hama 00086421 12W Charger with Micro USB Connection Instruction Manual

hama 00086421 12W Charger with Micro USB Connection

Product Information
The Hama product is a charger with a model identifier of 00086421. It has an input voltage of 100 – 240 V and an input AC frequency of 50/60 Hz. The output voltage is 5.0 V DC, with an output current of 2.4 A and a total output power of 12.0 W. The charger has an average efficiency of 79.9% and an efficiency of 75.5% at low load (10%). The power consumption at zero load is 0.08 W.

The charger is suitable for use worldwide, but a country-specific adapter may be required. Make sure to keep the device out of the reach of children and avoid splashing water to prevent the risk of electric shock.

• Please note that improper installation/mounting, improper use of the product, or failure to observe the operating instructions
  and/or safety notes may result in damage for which Hama GmbH & QQQQQQQQQQQQQCo KG assumes no liability and provides no warranty.

Product Usage

1. Before use, read the operating instructions and information completely.
2. Make sure the device is disconnected from the mains before cleaning or during prolonged periods of non-use.
3. The charger is suitable for mains voltages of 100 – 240 V and can be used worldwide. However, a country-specific adapter may be necessary.
4. Connect the device to the charger using a suitable cable.
5. Make sure the device is properly connected to the charger before plugging it into the mains.
6. Plug the charger into the mains.
7. The device will begin to charge once it is properly connected to the charger and plugged into the mains.

Follow the above steps to safely and properly use the Hama charger to charge your devices. Remember to keep the device out of the reach of children and avoid splashing water to prevent the risk
of electric shock. applied.

00086421/04.23

Thank you for choosing this Hama product!
Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference.

Explanation of warning symbols and notes

1. 1. Risk of electric shock  

   This symbol indicates a risk of electric shock from touching uninsulated product parts that may carry hazardous voltage.

2. Warning
   This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note
This symbol is used to indicate additional information or important notes

Package contents

• Charger
• These operating instructions

Safety instructions

• Protect the product from dirt, moisture and overheating and use it in dry rooms only.
• Do not drop the product and do not expose it to any major shocks.
• Do not operate the product outside the power limits specified in the technical data.
• Do not modify the device in any way. Doing so voids the warranty.
• Do not continue to operate the product if it is visibly damaged.
• Use the product only for the intended purpose.
• As with all electrical products, this device should be kept out of the reach of children.
•  Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
•  Route all cables so there is no risk of tripping.
•  Do not bend or crush the cable.
• Always pull directly on the plug when disconnecting the cable, never on the cable itself.
• Dispose of packaging material immediately in accordance with the locally applicable regulations.
• The product is intended only for use inside buildings.
•  Only use the article under moderate climatic conditions.
•  Do not use the product in areas in which electronic products are not permitted.
• Do not use the product in a damp environment and avoid splashing water.

Risk of electric shock

• Do not open the device or continue to operate it if it becomes damaged.
  

• Do not use the product if the

• AC adapter, the adapter cable or the mains cable are damaged.

• Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.

Operation

Note – mains voltage 100 – 240 V
The charger is suitable for mains voltages of 100 – 240 V and therefore can be used worldwide. Please note that a country-specific adapter may be necessary.

• Before connecting a device, check whether it can be adequately supplied with the charger’s current capacity.
• Ensure that the power of the connected device does not exceed 12 W.
• Note the instructions in your device’s operating manual.

Warning

• Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
• If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
• If you will not be using the product for a prolonged period, disconnect it from mains power.

Unless different instructions have been expressly given in the operating instructions for the devices you are charging, proceed as follows:

• Connect your device to the charger.
• Connect the charger to a properly installed and easily accessible mains socket.
• The charging process is displayed on your device.
•  Disconnect the device from the charger if you wish to interrupt the charging process or when the device is fully charged.
• Then disconnect the charger from the line connection.
  When charging the rechargeable batteries in the device, note the maximum charging times for the built-in batteries.

Care and maintenance

Only use soft, dry towels to clean the product.

Note
Disconnect the device from the mains before cleaning and during prolonged periods of non-use.

Technical data

Specifications according to Regulation (EU) 2019/1782

References

• hama.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>