speco technologies O4iT1M Outdoor Network Dome Camera User Guide
- June 10, 2024
- speco technologies
Table of Contents
Speco technologies O4iT1M Outdoor Network Dome Camera
Product Information
The O4iT1M is a network camera designed for indoor or outdoor use. It comes with an Ethernet connector, audio input connector, power connector, mounting base, fixed screw, microphone, micro SD card slot, reset button, and optional waterproof connector. The camera requires a 12VDC Class 2 power supply or can be powered through a PoE switch or injector. It has a CMOS sensor that can be damaged by exposure to electromagnetic radiation or improper handling during installation.
Product Usage Instructions
- Before installation, check the package to ensure all components are included. Contact Speco customer service if anything is broken or missing.
- Install the camera in a cool, dry place away from direct sunlight and heat sources. Do not install in extreme temperature conditions.
- Use only a certified/listed 12VDC Class 2 power supply to avoid device damage.
- The product must be grounded to reduce the risk of electric shock.
- Do not connect two power supplying sources to the device at the same time.
- Avoid heavy stress, violent vibration, and exposure to water during transportation, storage, and installation.
- The camera should be installed by qualified personnel only to prevent unauthorized changes or modifications that could void the warranty.
- Shut down the device and unplug the power cable before performing maintenance work.
- Do not touch the CMOS sensor optic component. Clean the lens surface with a blower or dry soft cloth.
- Do not block any ventilation openings or allow water and liquid intrusion into the camera.
- Connect the network cable to the Ethernet connector and crimp it with an RJ45 connector.
- If installing outdoors, use the optional waterproof connector to prevent water damage.
- If using a PoE switch or injector, a DC12V power supply is not required.
- If the camera fails or requires repairs, contact Speco Technologies Tech Support at 1-800-645-5516.
Welcome
Thank you for purchasing this network camera!
This owner’s manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for
future reference. Should you require any technical assistance, contact Speco
Technologies Tech Support at
1-800-645-5516
Important Safeguards and Warning
Electrical safety
All installation and operation here should conform to local electrical safety
codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the
same time; it may result in device damage! The product must be grounded to
reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical
shock.
Environment
Heavy stress, violent vibration or exposure to water is not allowed during
transportation, storage and installation.
This product should be installed in a cool, dry place away from direct
sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result
in CMOS sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin
any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean
the dust on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust,
use a cloth dampened with a small quantity of neutral detergent. Finally use
the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure.
Improper enclosure cleaning (such as using cloth) may result in poor IR
functionality and/or IR reflection. The grounding holes of the product are
recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an optical device, please don’t touch or wipe cover surface
directly during installation and use, please refer to the following methods if
dirt is found:
Stained with dirt: Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint: Use oil-free cotton cloth or paper soaked
with alcohol or detergent to wipe from the lens center outward. Change the
cloth and wipe several times if it is not clean enough.
Warning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice.
Speco Technologies reserves the right to modify these without notice and
without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are
included. Contact your rep or Speco customer service department immediately if
something is broken or missing in the package.
Package
Overview
- Ethernet connector
- Audio input connector
- Power connector
- Mounting base
- Fixed screw
- Microphone
- Micro SD card slot
- Reset
- It is recommended to install the water-proof connector for outdoor installations.
- DC 12V power supply is not required if a PoE switch or injector is used to power the camera.
Connecting Network Cable
- Loosen the nut from the main element.
- Run the network cable (without RJ 45 connector) through both elements. Then crimp the cable with RJ 45 connector.
- Connect the cable to the water-proof connector. Then tighten the nut and the main cover.
Installation
Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera and the junction box.
-
Open the mounting base and the upper cover of the junction box.
-
Attach the drill template of the junction box to the place where you want to install the junction box and then rill the screw hole and calbe hole on the wall according to the drill template.
-
Install junction box onto the wall by using the screws provided.
-
Loosen the fixed screw to disassemble the camera. Then remove the cover from the dome to insert the SD card. After that, install the cover back to the dome and fix it firmly with the screws. (Note that the cover should not be installed unevenly .)
-
Fasten the camera onto the junction box.
-
Route the cables through the cable hole and connect the cables. Then reinstall the upper cover onto the junction box.
-
Adjust the camera to obtain an optimum angle. Before adjustment, preview the image of the camera on a monitor. After that, tighten the fixed screw to finish the installation.
Web Operation and Login
IP Scanner can search for the device on the local network.
Operation
-
Make sure that the camera and the PC are connected to the same local network. The camera is set to DHCP by default.
-
Install IP Scanner from the CD and run it after installation. Or download from https://www.specotech.com/ip-scanner/
-
In the device list, you can view the IP address, model number, and MAC address of each device. Select the applicable device and double click to open up the web viewer. You can also manually enter the IP address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and password is 1234. After logging in, follow directions to install applicable plugins if prompted.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>