Wallgate PSH-30 Secure Anti Ligature Hand Wash Dryer Instruction Manual

PSH-30 Secure Anti Ligature Hand Wash Dryer
Instruction Manual

PSH-30 Secure Anti Ligature Hand Wash Dryer

REVISION HISTORY

NOTES:

1. THE AIR GRILLE IS SLOTTED WITH THE SLOTS BEING 2 mm WIDTH. ONE WEB RUNS HORIZONTALLY TO REDUCE THE VERTICAL SLOT LENGTH
2. THE WATER AND SOAP NOZZLES HAVE 2mm OUTLET HOLES
3. THE WASTE GRILLE IS SLOTTED WITH THE SLOTS BEING 2 mm WIDTH. A WEB RUNS HORIZONTALLY TO REDUCE THE VERTICAL SLOT LENGTH.
4. THE HAND WASH FASCIA IS DESIGNED TO BE AS ANTI LIGATURE AS POSSIBLE WITH INTERNAL FACES ANGLED TO PREVENT ITEMS BEING JAMMED INTO THE BOWL.

NOTES:

1. THIS SHEET SHOWS THE CONTROL MODULE IN ITS STANDARD MOUNTING POSITION. THE CONTROL MODULE SITS BEHIND THE FASCIA FOR EASE OF CONNECTION
2. THE UNIT REQUIRES A WALL APERTURE OF 375 mm WIDTH BY 380 mm HEIGHT.
3. THE BASIN WASTE PIPE SHOULD BE CONNECTED TO A 1 ½” (40mm NOMINAL) DEEP SEAL WASTE TRAP (NOT SUPPLIED), A RUNNING TRAP IS NOT RECOMMENDED FOR THIS PRODUCT.
4. A WATER SUPPLY OF MINIMUM 1.0 Bar IS REQUIRED FOR CONNECTION TO THE WATER INLET ON THE FRONT OF THE UNIT. THE SUPPLY IS TO BE ROUTED THROUGH THE PROVIDED ISOLATOR VALVE.
5. THE CONTROL MODULE IS SUPPLIED WITH A 2 METER CABLE WITH EXPOSED ENDS FOR CONNECTION TO A 230v AC 50Hz 13Amp ELECTRICAL SUPPLY.
6. THE WATER HEATER SUPPLIED WITH 0.7M FLYING LEAD TO BE INSTALLED INTO A SEPARATE 230v AC 50Hz 13Amp FUSED SPUR AS PER ZIP ES3 MANUAL.
7. FULL INSTALLATION DETAILS CAN BE FOUND IN THE PSH_30 PRODUCT MANUAL SUPPLIED WITH THIS PRODUCT.
8. THE FASCIA CAN BE INSTALLED MOUNTED IN WALLS BETWEEN 13mm AND 175mm THICK. LONGER STUD BARS CAN BE PURCHASED FOR INSTALLATION INTO THICKER WALLS.
9. ENSURE 100mm CLEARANCE ABOVE THE AIR INTAKE TO ENSURE ADEQUATE AIRFLOW TO THE UNIT.

NOTES:

1. THIS SHEET SHOWS THE OVERALL DIMENSION FROM THE FRONT OF THE WALL TO THE REAR OF THE HEATER, DIMENSION X.
   ON A 13mm WALL X = 358 mm. (13mm WALL + 113 mm SPACER+ 232 mm CONTROL MODULE).
   ON A 175mm WALL X = 427 mm. (175mm WALL + 232 mm CONTROL MODULE).

NOTES:

1. THIS SHEET SHOWS A REMOTE MOUNTING POSITION FOR THE CONTROL MODULE WITH THE AIR CONNECTED TO THE FASCIA THROUGH AN LONG FLEXIBLE AIR HOSE. THIS FACILITY ALLOWS THE CONTROL MODULE TO BE MOUNTED IN A VARIETY OF DIFFERENT POSITIONS TO SUIT SITE REQUIREMENTS. (PLEASE NOTE: IF THIS INSTALLATION METHOD IS REQUIRED IT MUST BE REQUESTED WHEN THE ORDER IS PLACED SO THAT THE APPROPRIATE CONNECTIONS CAN BE SUPPLIED.)
2. THE FASCIA REQUIRES A WALL APERTURE OF 375mm WIDTH BY 380mm HEIGHT.
3. THE SOAP CONTAINER HANGS ON A BRACKET THAT CAN BE WALL MOUNTED TO SUIT REQUIREMENTS ON SITE.
4. THE BASIN WASTE PIPE SHOULD BE CONNECTED TO A 1 ½ ” (40mm NOMINAL) DEEP SEAL WASTE TRAP (NOT SUPPLIED), A RUNNING TRAP IS NOT RECOMMENDED FOR THIS PRODUCT.
5. A WATER SUPPLY OF MINIMUM 1.0 Bar IS REQUIRED FOR CONNECTION TO THE WATER INLET ON THE FRONT OF THE UNIT. THE SUPPLY IS TO BE ROUTED THROUGH THE PROVIDED ISOLATOR VALVE.
6. THE CONTROL MODULE IS SUPPLIED WITH A 2 METER CABLE WITH EXPOSED ENDS FOR CONNECTION TO A 230v AC 50Hz 13Amp ELECTRICAL SUPPLY.
7. THE WATER HEATER SUPPLIED WITH 0.7M FLYING LEAD TO BE INSTALLED INTO A SEPARATE 230v AC 50Hz 13Amp FUSED SPUR AS PER ZIP ES3 MANUAL.
8. FULL INSTALLATION DETAILS CAN BE FOUND IN THE PSH_30 PRODUCT MANUAL SUPPLIED WITH THIS PRODUCT.
9. THE FASCIA CAN CAN BE MOUNTED IN WALLS BETWEEN 13mm AND 175mm THICK. LONGER STUD BARS CAN BE PURCHASED FOR INSTALLATION INTO THICKER WALLS.
10. ENSURE 100mm CLEARANCE ABOVE THE AIR INTAKE TO ENSURE ADEQUATE AIRFLOW TO THE UNIT.

NOTE: THIS SHEET PROVIDES AN INSTALLATION OVERVIEW FOR REFERENCE ONLY. FOR FULL DETAILS REFER TO THE PRODUCT MANUAL.

INSTALL THE FASCIA INTO WALL

INSTALL HOSES AND CABLES TO FASCIA

FIX ENGINE TO MOUNTING BRACKETS
ADDITIONAL SPACE BRACKETS ARE PROVIDED FOR WALLS LESS THAN 120 mm THICK

CONNECT HOSES AND CABLES TO ENGINE

| TITLE: PSH-30 FASCIA AND
ENGINE INSTALLATION
Drg No:
INS-PSH-30
Model/Client/Project:| MATERIAL:
FINISH:| Limits: (unless stated)
± 0.25 mm (sheet metal)
± 0.10 mm (machined)
± 2.00 mm (pattern)
± 5.00 mm (moulded)| All dimensions in mm,
All angles 90~(unless stated)
SCALE: NTS
---|---|---|---|---

© 2022 Copyright
THIS DRAWING IS THE PROPERTY OF WALL GATE LIMITED AND IS ISSUED ON THE STRICT UNDERSTANDING THAT THE INFORMATION CONTAINED WILL NOT BE REPRODUCED, COPIED OR USED WITHOUT PRIOR AGREEMENT OF WALL GATE LTD.

t: +44 (0) 1722 744 594
f: +44 (0) 1722 742 096
e: sales@wallgate.com
w: www.wallgate.com
Company Reg No. 156022

References

• Commercial Washrooms & Specialist Applications - Anti-ligature Sanitaryware | Wallgate

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>