Hotpoint H8 D94WB UK Condenser Tumble Dryer User Guide
- September 5, 2022
- Hotpoint
Table of Contents
Hotpoint H8 D94WB UK Condenser Tumble Dryer
CONTROL PANEL
- Programme selection knob
- On/Off button
- Start/Pause button Options buttons
- Gentle Power
- Crease Care
- Cycle End Signal
- Cycle Options (hold for Settings)
- Dryness Level
- Timed Drying
- Start Delay Navigation buttons and Key Lock
- UP
- DOWN
- CONFIRM OK (hold for Key Lock)
INDICATORS
Cycle phase: Drying – Cool Down – END End of Cycle
Empty water tank – Clean secondary filter – Clogged door filters
– Auto clean – Eco Monitor
Refer to Troubleshooting section: Failure call After-sales Service –
DEMO Demo Mode
FIRST TIME USE
When starting the appliance the first time, the control panel will
automatically show the set language menu. The UP and DOWN buttons are used to
show the languages available in the machine. Press the OK button to confirm.
The machine cannot be used without having selected the language. Make sure
that the water tank is correctly inserted. The dryer must be installed in a
room with a temperature ranging between 5°C and 35°C to ensure proper
operation. Before using the dryer make sure it has been in an upright position
for at least 6 hours.
DAILY USE
Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying cycle.
- remember to clean your filters after each drying cycle. Refer to the Care & Maintenance section.
- Plug the dryer into the power supply socket.
- Open the door and load garments; always refer to instructions on clothing labels and the max loads indicated in the programme section. Empty pockets. Make sure garments do not get caught between the door and/or the door filter. Do not load items that are dripping wet. Do not tumble dry large, very bulky items.
- Close the door.
- Press the “On/Off” button.
- Select the most suitable programme for the type of fabric in that load.
- Select the options, if necessary.
- Press the “Start/Pause” button to begin drying.
- At the end of the drying cycle, a buzzer will beep. An indicator on the control panel signals the end of the cycle. Pull the load out immediately to prevent the formation of creases on laundry.
- Turn the machine off by pressing the “On/Off” button, open the door and pull the clothing out. If the machine is not switched off manually, after about a quarter of an hour from the end of thecycle , the appliacycle , the appliance turns off automatically to save energy.
Note that some programme/option accords with “Crease Care” system. This means that for some hours, after the end of the drying cycle, the drum rotates at regular intervals to prevent the formation of creases. In case of power failure, it is necessary to press the “Start/Pause” button to restart the cycle
Eco Monitor
This indicator shows the energy consumption level according to
the programme and the options set. The consumption is
proportional to the lines on the display, by the eco monitor icon.
OPENING THE DOOR DURING THE CYCLE
Laundry can be checked while the drying cycle runs and any garments already
dry can be removed, while drying continues for the remaining items. After
closing the door, press the “Start/Pause” button to resume machine operation.
Keep the door closed until the cycle end to save time and energy.
NAVIGATION
The “UP” and “DOWN” buttons are used to navigate the available menus.
- Press the OK button to confirm the selection.
- Press the Option button at the symbol, where present on the display, to return to the previous screen. If no selection is confirmed, after about 2 minutes, the display return to the main screen.
SETTINGS
To access the Settings menu, press and hold the relevant button for a few seconds.
- Set language shows the available languages on the display.
- Sounds allows to enable or disable the sounds (some sounds, as warnings, will remain active anyway).
- Brightness allows to modify the display brightness.
- Factory Default allows to reset the default settings. After having selected the setting, press and hold the OK button for a few seconds.
MAX LOAD 9 Kg (Dry load)
CARE LABEL
Always check the care labels, especially when placing garments in the tumble
dryer for the fi rst time. Below are the most commonly used symbols:
- May be tumble dried.
- Do not tumble dry.
- Tumble dry – high heat.
- Tumble dry – low heat
PROGRAMS
The duration of these programs will depend on the size of the load, types of
textiles, the spin speed used in your washer and any extra options selected.
In machines equipped with display, the duration of the cycles is shown on the
control panel. The remaining time is constantly checked and adjusted during
the drying cycle to show the best possible estimate. Option to use – If all
your loads on Automatic Cycles are consistently less dry or more dry than you
would like, you may increase or decrease the dryness level using the specific
option.
Mixed kg 4
This programme is ideal for drying cotton and synthetic
fabrics together.
Eco Cotton kg Max
This is the most efficient programme in terms of energy consuption and is
suitable for drying normal wet cotton laundry. The values on the Energy Label
are based on this programme.
NOTE: for optimal energy efficiency, select “Cupboard Dry” using dryness
level option. To increase the dryness level, select “Extra Dry”.
Synthetics kg 4
For drying synthetic fabrics.
Daily kg 2
Ideal for drying garments of cotton blends or synthetics spun at high speed in
the washing machine.
Wool kg 1
Programme for drying wool clothes. It is advisable to turn the items inside
out before drying. If heavy edges remain damp, leavethem to dry naturally.
