is trying to establish a connection to the internet. If it continues to flash for an extended period, it could indicate an issue with the internet connection.
- LAN light flashing: This can indicate that there’s activity on the local network.
- Wi-Fi light flashing: This can indicate that the Wi-Fi radio is turned on and there’s activity on the wireless network.
- WPS light flashing: This indicates that the Wi-Fi Protected Setup feature is enabled and is waiting for a device to connect.
If you’re experiencing issues with your router, it’s always a good idea to check the router’s manual for specific troubleshooting steps. However, in general, if a light is flashing, it can indicate that the router is working properly, but may be experiencing an issue with connectivity or configuration.