speco technologies O4VT1N 4MP WDR Turret IP Camera User Guide
- June 10, 2024
- speco technologies
Table of Contents
O4VT1N 4MP WDR Turret IP Camera
Product Information
The O4VT1N is a network camera designed for indoor and outdoor use. It has an Ethernet connector, audio input connector, power connector, mounting base, microphone, micro SD card slot, and reset button. The camera can be powered through a certified/listed 12VDC Class 2 power supply or a PoE switch or injector. The camera is also equipped with a water-proof connector for outdoor use. It is important to follow the electrical safety guidelines and ensure that the camera is properly grounded to reduce the risk of electric shock. The camera should be installed in a cool, dry place away from direct sunlight and heat sources.
Product Usage Instructions
- Before installation, check that all components are included in the package. Contact Speco customer service if something is missing or broken.
- Follow local electrical safety codes and use a certified/listed 12VDC Class 2 power supply or a PoE switch or injector to power the camera. Do not connect two power supplying sources to the device at the same time as it may result in device damage.
- Install the camera in a cool, dry place away from direct sunlight and heat sources. Use the mounting base and fixed screw to secure the camera in place.
- If installing the camera outdoors, use the water-proof connector to connect the network cable and tighten the nut and main cover.
- Use a blower to clean the dust on the lens surface and always use a dry soft cloth to clean the device. Do not touch the CMOS sensor optic component.
- If performing any maintenance work, shut down the device and unplug the power cable before starting.
- Do not expose the camera to extreme temperature conditions or electromagnetic radiation as it may result in CMOS sensor failure.
- Do not block any ventilation openings and do not allow water or liquid intrusion into the camera.
- All examination and repair work should be done by qualified personnel only. Any unauthorized changes or modifications could void the warranty.
For additional technical assistance, contact Speco Technologies Tech Support at 1-800-645-5516.
Welcome
Thank you for purchasing this network camera! This owner’s manual is designed
to be a reference tool for your system. Please read this manual carefully
before operating the unit and retain it for future reference. Should you
require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
Important Safeguards and Warning
Electrical safety
All installation and operation here should conform to local electrical safety
codes. Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at
the same time; it may result in device damage! The product must be grounded to
reduce the risk of electric shock. Improper handling and/or installation could
run the risk of fire or electrical shock.
Environment
- Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and installation.
- This product should be installed in a cool, dry place away from direct sunlight and heat sources.
- Do not install the product in extreme temperature conditions.
- Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure.
- Do not block any ventilation openings.
- Do not allow water and liquid intrusion into the camera.
Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin
any maintenance work. Do not touch the CMOS sensor optic component. You can
use a blower to clean the dust on the lens surface. Always use the dry soft
cloth to clean the device. If there is too much dust, use a cloth dampened
with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device. Please use a professional optical cleaning method to clean the
enclosure. Improper enclosure cleaning (such as using cloth) may result in
poor IR functionality and/or IR reflection. The grounding holes of the product
are recommended to be grounded to further enhance the reliability of the
camera.
Dome cover is an optical device, please don’t touch or wipe cover surface
directly during installation and use, please refer to the following methods if
dirt is found:
Stained with dirt: Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint: Use oil-free cotton cloth or paper soaked
with alcohol or detergent to wipe from the lens center outward. Change the
cloth and wipe several times if it is not clean enough.
Warning
This camera should be installed by qualified personnel only. All the examination and repair work should be done by qualified personnel. Any unauthorized changes or modifications could void the warranty.
Statement
his guide is for reference only. Product, manuals and specifications may be
modified without prior notice. Speco Technologies reserves the right to modify
these without notice and without incurring any obligation. Speco Technologies
is not liable for any loss caused by improper operation.
Note: Before installation, check the package and make sure that all
components are included. Contact your rep or Speco customer service department
immediately if something is broken or missing in the package.
Package
Overview
- Ethernet connector
- Audio input connector
- Power connector
- Mounting base
- Fixed screw
- Microphone
- Micro SD card slot
- Reset
- It is recommended to install the water-proof connector for outdoor installations.
- DC 12V power supply is not required if a PoE switch or injector is used to power the camera.
Connecting Network Cable
- Loosen the nut from the main element.
- Run the network cable (without RJ 45 connector) through both elements. Then crimp the cable with RJ 45 connector.
- Connect the cable to the water-proof connector. Then tighten the nut and the main cover.
Installation
Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera.
- Attach the drill template of the camera to the place where you want to install the camera and then drill the screw hole and cable hole on the wall according to the drill template.
- Loosen the fixed screw to disassemble the camera. Then remove the cover from the camera unit to insert the SD card. After that, install the cover back to the camera unit and fix it firmly with the screws. (Note that the cover should not be installed unevenly.
- Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided.
- Install the camera unit and enclosure to the mounting base and then adjust if necessary to obtain an optimum view angle. Finally, fasten the camera with the fixed screw
Web Operation and Login
IP Scanner can search for the device on the local network.
Operation
- Make sure that the camera and the PC are connected to the same local network. The camera is set to DHCP by default.
- Install IP Scanner from the CD and run it after installation.
- In the device list, you can view the IP address, model number, and MAC address of each device. Select the applicable device and double click to open up the web viewer. You can also manually enter the IP address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and password is 1234. After logging in, follow directions to install applicable plugins.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>