i-therm AI-logger 96×96 Data Logger User Manual

June 10, 2024
i-therm

AI-logger 96×96 Data Logger

i-therm AI-logger 96x96 Data Logger User Manual-
product

OIM AI-logger V1.2

The OIM AI-logger V1.2 is a device used for logging analog input signals. It has a supply printer port, two alarm outputs, digital input, and PC connectivity.

Product Usage Instructions:

  • Connect the power supply to the supply printer port.
  • Connect the analog input device to the input terminals provided (PC+, PCDEV+, DEV-).
  • Connect the digital input device to the input terminalprovided.
  • Connect the PC to the logger using the PC connectivity port.
  • Turn on the logger.
  • Set the required parameters using the user interface provided.
  • The logger will start logging the analog input signals and can be monitored and controlled through the PC interface.

SPECIFlCATIONS

  1. Dl~PLAY TYPE:
    • 16X2 YELLOW LCD
  2. INPUT:
    • Available Units
    • : Refer table (Table NO.1)
    • RES0UJTION
    • : 0.1/0.01/0.001/1.
  3. RELAY OUTPUT
    • Contact Type
    • : N/0,CM,N/C
    • Contctet Ratins
    • : SA @ ZSOVAC or 30 voe
    • life Expectancy
    • : >S,00,000 operations
    • lsolation
    • : Inherent
  4. FUNCTI0N:
    • 0utputl/Output2
    • : Alarm outplrts
  5. POWER SUPPLY:
    • Supply Voltage Consumption
    • : 90-270VAC,50-60hz
  6. PHYSICAL:
    • Housing
    • : ABS plastic
  7. MEMORY CAPACITY
    • : Up to 2.SOlakh records
  8. 8.PRINTER CONNECTIVITY
    • : Available through RS-415 connector
  9. CAMMUNICATION
    • :M0DBUS protocol ls used

BACKPLATE

DIMENSIONS

i-therm AI-logger 96x96 Data Logger User Manual-
fig-2

INDEX

i-therm AI-logger 96x96 Data Logger User Manual-
fig-3

SETUP

FRONT PANEL KEYS
POWER ON SCREEN

RUN MODE SCREEN

i-therm AI-logger 96x96 Data Logger User Manual-
fig-6

SYSTEM CONFIGURATION

To Enter in Main Menu press SHIFT & SET key simultaneously for 3 seconds afer doing this following screen will appeari-therm AI-logger 96x96 Data Logger
User Manual-fig-7

COMMUNICATION SETTING (Flow Chart)

To Enter in this menu press SHIFT & SET key simultaneously after that enter appropriate password afer doing this following screen will appear. Screens with ‘<‘ indicates that change is allowable. If you just want to see all the settings(Don’t want to change) use .._ …,. to have a look. If you want to see/keep the previous value of the parameter then press shift key for 3 seconds so that ‘<‘ will get removed.i-therm AI-logger 96x96 Data Logger
User Manual-fig-8

COMMUNICATION SETTING(Descripton}

Basically used for the communication setting between devices & data logger and between data logger &PC simultaneuosly.
There are different parameters available which are as follow.i-therm AI-
logger 96x96 Data Logger User Manual-fig-9

RTC SETTING

(Real Time Clock setting)
It is used to set date & time in data logger. To Enter in this menu press SHIFT & SET key simultaneously after that enter appropriate password afer doing this, following screen will appear. Screens with ‘<‘ indicates that change is allowable. If you just want to see all the settings(Don’t want to change) use…,. ,., to have a look. If you want to see/keep the previous value of the parameter then press shift some time so that ‘<‘ will get removed.i-therm AI-logger 96x96 Data Logger User Manual-
fig-10

SCAN DEVICE FLOW CHART

To Enter in this menu press SHIFT & SET key simultaneously after that enter appropriate password afer doing this following screen will appear. Screens with ‘<‘ indicates that change is allowable. If you just want to see all the settings(Don’t want to change) use …_ .,,. to have a look. If you want to see/keep the previous value of the parameter then press shift some time so that ‘<‘ will get removed.i-therm AI-logger 96x96 Data Logger User Manual-
fig-11

(CONFIGURATION PROCESS WILL BE CARRIED OUT IN FOLLOWING MANNER FOR OTHER DEVICES. HERE WE ARE CONSIDERING DEVICE1)i-therm AI-logger 96x96 Data Logger
User Manual-fig-12

SCAN DEVICES(DESCRIPTION}

It is used to define number of devices which are connected to the data logger. The number of devices that can be connected maximum up to 4.i-therm AI-
logger 96x96 Data Logger User Manual-fig-13

Table No.1 (Available Units):i-therm AI-logger 96x96 Data Logger User
Manual-fig-14

DATA LOGGING(Flow Chart)

To Enter in this menu press SHIFT & SET key simultaneously after that enter appropriate password afer doing this following screen will appear. Screens with ‘<‘ indicates that change is allowable. If you just want to see all the settings(Don’t want to change) use • T to have a look. If you want to see/keep the previous value of the parameter then press shift some time so that ‘<‘ will get removed.

