MINN KOTA 1358894 Terrova Bow Mount Trolling Motor Owner’s Manual

June 10, 2024
MINN KOTA

1358894 Terrova Bow Mount Trolling Motor

Product Information

The Terrova is a bow-mount trolling motor made by Minn Kota Johnson
Outdoors Marine Electronics, Inc. It is designed to be used on
freshwater boats and has a composite shaft that comes with a
limited lifetime warranty. The motor has an 11-character serial
number that helps to identify the specific model and year of
manufacture. The motor can be registered online at
minnkotamotors.com/register, and it is recommended to keep the
receipt and serial number for future reference. The product also
comes with a limited two-year warranty.

Product Usage Instructions

1. Before using the Terrova trolling motor, thoroughly read the
user manual and follow all instructions and safety considerations.
2. Only use the motor on freshwater boats and ensure that minors
use the motor only under adult supervision. 3. When stowing or
deploying the motor, keep fingers clear of all hinge and pivot
points and all moving parts. 4. Use only Johnson Outdoors approved
accessories with the Minn Kota motor. Using non-approved
accessories may cause damage, unexpected motor operation, and
injury. 5. Keep all factory installed parts in place including
motor and accessory covers, enclosures, and guards. 6. The serial
number on the Terrova is located inside the mount below the motor
rests. Write down the serial number for future reference. 7. In
case of unexpected motor operation, remove power leads from the
battery immediately. 8. The Terrova trolling motor comes with a
lithium button battery. Keep batteries out of reach of children. If
you think batteries may have been swallowed or placed inside any
part of the body, seek immediate medical attention. 9. If you
encounter any issues with the product, contact Consumer Service and
provide them with the product’s serial number.

TERROVA
BOW-MOUNT TROLLING MOTOR
Owner’s Manual

INTRODUCTION

THANK YOU
Thank you for choosing Minn Kota. We believe that you should spend more time fishing and less time positioning your boat. That’s why we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought out and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the Minn Kota advantage that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are never done helping you catch more fish.

REGISTRATION

Remember to keep your receipt and immediately register your trolling motor. A registration card is included with your motor or you can complete registration on our website at minnkotamotors.com/register.
SERIAL NUMBER

Your Minn Kota 11-character serial number is very important. It helps to determine the specific model and year of manufacture. When contacting Consumer Service or registering your product, you will need to know your product’s serial number. We recommend that you write the serial number down so that you have it available for future reference.
NOTICE: The serial number on your Terrova is located inside the mount below the motor rests.

Made by Minn Kota Johnson Outdoors Marine Electronics, Inc. 121 Power Drive Mankato, MN 56001 USA Trolling Motors Produced in XXXX

PRODUCT DESCRIPTION MODEL XXXXXXX

XXV DC XX A

SER NO YYDDDC00000
EXAMPLE

MOTOR INFORMATION (For Consumer Reference Only)

Model:


Serial Number:


Purchase Date:


Store Where Purchased:


NOTICE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit. You may obtain service by: calling Minn Kota at 800-227-6433; returning your motor to the Minn Kota Factory Service Center; sending or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is available on our website at minnkotamotors.com. Please include proof of purchase, serial number and purchase date for warranty service with any of the above options.

