SIGNATURE HARDWARE 440649 Foxfield Outdoor Post Lantern Instruction Manual
- June 10, 2024
- Signature Hardware
Table of Contents
SIGNATURE 440649 Foxfield Outdoor Post Lantern
Product Information: FOXFIELD SKU: 440649
The FOXFIELD product (SKU: 440649) is an electric fixture that requires
installation. The product comes with mounting hardware, wire connectors, and
screws. Before installing the product, it is recommended to consult a
professional if you are unfamiliar with installing electric fixtures.
Signature Hardware, the manufacturer, accepts no liability for any damage to
the faucet, plumbing, sink, counter top, or for personal injury during
installation. It is important to observe all local plumbing and building
codes.
The product has a black wire and a white wire that need to be connected to the
appropriate wires in your house. If your outlet has a ground wire (green or
bare copper), connect the fixture’s ground wire to it. Once the wires are
connected, tuck the wire connections neatly into the junction box.
The product also comes with a cage (A), a tube (B), and screws (D) that need
to be attached to each other to complete the installation.
Product Usage Instructions: FOXFIELD SKU: 440649
- Consult a professional if you are unfamiliar with installing electric fixtures.
- Unpack and inspect the product for shipping damage. If any damage is found, contact the Customer Relations team via live chat at www.signaturehardware.com or by emailing support@siganturehardware.com.
- Ensure that you have gathered all the required materials that are needed for the installation. The materials needed for installation include mounting hardware, wire connectors, and screws.
- Connect the black wire from the fixture to the supplied wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect fixture’s ground wire to it. Tuck the wire connections neatly into the junction box.
- Attach the Cage (A) to the Tube (B), and secure with Screws (D).
If you have any additional questions, please check out the Help Center at www.signaturehardware.com for product and warranty information, or contact the Customer Relations team through live chat or by emailing support@signaturehardware.com.
BEFORE YOU BEGIN
We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehard- ware.com or by emailing support @siganturehard-ware.com.
GETTING STARTED
Ensure that you have gathered all the required materials that are needed for
the installation.
FOR YOUR SAFETY
WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully, if you are unclear as to how to proceed, consult a qualified electrician.
TOOLS AND MATERIALS
INSTALLATION
-
Shut off the power at the circuit breaker and remove old fixture.
-
Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
-
CONNECTING THE WIRES
Connect the black wire from the fixture to the supplied wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect fixture’s ground wire to it. Tuck the wire connections neatly into the junction box.. -
Attach the Cage (A) to the Tube (B), and secure with Screws (D).
1.855.715.1800
signaturehardware.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>