Silk kg 0.5
Gentle drying of silk garments.
Baby kg 2
A programme intended for drying newborns items (cotton and chenille), as well
as delicate items. Do not dry items with plastic coverings.
Duvet
Programme intended to dry bulky items, such as a single duvet.
More Cycles
- Bed & Bath kg Max
This programme is intended for drying cotton towels and
sheets.
Microfiber kg 2 Gentle drying for microfiber.
-
Cuddly Toys
This cycle preserves the appearance of cuddly toys, keeping them at their best. Remove all accessories before proceeding with drying. Each single piece must not exceed 600 gr. -
Fitness kg 4
For drying sports garments made of synthetics or cotton. -
Down Jacket kg 2
To dry down jackets, restoring their natural softness (2 jackets). -
Mats kg 3
To dry small bath or kitchen mats. Do not dry mats with plastic parts, as this could cause a fire hazard. -
Lingerie kg 2
To dry very delicate underwear. Close all hooks before drying. -
Shirts kg 3
This is a programme for cotton or cotton blend/synthetics shirts. -
Jeans kg 3
For drying sturdy cotton including denim trousers and jackets. -
Anti Allergy kg Max
This cycle has the “Allergy UK” approval of “The British Allergy Foundation” attesting the effective reduction and elimination of allergens. It can be used both with damp load (drying and treatment) and dry load (half load only). -
Pre- Iron
This cycle relaxes fibres, thus making ironing and folding easier. Suitable for small load of damp or dry cotton and cotton blend fabrics. Not for wet items.
Rapid 30′ kg 0.5
Ideal for drying cotton garments spun at high speed in the washing machine.
Refresh
A short programme suitable for refreshing fibres and garments through the
emission of fresh air. Do not use on wet items. It can be used on with any
load size but is more effective with small loads. It lasts about 20 minutes
OPTIONS
These buttons allow you to personalise the selected programme according to
personal requirements. Not all options are available for all programmes. Some
options may be incompatible with ones you have previously set; if so, you will
be alerted by the buzzer and/or blinking indicators. If the option is
available, the option indicator will stay on. The programme may retain some
options selected in previous drying cycles.
Dryness Level
Press the relevant button several times to obtain a different level of
residual moisture on your laundry. The display signals the level being
selected. After few seconds of inactivity, the display returns to the main
menu.
Iron Dry: very delicate drying. Items will be more easily ironed
immediately after the cycle.
Hanger Dry : a level intended for delicate garments ready to be hanged.
Cupboard Dry: the laundry is ready to be folded and put away.
EXTRA
Extra Dry: for laundry intended to be worn at the end of he cycle.
Timed Drying
This option is to manually set the drying time. Press the corresponding button
to set the required time for drying. An indicator on the control panel signals
the time being selected.
Start Delay
This option is for delaying the start of the cycle. Press the corresponding
button several times to find the required delay.
Once the max time is reached, the option is reset by pressing the button
again. An indicator on the control panel signals the time being selected.
After pressing the “Start/Pause” button, the machine signals the time
remaining to the start of the cycle. If the door is opened, press the
“Start/Pause button once the door has been closed.
Crease Care
This option add a crease treatment at the end of the cycle by means of a
periodic rotation of the drum (duration up to 10 hours). It is particularly
suitable when it is not possible to remove the laundry as soon as the drying
ends. If this option is used together with the Start Delay, the crease
treatment is added also in the Start Delay phase. This option remains in
memory if selected in the previous drying.
Gentle Power
At the end of the drying cycle laundry loses the wet film, which protects them
from wear and friction. When this option is activated the dryer performs anti-
stress drum movements that minimise the effects of fabric wear, meanwhile the
air circulation system provides a more even drying. The cycle time will be
extended when this option is turned on.
Key Lock
This option makes all machine controls inaccesible, except the “On/Off”
button. When the machine is on:
- to activate the option, keep the button pressed until the machines signals that the option has been enabled.
- to disable the option, keep the button pressed until the machine signals that the option has been disabled. This option remains in memory if selected in previous drying.
Cycle End Signal
This option activates a prolonged buzzer at the end of the cycle. Enable it if
you do not think you will hear the normal sound at the end of the cycle. After
having pressed the option button, it can be enabled or disabled using the UP
and DOWN buttons.
Quick guide
Press the OK button to confirm. This option remains in memory, if selected in
previous drying.
Cycle Option
This button provides access to the menu of options below. Scroll the options
with the “UP” and “DOWN” buttons and press the OK button to confirm the
selection.
-
Gentle
Enables a more gentle treatment of the laundry by reducing the drying temperature. -
Iron Ready
This option signals when the garments reach a dryness level suitable for ironing by means of the beeps and the display. Remove the garments to be ironed, close the door and press the Start/Pause button. The dryer goes on working until the remaining garments reach the selected dryness level.