2 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

TABLE OF CONTENTS
SAFETY CONSIDERATIONS …………………………………………………………………………………………… 4 WARRANTY ……………………………………………………………………………………………………………. 5 KNOW YOUR BOAT…………………………………………………………………………………………………….. 6 FEATURES……………………………………………………………………………………………………………… 7 INSTALLATION…………………………………………………………………………………………………………. 8
Installing the Terrova………………………………………………………………………………………….. 9 Identifying Trolling Motor Features by Their Associated Cables………………………………… 14 Routing Connection Cables ……………………………………………………………………………….. 14 Feature overview and connecting the cables ………………………………………………………… 16 BATTERY & WIRING INSTALLATION………………………………………………………………………………… 21 Boat Rigging & Product Installation …………………………………………………………………….. 21 Conductor Gauge and Circuit Breaker Sizing Table ………………………………………………… 21 Selecting the Correct Batteries…………………………………………………………………………… 22 Additional Considerations …………………………………………………………………………………. 22 Connecting the Batteries ………………………………………………………………………………….. 23 Connecting the Batteries in a Series ……………………………………………………………………. 24 MOTOR WIRING DIAGRAM ………………………………………………………………………………………….. 26 USING & ADJUSTING THE MOTOR …………………………………………………………………………………. 28 Mount Features ………………………………………………………………………………………………. 28 Stowing and Deploying the Motor……………………………………………………………………….. 29 Push-to-Test Battery Meter ……………………………………………………………………………….. 29 Adjusting the Depth of the Motor………………………………………………………………………… 30 Adjusting the Lower Unit for a Secure Stow ………………………………………………………….. 31 Installing an External Transducer ……………………………………………………………………….. 32 USING THE FOOT PEDAL ……………………………………………………………………………………………. 33 Controlling Speed & Steering with the Foot Pedal ………………………………………………….. 33 SERVICE & MAINTENANCE …………………………………………………………………………………………. 35 Propeller Replacement …………………………………………………………………………………….. 35 General Maintenance……………………………………………………………………………………….. 36 Troubleshooting………………………………………………………………………………………………. 36 For Further Troubleshooting and Repair ………………………………………………………………. 37 COMPLIANCE STATEMENTS………………………………………………………………………………………… 38 PARTS DIAGRAM & PARTS LIST ……………………………………………………………………………………. 40

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 3

SAFETY CONSIDERATIONS
Please thoroughly read the user manual. Follow all instructions and heed all safety and cautionary notices. Use of this motor is only permitted for persons that have read and understood these user instructions. Minors may use this motor only under adult supervision.
WARNING
You are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an accurate and reliable tool that will enhance boat operation and improve your ability to catch fish. This product does not relieve you from the responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a permanent watch so you can respond to situations as they develop. You must always be prepared to regain manual control of your boat. Learn to operate your Minn Kota product in an area free from hazards and obstacles.
WARNING
Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected from the power source when it is not in use or is off the water. When connecting the power-supply cables of the motor to the battery, ensure that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before using the motor make sure that the insulation of the power cables is not damaged. Disregarding these safety precautions may result in electric shorts of battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking the propeller. Avoid submerging the complete motor as water may enter the lower unit through control head and shaft. If the motor is used while water is present in the lower unit considerable damage to the motor can occur. This damage will not be covered by warranty.
WARNING
Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects. The motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming and for floating objects. Persons who lack the ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or other substances are not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise pressure level of the motor during use is less than 70dB(A). The overall vibration level does not exceed 2,5 m/sec2.
WARNING
When stowing or deploying the motor, keep fingers clear of all hinge and pivot points and all moving parts. In the event of unexpected operation, remove power leads from the battery.
WARNING
It is recommended to only use Johnson Outdoors approved accessories with your Minn Kota motor. Using non-approved accessories including to mount or control your motor may cause damage, unexpected motor operation and injury. Be sure to use the product and approved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected motor operation. Keep all factory installed parts in place including motor and accessory covers, enclosures and guards.
WARNING
THIS PRODUCT CONTAINS A BUTTON BATTERY. If swallowed, a lithium button battery can cause severe or fatal injuries within two hours. Keep batteries out of reach of children. If you think batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention.

4 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

WARRANTY

WARRANTY ON MINN KOTA FRESHWATER TROLLING MOTORS

Minn Kota Freshwater Trolling Motors – Limited Lifetime Warranty On Composite Shaft And Limited Two-Year Warranty On The Entire Product

Johnson Outdoors Marine Electronics, Inc. (“JOME”) extends the following limited warranty to the original retail purchaser only. Warranty coverage is not transferable.
Minn Kota Limited Two-Year Warranty on the Entire Product

JOME warrants to the original retail purchaser only that the purchaser’s new Minn Kota freshwater trolling motor will be materially free from defects in materials and workmanship appearing within two (2) years after the date of purchase. JOME will (at its option) either repair or replace, free of charge, any parts found by JOME to be defective during the term of this warranty. Such repair, or replacement shall be the sole and exclusive liability of JOME and the sole and exclusive remedy of the purchaser for breach of this warranty.
Minn Kota Limited Lifetime Warranty on the Composite Shaft