(NOTE: lf we select BATCH LOG MODE, SCREENS WILL APPEAR AS FOLLOW..).i-therm AI-logger 96x96 Data Logger User Manual-
fig-15

(NOTE: lf ONLY LOG MODE SCREENS WILL APPEAR AS FOLLOWS)

(NOTE: lf ONLY BATCH LOG MODE SCREENS WILL APP~AR AS FOLLOWS)

(NOTE: Following screens will appear depending on the type of start input)i-therm AI-logger 96x96 Data Logger User Manual-
fig-17i-therm AI-logger 96x96 Data Logger
User Manual-fig-18

DATA LOGGING(DESCRIPTION)

Basically it is used to keep the track of each devices connected. There are two ways in which we are going to keep the track that is Batch and Log. BATCH MODE : In batch we are going to provide the start and end of the batch so that data is going to get logged during that time span only after that no tracking. LOG MODE: In this we are going to log the data after specified duration of time given by us(user)i-therm AI-logger 96x96 Data
Logger User Manual-fig-19

PRINTER SETTING(Flow Chart)

To Enter in this menu press SHIFT & SET key simultaneously after that enter appropriate password afer doing this following screen will appear. Screens with ‘<‘ indicates that change is allowable. If you just want to see all the settings(Don’t want to change) use . T to have a look. If you want to see/keep the previous value of the parameter then press shift some time so that ‘<‘ will get removed.i-therm AI-logger 96x96 Data Logger User Manual-
fig-20

PRINTER SETTING(DESCRIPTION)

It will provide us options to make use of a printer during the process of data logging based on our convenience. Their are following optionsi-therm AI-
logger 96x96 Data Logger User Manual-fig-21

MEMORY STATUS(Flow Chart)

To Enter in this menu press SHIFT & SET key simultaneously after that enter appropriate password afer doing this following screen will appear. Screens with ‘<‘ indicates that change is allowable. If you just want to see all the settings(Don’t want to change) use • T to have a look. If you want to see/keep the previous value of the parameter then press shift some time so that ‘<‘ will get removed.i-therm AI-logger 96x96 Data Logger User Manual-
fig-22

MEMORY STATUS(DESCRIPTION}

It is used to do some memory settings. Options as followsi-therm AI-
logger 96x96 Data Logger User Manual-fig-23

CHANGE PASSWORD

IN THIS WE CAN CHANGE THE PASSWORD WHICH WE NEED TO ACCESS MAIN MENUi-therm
AI-logger 96x96 Data Logger User Manual-fig-24

TO ENTER IN THIS MENU PRESS PRINT KEY FOR 3SECONDS

(NOTE: FOR PRINT SUMMERY FOLLOWING SCREENS WILL OCCUR)i-therm AI-logger
96x96 Data Logger User Manual-fig-25

(NOTE: FOR SINGLE DATE OPTION, FOLLOWING SCREEN WILL APPEAR)

(NOTE: FOR DATE TO DATE DAY SELECTION, FOLLOWING SCREEN WILL OCCUR)i-therm AI-logger 96x96 Data Logger User Manual-
fig-26

Part A

(NOTE: IF WE SELECT ALL RECORDS, ONLY BATCH, ONLY LOG, ONLY ALARM, FOLLOWING SCREENS WILL APPEAR)

(NOTE: IF WE SELECT BETWEEN TIME, FOLLOWING SCREENS WILL APPEAR)

(NOTE: IF WE SELECT BATCH NUMBER FOLLOWING SCREENS WILL APPEAR)i-therm
AI-logger 96x96 Data Logger User Manual-fig-27

HOLD PRINT KEY FOR 3SECONDS YOU WILL COME ACROSS FOLLOWING OPTIONSi-therm
AI-logger 96x96 Data Logger User Manual-fig-28

Mfgd by: Innovative Instruments & Controls LLP

338, New Sonal Link Service Industrial Premises Co-op Society Ltd,
Building No.2,
Link Road,
Malad (W),
Mumbai – 400064.
Tel: 022-66939916/17/18;
E-mail : sales@itherm.co.in
Website : www.itherm.co.in

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals