Evolveo DET-BT1 Detective BT1 IP Camera Owner’s Manual
- June 10, 2024
- Evolveo
Table of Contents
Evolveo DET-BT1 Detective BT1 IP Camera
WHAT’S INCLUDED
PRODUCT OVERVIEW
- Microphone
- Lens
- Infrared LEDs
- Indication LED
- PIR sensor
- USB-C charging port
- ON/OFF button
- Speaker
- Console port
ADDING A SPARE CAMERA
Switching on the camera
After removing the screws at the bottom of the camera, remove the cover and
long press the button at the bottom of the camera until you hear the music
prompt.
A red light indicates that the start-up was successful. Remark: Don’t forget
to put the cover back on after starting.
How to pair the camera with HomeBase
-
Connect HomeBase to a power source and to the network.
-
Long press the top “SYNC” button on the HomeBase until the yellow light starts flashing and turns on. A voice prompt will announce the start of pairing.
-
Press the ON/OFF button on the bottom of the camera three times . The red and blue LEDs will flash alternately.
-
A voice prompt from HomeBase notifies you that the pairing was successful.
Warning: The cameras and HomeBase were paired before delivery. Only replacement cameras need to be added manually.
CHARGING THE CAMERA
Remark: When charging the camera, remove the back cover by unscrewing the bottom screw of the camera. Once fully charged, the back cover needs to be put back on the camera. Use the supplied USB Type-C charging cable to connect your device, connect the cable to the camera and HomeBase for battery charging.
| LED Challenge | Blue LED flashes when charging |
|---|
Blue LED lights up when fully charged
Charging time| 10 hours (minimum battery charge)
The camera standby time varies according to the number of alarms and wake-ups per day. After a full charge it can be used for 3-4 months. This value is calculated on 10 wake-ups per day and 10 seconds of recording.
CAMERA INSTALLATION
Wireless Signal Testing
To find out where to install the camera, you need to test the strength of the wireless signal.
- To test the strength of the wireless signal, open the live preview in the app and take it and your mobile phone to the location where you want to install the camera.
- If the wireless signal is not stable, move the camera closer to the HomeBase.
Locating the installation site
Hang the camera 1.5-2m above the ground. This height maximizes the detection
range of the camera’s motion sensor.
Warning!: Do not place the camera in direct sunlight. The PIR sensor will
then not detect motion!
Installing the camera
The camera can be installed indoors or outdoors.
-
Attach a drilling template to the place where you will place the camera.
-
Align the camera mount port with the bracket and then snap it into the bracket, push it in until you hear a click, the camera is properly attached and you can adjust the camera angle via the live preview in the Smartlife app.
-
To detach the camera from the mounting bracket, press and hold the clip on the bracket to remove it.
The warranty does NOT cover:
-
* Using the device for purposes other than those for which it is intended,- Installing firmware other than that installed on the device.
- Electrical or mechanical damage caused by improper use.
- Damage caused by natural influences such as water, fire, static electricity, power fluctuations, etc.
- Damage caused by repairs carried out by an unqualified person.
- Illegible serial number
- Battery capacity will decrease after 6 months of use (6 month battery life guarantee)
Disposal
The crossed-out container symbol on the product, in the accompanying
documentation or on the packaging means that all electrical and electronic
equipment, batteries and accumulators in the European Union must be disposed
of as separated waste at the end of their life. These products must not be
disposed of as unsorted municipal waste.
DECLARATION OF CONFORMITY
Abacus Electric, s.r.o. hereby declares that the EVOLVEO SEA DET-BT1 meets the
requirements of the standards and regulations applicable to this type of
equipment. The full text of the Declaration of Conformity can be found at
http://ftp.evolveo.com/ce/.
- Importer / Importer / Importer / Importer
- Abacus Electric, s.r.o.
- Planá 2, 370 01, Czech Republic
- Producer / Producer / Gyártó
- Naxya Limited
- No. 5, 17/F, Strand 50, 50 Bonham Strand, Sheung Wan, Hongkong
- Made in China
- Copyright © Abacus Electric, s.r.o.
- www.facebook.com/EvolveoCZ
- All rights reserved. Product appearance and technical specifications are subject to change without notice
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>