JOME warrants to the original retail purchaser only that the composite shaft of the purchaser’s Minn Kota trolling motor will be materially free from defects in materials and workmanship appearing within the original purchaser’s lifetime. JOME will provide a new composite shaft, free of charge, to replace any composite shaft found by JOME to be defective during the term of this warranty. Providing a new composite shaft shall be the sole and exclusive liability of JOME and the sole and exclusive remedy of the purchaser for breach of this warranty; and purchaser shall be responsible for installing, or for the cost of labor to install, any new composite shaft provided by JOME.
Exclusions and Limitations

This limited warranty does not apply to products that have been used in saltwater or brackish water, commercially or for rental purposes. This limited warranty does not cover normal wear and tear, blemishes that do not affect the operation of the product, or damage caused by accidents, abuse, alteration, modification, shipping damages, acts of God, negligence of the user or misuse, improper or insufficient care or maintenance. DAMAGE CAUSED BY THE USE OF OTHER REPLACEMENT PARTS NOT MEETING THE DESIGN SPECIFICATIONS OF THE ORIGINAL PARTS WILL NOT BE COVERED BY THIS LIMITED WARRANTY. The cost of normal maintenance or replacement parts which are not in breach of the limited warranty are the responsibility of the purchaser. Prior to using products, the purchaser shall determine the suitability of the products for the intended use and assumes all related risk and liability. Any assistance JOME provides to or procures for the purchaser outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver of the terms, limitations or exclusions, nor will such assistance extend or revive the warranty. JOME will not reimburse the purchaser for any expenses incurred by the purchaser in repairing, correcting or replacing any defective products or parts, except those incurred with JOME’s prior written permission. JOME’S AGGREGATE LIABILITY WITH RESPECT TO COVERED PRODUCTS IS LIMITED TO AN AMOUNT EQUAL TO THE PURCHASER’S ORIGINAL PURCHASE PRICE PAID FOR SUCH PRODUCT.
Minn Kota Service Information

To obtain warranty service in the U.S., the product believed to be defective, and proof of original purchase (including the date of purchase), must be presented to a Minn Kota Authorized Service Center. Go to www.minnkotamotors.com/support/service-providers/locate to find a Minn Kota Authorized Service Center. Any charges incurred for service calls, transportation or shipping/ freight to/from the Minn Kota Authorized Service Center, labor to haul out, remove, re-install or re-rig products removed for warranty service, or any other similar items are the sole and exclusive responsibility of the purchaser. Products purchased outside of the U.S. must be returned prepaid with proof of purchase (including the date of purchase and serial number) to any Authorized Minn Kota Service Center in the country of purchase. To contact Minn Kota Customer Service go to www.minnkotamotors.com/contact. Products repaired or replaced will be warranted for the remainder of the original warranty period, or for 90 days from the date of repair or replacement, whichever is longer. For any product that is returned for warranty service that JOME finds to be not covered by or not in breach of this limited warranty, there will be a billing for services rendered at the prevailing labor rate of the applicable Minn Kota Authorized Service Center and for a minimum of at least one hour.

Service Provider Locator

Contact Customer Service

NOTICE: Do not return your Minn Kota product to your retailer. Your retailer is not authorized to repair or replace products.

NOTICE: THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. IN NO EVENT SHALL ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND THE DURATION OF THE RELEVANT EXPRESS LIMITED WARRANTY. IN NO EVENT SHALL JOME BE LIABLE FOR PUNITIVE, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. Without limiting the foregoing, JOME assumes no responsibility for loss of use of product, loss of time, inconvenience or other damage.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations and/or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 5

KNOW YOUR BOAT
Bow

Port Gunwale

Starboard

Keel Port

Inboard Outboard

Starboard

Transom

Stern Bow
Hull 6 | minnkotamotors.com

Gunwale

Stern ©2022 Johnson Outdoors Marine Electronics, Inc.

