PLT SOLUTIONS Wattage Color Selectable LED Vapor Tight Undercabinet Fixture Instruction Manual
- June 10, 2024
- PLT SOLUTIONS
Table of Contents
PLT SOLUTIONS Wattage Color Selectable LED Vapor Tight Undercabinet
Fixture
Product Information
LED Under Cabinet Fixture
The LED Under Cabinet Fixture is a lighting solution designed to improve the
visibility and ambiance of any area with cabinets. It is easy to install and
comes with safety instructions to ensure that it is set up correctly. The
fixture is equipped with a CCT selector switch that allows you to pick your
preferred color temperature.
Product Usage Instructions
LED Under Cabinet Fixture
- Before installation, make sure that you have all the necessary tools and equipment.
- Locate the desired location for the fixture and mark the keyhole slots.
- Remove the lens and LED driver cover from the luminaire.
- Screw in the mounting screws, leaving space for the channel body. Slide the channel over the mounting screws. Lift and shift the channel into position and tighten the screws.
- Make connections from the incoming power wires to the driver input power wires. Position the junction box mounting holes on the luminaire over the junction box and secure.
- Reattach the LED driver cover assembly to the luminaire housing, and then press the cover back until it is retained by the slots.
- Reattach the lens onto the luminaire housing.
- Turn on the power to confirm that the fixture is working properly.
- Select the desired color temperature by sliding the CCT selector switch to the appropriate setting.
It is important to note that if you encounter any problems during installation or usage, contact the manufacturer for further information or assistance.
SAFETY INSTRUCTIONS
WARNING
-
Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
-
To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards, read all warnings and instructions included with and on the fixture box and all fixture labels.
-
Proper grounding is required to ensure safety.
-
Power must be turned off at the breaker before installation or maintenance.
-
Installation, service, and maintenance of luminaires should be performed by a qualified licensed electrician.
-
Wear gloves and eye protection at all times while installing, servicing, or performing maintenance on the luminaire, and avoid direct eye exposure to the light source while it is on.
-
Do not install damaged product. Inspect luminaire for damage that may have occurred during transit. If damaged, contact the manufacturer immediately.
-
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, contact the manufacturer.
-
Install this product in accordance with country, regional and local laws and regulations.
-
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
-
Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
-
Account for small parts and destroy packing material, as these may be hazardous to children.
-
Risk of burn. Disconnect power and allow fixture to cool before changing/handing fixture.
CAUTION
- Verify the supply voltage is correct by comparing it with the luminaire label information.
- All wiring connections should be capped with UL approved wire connectors.
- Green ground screw provided is in proper location. Do not relocate.
- Use minimum 90°C supply conductors.
NOTICE
- Specifications and dimensions are subject to change without notice.
Installation Instructions
Wall or Under Cabinet Mounting – No Junction Box
- Carefully take out the product from the box. Remove the round knock-out in the luminaire housing that is nearest the location of incoming power wires.
- Remove the lens and the LED driver cover from the luminaire.
- Position the luminaire housing in the desired location, and then mark and drill mounting holes at the narrow ends of the keyhole slots. Screw in the mounting screws, leaving space for the channel body. Slide the channel over the mounting screws. Lift and shift the channel into position and tighten the screws.
- Make connections from the incoming power wires to the driver input power wires.
- Reattach the LED driver cover assembly to the luminaire housing, and then press the cover back until it is retained by the slots.
- Reattach the lens onto the luminaire housing.
- Turn on the power to confirm that the fixture is working properly. You can select the desired color temperature by sliding the CCT selector switch to the appropriate setting.
Wall or Under Cabinet Mounting – With Junction Box
- Carefully take out the product from the box. Remove the center knock-out from the back of the luminaire.
- Remove the lens and the LED driver cover from the luminaire.
- After considering Item 4 below, position the luminaire housing in the desired location, and then mark and drill mounting holes at the narrow ends of the keyhole slots. Screw in the mounting screws, leaving space for the channel body. Slide the channel over the mounting screws. Lift and shift the channel into position and tighten the screws.
- Make connections from the incoming power wires to the driver input power wires. Position the junction box mounting holes on the luminaire over the junction box and secure.
- Reattach the LED driver cover assembly to the luminaire housing, and then press the cover back until it is retained by the slots.
- Reattach the lens onto the luminaire housing.
- Turn on the power to confirm that the fixture is working properly. You can select the desired color temperature by sliding the CCT selector switch to the appropriate setting.
Wiring Diagram
972-535-0926 | pltsolutions.com | ver 072022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>