CARE AND MAINTENANCE
WARNING: unplug the dryer during the cleaning and maintenance procedures.
Emptying the water tank after each cycle (see fig. A). Pull the container out of the dryer and empty it into a sink or other suitable drain, then place it back properly. Do not use the dryer without having inserted the container back in place.
Cleaning the primary door filter after each cycle (see fig. B).
Pull the primary door filter out and clean it by removing the lint from the filter surface under running water or using a vacuum cleaner.
Cleaning the secondary door filter when the relevant
indicator turns on
Pull the secondary door filter out and clean it in all its parts by washing it
under running water or using a vacuum cleaner. Clogged filters – clean both
door filters (see fig. B, fig. C). For optimal performance, dry the filters
before inserting them back in place. Do not use the dryer without having
inserted all filters back in place properly first. The filters are essential
parts for drying. They are intended to collect the lint formed during the
drying process. In case of clogged filters, the air flow inside the dryer
would be seriously affected: the drying time would be longer, the energy
consumption would increase and the dryer could be damaged. If these procedures
are not carried out properly, the dryer may not start.
Auto clean
The maintenance of the bottom filter of this model is automatic. The dryer
carries out cleaning when the sensors signal the need to do so. In this case,
the machine goes on working even when the drying cycle is completed. An
indicator on the control panel will signal the maintenance. Do not switch the
machine off during this phase.
Cleaning the tumble dryer
-
The external metal, plastic and rubber parts can be cleaned
with a damp cloth. -
Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
filters area, using a vacuum cleaner every so often. -
Do not use solvents or abrasives.
TRANSPORT AND HANDLING
Never lift the dryer by holding on to its top side.
- Unplug the dryer
- Remove the water from the water tank completely.
- Make sure that door and water tank are properly closed.
Power consumption
off-mode (Po) – Watts| 0.33
left-on mode (Pl) – Watts| 2.00
Programmes| kg| kWh| Minutes
Eco Cotton ***| 9| 1.64| 210
Eco Cotton| 4.5| 0.86| 120
Synthetics**| 4| 0.50| 78
This is the reference programme for the energy label and suitable to dry
normal wet cotton laundry. This is the most efficient programme in terms of
energy consumption for drying wet cotton laundry. (Standard/Default starting
configuration)
Heat Pump System
The heat pump contains fluorinated greenhouse gases,
contained in a hermetically sealed unit. This sealed unit contains
0.43 kg of the F gas R134a. GWP = 1430 (1 t CO2).
PRODUCT DESCRIPTION
- Water Tank (A)
- Air Intake grille
- Door filter: primary (B), secondary (C)
TROUBLESHOOTING EN
Before contacting the After-sales Service, refer to the table below. Often the
malfunctions are minor and can be solved in few
minutes
| Malfunction | Possible cause | Solution |
|---|---|---|
| The tumble dryer does not turn on. | The plug is not inserted into the socket. |
Insert the plug into the socket.
The plug is faulty.| Try to plug another appliance in the same socket. Do not
use connecting electrical devices to the socket, such as adapters or
extensions.
A power failure occurred.| Wait for the power supply to be restored and switch
the fuse on again if necessary.
The tumble dryer does not start.| The door has not been closed properly.|
Close the door.
A time delay was set to the start of the cycle.| For machines equipped with
this function: wait for the set delay to end or switch the machine off to
reset it. Refer to the Options section.
The “Start/Pause” button was not pressed in order to start the programme.|
Press the “Start/Pause” button.
The Key Lock function was enabled (for machines equipped with this option).|
Refer to the Options section. If Key Lock was selected, disable it. Switching
the machine off will not disable this option.
Garments are wet at cycle completion.| Small load.| The automatic programme
has not sensed the required final moisture so that the dryer completes the
programme and stops. If this happens simply select an additional short period
of drying or select Extra Dry option if available.
Large loads or heavier fabrics.| Dryness levels can be modified to the
specific dryness desired. Extra Dry is recommended for ready to wear items.
The drying times are very long.| An appropriate maintenance was not carried
out.| Refer to the Care & Maintenace section and perform the operations
described.
The programme, the time and/or the drying level set are not suitable for the
type and the amount of load inserted into the dryer.| Refer to Programmes and
Options sections to find the programme and options most suitable for the type
of load..
The garments are too wet.| Carry out a washing cycle with higher spin speed to
remove as much water as possible.
The dryer may be overloaded.| Refer to the Programmes section to check the max
load for each programme.
Room temperature.| The drying time may be longer if the room temperature falls
outside the 14–30°C range.
The programme did not end.| A power failure occurred might have occurred.| In
case of power failure, it is necessary to press the “Start/Pause” button to
restart the cycle
Note: some models are auto-cleaning and not equipped with bottom fi lter. Please refer to the Care & Maintenance section
References
- Hotpoint: Purchase Quality Home & Kitchen Appliances Online | HotPoint EU
- Whirlpool Docs
- Register | Whirlpool Europe
- Whirlpool Docs