FEATURES

Power Power Button

AutoPilot

Indicator Panel Stow Deploy Lever

Push-to-Test Battery Meter

Adjustable Depth Collar
Depth Collar Knob Lift Assist Housing
Steering Housing
Fall Away Ramps

Low Profile Foot Pedal

Lifetime Warranty Flexible Composite Shaft

Lift Assist Collar Propeller

Cool Quiet Power Motor

NOTICE: Specifications subject to change without notice. This diagram is for reference only and may differ from your actual motor.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 7

INSTALLATION

INSTALLING THE TERROVA
Your new Terrova comes with everything you’ll need to directly install it to the boat. This motor can be directly mounted to the boat or coupled with a Minn Kota quick release bracket for ease of mounting and removal. For installation with a quick release bracket, refer to the installation instructions provided with the bracket. For compatible quick release mounting brackets and to locate your nearest dealer, visit minnkotamotors.com. To install the motor directly to the boat, please follow the instructions provided in this manual. Please review the parts list, mounting considerations and tools needed for installation prior to getting started. For additional product support, please visit minnkotamotors.com.
INSTALLATION PARTS LIST

Item / Assembly

Part # Description

Qty.

AA

2994864 BAG ASSEMBLY – (BOLT, NUT, WASHERS)

1

1

2263462 BOLT-MOUNTING-1/4X2 W/STG

6

2

2261713 WASHER-1/4

6

3

2263103 NUT NYLOK 1/4-20 MTG

6

4

2301720 WASHER-MOUNTING RUBBER

6

5

MOTOR ASSEMBLY

1

6

2390800 t LANYARD, REMOTE W/ CARABEENER

1

7

2994075 t REMOTE ASY, IPILOT

1

p

2397106 t MANUAL, QUICK REF., IPILOT 1.6

1

8

2994076 Â REMOTE ASSEMBLY LINK TOUCHSCREEN

1

9

2373241 Â CABLE, USB REMOTE CHARGER LINK

1

10

2375901 Â ADAPTER, USB DC POWER LINK

1

11

2996400 t HEADING SENSOR ASSEMBLY SELECT MODELS ONLY

1

12

490389-1 Â CABLE, ETH (M12-M-M12-F, 30′

1

2211415 Ì CABLE-EXTENSION, PD/AP 110″ PRE-INSTALLED

1

13

490507-1 â CABLE, ADP-INT MDI 14 M12-120″ PRE-INSTALLED

1

2092600 PIN-DRIVE 1.06″ LG (SS)

1

14

2262658 PIN-DRIVE 1″ X 3/16″ S/S

1

2151726 WASHER-5/16 STD (S/S)

1

15

2091701 WASHER-PROP (LARGE)

1

2053101 NUT-PROP,NYLOC (MED) 5/16 SS

1

16

2093101 NUT-PROP,NYLOC,LG, 3/8 SS

1

2091160 PROP-WW2 (3-5/8″) REAMED

1

17

2341160 PROP-WW2 (4.5) W/ADP.RING

1

2331160 PROP-WW2 (4″) W/ADP.RING

1

BB

1378131 PROP IND 2091160 WDLS WDG II

1

CC

1378160 PROP KIT 2341160 112# WW2

1

DD

1378132 PROP IND 233160 WDLS WDG II

1

EE

2994722 FT PED ASY, TRV, W/SPOT LCK

1

FF

2994859 BAG, ASY-TERROVA/V2, RUB BUMPERS

1

18

2325110 PAD, FOOT PEDAL

5

p

2327132 INSTALLATION INSTRUCTIONS TERROVA

1

p

2397107 Â MANUAL, QUICK REF., IPILOT LINK 3.0

1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot. Â Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.

8 | minnkotamotors.com

7 12

8 11
13 10
9
6

18 FF
EE

5 4

AA

1

2

3

17

15 16 14

BB

CC DD

©2022 Johnson Outdoors Marine Electronics, Inc.

INSTALLING THE TERROVA

MOUNTING CONSIDERATIONS
It is recommended that the motor be mounted as close to the centerline of the boat as possible. Make sure the area under the mounting location is clear to drill holes and install nuts and washers. Make sure the motor rest is positioned far enough beyond the edge of the boat. The motor must not encounter any obstructions as it is lowered into the water or raised into the boat when stowed and deployed. Consider a quick release or adapter bracket with the installation of your motor. To view a list of accessories, please visit minnkotamotors.com.

TOOLS AND RESOURCES REQUIRED
· #3 Phillips Screw Driver · Drill · 9/32″ Drill Bit

· 7/16″ Box End Wrench · A second person to help with
the installation

View accessories available for your trolling motor at minnkotamotors.com.

INSTALLATION

INSTALLING THE TERROVA

1

a. Place the mount on an elevated, level surface such

1b

as a workbench or the tailgate of a pickup. The

motor, as removed from the box, should be in the

stowed position.

b. Remove the four sideplate screws using a #3 Phillips screwdriver. Two of these screws will be located on each side of the mount.

NOTICE: This motor weighs approximately 65lbs. We recommend having a second person help with the installation.

Sideplate Screw

Deployed

Stowed

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 9

INSTALLING THE TERROVA

2

c. Remove the Right Sideplate.

2d

d. Swing the Left Sideplate out and away from the Base Extrusion.

2c

Base Extrusion Left Sideplate

Right Sideplate

3

e. Make sure that the Power Cables from the battery

are disconnected, or that the breaker,

if equipped, is “off.”

WARNING

Make sure the motor is mounted on a level surface and is not connected to a power source.

4

f. Place the mount as close to the centerline or keel

of the boat as possible. The motor can be installed

on either the Port or Starboard side of the boat

based on personal preference. Check placement

with the motor in the stowed and deployed positions.

Review the mounting considerations at the

beginning of the installation.

Power Cables

Keel

Deck of Boat

10 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

5 ITEM(S) NEEDED #4 x 6
g. When the motor is in the deployed position, make sure that the Shaft is 1-1/2″ out past the Gunwale of the boat. The lower unit, when stowed and deployed must not encounter any obstructions.
h. Check to be sure that the mount is level. Use the Rubber Washers (Item #4) provided to create a level surface if necessary.

6

i. It is recommended to mark at least 4 of the 6 holes

in the Base Extrusion and to have a minimum of

two bolts on each side that are located the farthest

apart. Ideal installation would allow for 6 bolts to be

used, with a minimum of 4.

j. Drill through the deck of the boat using a 9/32″ Drill Bit on the marked locations.

INSTALLING THE TERROVA

Gunwale

1-1/2″ Minimum

Shaft

Drilling Locations

Base Extrusion

Drilling Locations

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 11

INSTALLING THE TERROVA

7 ITEM(S) NEEDED

2 x 6

1 x 6

3 x 6

k. Put a 1/4-20 x 2″ (Item #1) screw in each of the drilled locations. The screw should pass through the Base Extrusion and the boat deck. If the rubber washers (Item #4) are used, they should sit between the Base Extrusion and boat deck. Make sure to secure the motor with screws on each side of the Base Extrusion.
l. Place a Flat Washer (Item #2) and then a Nylock Nut (Item #3) at the end of each screw as shown and secure. Make sure all hardware is secure.
NOTICE: To prevent seizing of the stainless steel hardware, do not use high speed installation tools. Wetting the screws or applying an anti-seize may help prevent seizing.

4 x 6

Screw

Rubber Washer Nylock Nut

Flat Washer

8

m. Replace the Right Sideplate.

8n

n. Swing the Left Sideplate back into its correct position on the Base Extrusion.

8m

Boat Deck

Base Extrusion Left Sideplate

12 | minnkotamotors.com

Right Sideplate

©2022 Johnson Outdoors Marine Electronics, Inc.

9

o. Replace the four sideplate screws using a #3 or #2

Phillips screwdriver. Two of these screws will be

located on each side of the mount.

INSTALLING THE TERROVA

10 ITEM(S) NEEDED #18 x 5

EE x 1

p. Take the Foot Pedal (Item #EE) and turn it over. Put a Foot Pedal Pad (Item

18) in each of the pad locations.

NOTICE: The pads are recommended when using the Foot Pedal on non-carpeted surfaces.

Sideplate Screw
Foot Pedal Bottom Foot Pedal Pad Placement

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 13

IDENTIFYING TROLLING MOTOR FEATURES BY THEIR ASSOCIATED CABLES

IDENTIFYING TROLLING MOTOR FEATURES BY THEIR ASSOCIATED CABLES

Your trolling motor may be pre-installed with Built-In MEGA Down Imaging OR Universal Sonar, and may include i-Pilot Link. All of these features require cables to be connected to an output device. These connections are present on the trolling motor and have cables that exit below the Control Head. To better identify cables present, refer to the diagrams below that detail what the Built-In MEGA Down Imaging, Universal Sonar and i-Pilot Link cable connectors look like.

Built-In MEGA Down Imaging

Universal Sonar

i-Pilot Link

Fourteen Pin Connector Locking Collar

Four Pin Connector

Eight Pin Connector

Built-In MEGA Down Imaging from
Control Head

Universal Sonar Cable from Control Head

Locking Collar i-Pilot Link Ethernet Cable
from Control Head

If one connection below the Control Head is present, the motor may be equipped with:

1. i-Pilot and Universal Sonar, 2. i-Pilot and Built-in MEGA Down Imaging, 3. ONLY Universal Sonar, or 4. ONLY Built-in MEGA Down Imaging.

NOTICE: The i-Pilot system does not have an external wired connection.

If two connections below the Control Head are present, the motor may be equipped with either:

1. i-Pilot Link and Universal Sonar or 2. i-Pilot Link and Built-in MEGA Down Imaging

One Connection

Built-in MEGA Down Imaging or Universal Sonar

Control Head

Two Connections

i-Pilot Link Built-in MEGA Down Imaging or Universal Sonar

Control Head

Coil Cord

Coil Cord

ROUTING CONNECTION CABLES
Please follow these instructions for routing any and all of the cables present for any of the pre-installed features that may come with your trolling motor. This routing should be followed whether there are one or two connection cables present. If you are unsure of the cables present, please review the “Identifying Trolling Motor Features By Their Associated Cables” section of these Installation Instructions.

14 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

ROUTING CONNECTION CABLES

1

a. Place the motor in the deployed position.

b. Locate the Built-in MEGA Down Imaging, i-Pilot Link and/or Universal Sonar cable(s), at the base of the Control Head.

CAUTION

Not following the recommended wire routing for the Built-in MEGA Down Imaging, i-Pilot Link and/or Universal Sonar cable(s), if equipped, may cause damage to the product and void your product warranty. Route cables away from pinch points or other areas that may cause them to bend in sharp angles. Routing the cables in any way other than directed may cause damage to the cables by being pinched or severed.

NOTICE: Universal Sonar connector shown for illustration purposes.

One Connection

Built-in MEGA Down Imaging or Universal Sonar

Coil Cord

Two Connections

i-Pilot Link Built-in MEGA Down Imaging or Universal Sonar

Universal Sonar Connector

Control Head Control Head Coil Cord

2

c. The cable(s) should be fed all the way through

the Coil Cord. It/they should exit the Coil Cord at

the bottom of the Coil Cord, where it connects to

the Mount.

Two Connections

i-Pilot Link

Control Head

Built-in MEGA Down Imaging or Universal Sonar

Coil Cord

Mount

One Connection

Built-in MEGA Down Imaging or Universal Sonar

Coil Cord

Control Head

Mount

NOTICE: After the cable(s) exit(s) the Coil Cord, it/they should be routed through an established routing system on the boat, in an area with minimal interference. Power cables or other elements that may produce interference for the sonar signals. Inspect the selected route carefully to ensure that there are no sharp edges, obstacles, or obstructions that may damage the cables.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 15

