SIGNATURE HARDWARE 440803 1-Light 15.75-Inch Polished Nickel Incandescent Flush Mount Light Owner’s Manual

June 10, 2024
Signature Hardware

440803 1-Light 15.75-Inch Polished Nickel Incandescent Flush Mount Light

SIGNATURE HARDWARE 440803 1-Light 15.75-Inch Polished Nickel
Incandescent Flush Mount Light Owner's Manual-product

Product Information: BANKLOFT SKU: 440803

The BANKLOFT product is an electric fixture that can be installed in a variety of settings. Please note that if you are unfamiliar with installing electric fixtures, we recommend consulting a professional. Observe all local plumbing and building codes to ensure safe installation.

The product comes with a set of tools and materials required for installation, which includes a light bulb, safety glasses, wire stripper, step ladder, Phillips and flathead screwdriver, wire cutters, electrical tape, and more. Please ensure that you have gathered all the required materials before proceeding with the installation process.

Product Usage Instructions

  1. Thread the nut (H) onto the nipple (I) and thread the nipple (I) through the saddle of shade (G) into the coupling (F). Slide the glass (J), the plastic washer (K), and the metal washer (L) onto the nipple (I), then secure with the nut (M). Slide the cap (N), the plastic washer (O), the crystal (P), the tube (Q), and the plastic washer (R) onto the nipple (I), then secure with the finial (S). Refer to FIG.1 above for reference.
  2. Thread the mounting screws (A) into the matching holes in the circular strap (B). Connect the white wire from the fixture to the white wire from the outlet box and the black wire from the fixture to the black wire from the outlet box. Cover the two wire connections using the two provided wire connectors. Wrap the two wire connections with electrical tape for more secure connection. Attach the grounding wire connections with electrical tape for more secure connection. Connect the copper ground wires from the fixture and from the outlet box to the ground screw on the mounting bar. Refer to FIG.2 above for reference.
  3. After the wires are connected, tuck them carefully inside the outlet box. Raise the canopy (D) allowing for the mounting screws (A) to protrude through the holes on the canopy (D), and secure with the ball nuts (E).
  4. If you have any additional questions, please check out our Help Center at www.signaturehardware.com for product and warranty information or contact us through live chat or by emailing support@signaturehardware.com.

Following these steps will ensure proper installation of the BANKLOFT product. Thank you for choosing Signature Hardware!

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehard- ware.com or by emailing support @siganturehard-ware.com.

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

FOR YOUR SAFETY

WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully, if you are unclear as to how to proceed, consult a qualified electrician.

TOOLS AND MATERIALS

SIGNATURE HARDWARE 440803 1-Light 15.75-Inch
Polished Nickel Incandescent Flush Mount Light Owner's Manual-
fig-1

INSTALLATION (FIG. 1)

  1. Thread the nut (H) onto the nipple (I) and thread the nipple (I) through the saddle of shade (G) into the coupling (F).
  2. Install llight bulbs (Not provided). Please do not exceed the maximum wattage capacity recommended on the socket.
  3. Slide the glass (J), the plastic washer (K) and the metal washer (L) onto the nipple (I), then secure with the nut (M).
  4. Slide the cap (N), the plastic washer (O), the crystal (P), the tube (Q) and the plastic washer (R) onto the nipple (I), then secure with the finial (S)

INSTALLATION (FIG. 2)

  1. Thread the mounting screws (A) into the matching holes in the circular strap (B).

  2. Secure circular strap (B) to the outlet box with outlet box screws (C).

  3. Connect the white wire from the fixture to the white wire from the outlet box and the black wire from the fixture to the black wire from the outlet box. Cover the two wire connections using the two provided wire connectors. Wrap the two wire connections with electrical tape for a more secure connection. Attach the grounding wire connections with electrical take for a more secure connection. Connect the copper ground wires from the fixture and from the outlet box to the ground screw on the mounting bar.
    Note: If you have electrical questions, consult your local electrical code for approved grounding methods.

  4. After wires are connected, tuck them carefully inside outlet box. Raise the canopy (D) allowing for the mounting screws (A) to protrude through the holes on canopy (D), and secure with the ball nuts (E)

1.855.715.1800

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Signature Hardware User Manuals

Related Manuals