FEATURE OVERVIEW AND CONNECTING THE CABLES

FEATURE OVERVIEW AND CONNECTING THE CABLES
The cable(s) from the Control Head for each feature installed on the trolling motor is connected to an output device separately. Once the features that may be installed are identified, follow the instructions below to ensure the cables are connected correctly.
Built-In MEGA Down Imaging
Built-In MEGA Down Imaging delivers nearly 3X the output of standard Side Imaging®, and takes fishfinding into the megahertz frequency for the very first time. The Minn Kota flagship families of trolling motors, including Ultrex, Ulterra, Terrova, and Fortrex, now include Built-In MEGA Down Imaging sonar, the clearest imaging available only from Humminbird. With Humminbird MEGA imaging sonar built right into the trolling motor, you now have a crystal clear view of what’s directly beneath the boat, without having to manage all of the cables that come with external transducers. The Built-In MEGA DI transducer is only available on new models equipped from the factory and cannot be added to an existing trolling motor.
The Built-in MEGA DI transducer will provide both MEGA Down Imaging and 2D CHIRP Digital Sonar to select Humminbird models. All Built-In MEGA DI trolling motors, will come “Apex and Solix Ready” out of the box. An adapter cable accessory (MKR-MDI-1 1852085 or MKR-MDI-2 1852086) is available for purchase that will allow the connection of any compatible Humminbird Helix fish finder. The MKR-MDI-1 is used on Helix 8, 9, 10, 12 and 15 models. The MKR-MDI-2 is used for Humminbird Helix 7 models only. See the Built-In MEGA Down Imaging Compatibility chart online.
NOTICE: You can only view Down Imaging with a MEGA DI or MEGA SI HELIX G2N, G3N or G4N Series model and a required adapter, or with any SOLIX or APEX Series model. The built-in transducer cannot supply MEGA Imaging to Humminbird models that do not already have the capability. If you have a G2/G2N, G3/G3N HELIX that is not a MEGA SI or MEGA DI model, you will still get 2D Dual Spectrum CHIRP Sonar from the transducer. SOLIX G1 and HELIX G2 and G2N units need to be running the latest software update to view sonar from motors with Built-In MEGA Imaging. You can get the latest version of software for your fish finder on humminbird.com. Built-In MEGA Imaging is not supported by HELIX G1 models or other brands of fish finders.

1

a. Place the motor in the deployed position.

b. The Built-In MEGA Down Imaging connector from the Control Head is a 14 pin connector. Built-In MEGA Down Imaging may be installed on its own, or in conjunction with an i-Pilot or i-Pilot Link system. It will never be installed with Universal Sonar. Locate and identify the correct connection for Built-in MEGA Down Imaging cable(s), at the base of the Control Head.

NOTICE: Built-in MEGA Down Imaging is always paired with either i-Pilot or i-Pilot Link on Terrova, Ulterra and Ultrex motors. It may be pre-installed on a Fortrex motor without other features that require external connections.

i-Pilot Link

Control Head

Built-in MEGA Down Imaging

Coil Cord

Fourteen Pin Connector
Built-in MEGA Down Imaging cable from
Control Head

Mount
NOTICE: Critical cable routing for 60″ and 72″ motors with i-Pilot Link and Built-in MEGA Down Imaging. Accessory Cables must exit the Coil Cord leaving three or more open coils between where the cables exit and the motor base; as assembled by the factory. Routing the cables in any other manner will not allow the motor to stow properly.

16 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

BUILT-IN MEGA DOWN IMAGING

2

c. When installing with a Solix or Apex, the Built-In MEGA Humminbird Solix or Apex Fish Finder

Down Imaging cable can be plugged directly into the

Solix/Apex fish finder. Plug the Built-in MEGA Down

Imaging cable into the corresponding connection on

the Solix/Apex fish finder.

d. When installing with a Helix, first attach the Adapter Cable and then plug the Adapter Cable into the Helix fish finder. The Adapter Cable will only have one connection that is keyed on the back of the Helix fish finder. Plug the Adapter Cable into the only matching keyed connection.

Fourteen Pin Connector Locking Collar

Solix/Apex Fish Finder Connection Plug directly into Solix/ Apex Fish Finder

NOTICE: Check for compatibility or any required adapter cables online at minnkotamotors.com. The cable from the trolling motor can be extended with a 10′ Extension Cable #720081-1 or the 30′ Extension Cable #720081-2 found at humminbird.com.

Built-In MEGA Down Imaging from Trolling Motor
Humminbird Helix Fish Finder

NOTICE: If any cables need to be routed, please follow the guidelines in the Routing Connection Cables section of these installation instructions.

Fourteen Pin Connector Adapter Cable (Helix ONLY)
Locking Collar

Adapter Cable Keyed Connection

Keyed Adapter Cable for Helix Fish Finder
NOTICE: The connectors are keyed to prevent reversed installation.

Built-In MEGA Down Imaging from
Trolling Motor

Plug into Helix Fish
Finder

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 17

UNIVERSAL SONAR

Universal Sonar
Your trolling motor may be pre-installed with a Universal Sonar transducer system. Universal Sonar is a 2D sonar transducer with a temperature sensor that is integrated into the lower unit of the trolling motor. It has an operating frequency of 83/200 kHz. Connecting this transducer to a compatible fish finder gives you a 2D sonar view of what is happening directly below your trolling motor. The integrated design protects the transducer from underwater hazards, and prevents tangles and damage to the transducer cables.
All Universal Sonar motors are equipped with an internal bonding wire, incorrect rigging will cause sonar interference and can damage your trolling motor, electronics and other boat accessories. To minimize trolling motor interference, ensure that the fish finder and trolling motor are powered by separate batteries. Please refer to the Battery & Wiring Installation and Motor Wiring Diagram sections of this manual for correct rigging instructions.
The Universal Sonar Cables are shielded to minimize interference. To protect this shielding the cables should not be pulled tight against sharp angles or hard objects. If using cable ties, do not over-tighten. Any excess cable should be bundled in a loose loop of no less than 4″ in diameter. In certain situations, air bubbles may adhere to the surface of the Universal Sonar transducer, and effect the performance. If this happens simply wipe the surface of the transducer with your finger.

NOTICE: Universal Sonar does not support imaging screens that require higher frequencies such as 455 kHz or 800 kHz (Down Imaging, Side Imaging, etc.). Down Imaging (DI) specific units are not compatible with Universal Sonar. See compatibility chart for a list of compatible fish finders at minnkotamotors.com.

The connector for Universal Sonar exits the trolling motor below the Control Head and consists of a 4-pin plug. An adapter cable (MKR-US2) that is sold separately is required for all installations. For a current list of compatible fish finders and the correct adapter cable, or more information on Universal Sonar, please visit minnkotamotors.com.

1

a. Place the motor in the deployed position.

b. Locate the Universal Sonar, if equipped, at the base of the Mount.

c. Locate the Universal Sonar four pin connector at the end of Universal Sonar Extension Cable. The connector is black with a stainless steel threaded locking collar.

Control Head Universal
Sonar Coil Cord

NOTICE: Your fish finder should be turned off until this procedure is complete.

Four Pin Connector 18 | minnkotamotors.com

Universal Sonar Cable from Control Head

Mount
NOTICE: If the cable length does not reach the desired fish finder installation location, a 14.5′ extension cable is available (MKR-US2-11) (sold separately).

©2022 Johnson Outdoors Marine Electronics, Inc.

i-PILOT LINK

2

NOTICE: The Universal Sonar Cable may not be

2d

long enough to reach the fish finder. If the cable

length does not reach the desired fish finder

installation location, a 14.5′ extension cable is available to purchase. Minn Kota recommends

Four Pin Connector

using the MKR-US2-11.

d. Take the Universal Sonar Extension Cable, if needed, and attach it to the Universal Sonar Cable exiting the Control Head. Firmly push the plug together and twist the locking collar until it is snug.

Universal Sonar Cable from Control Head

Locking Collar

Universal Sonar Extension Cable

e. Install the Universal Sonar Cable that exits the Control Head or the Universal Sonar Extension Cable (if used) to the appropriate Universal Sonar Adapter Cable. Install the Adapter Cable to your fish finder. Refer to your fish finder manual for complete installation instructions.

NOTICE: The connectors are keyed to prevent reversed installation.
2e

NOTICE: If any cables need to be routed, please follow the guidelines in the Routing Connection Cables section of these installation instructions.

Locking Collar Universal Sonar Cable from Control Head OR Universal Sonar
Extension Cable

Universal Sonar Adapter Cable to
fish finder

i-Pilot Link

i-Pilot Link allows your Minn Kota trolling motor and Humminbird to communicate with each other to change the way you fish. i-Pilot Link delivers a large array of GPS capabilities including controlling speed, steering, Spot- Lock, and the ability to record and retrace paths on the water, all at your fingertips. To learn more about the GPS capabilities available with your i-Pilot Link navigation system, please refer to the Owner’s Manual by visiting minnkotamotors.com.

The i-Pilot Link remote and controller make up the i-Pilot Link navigation system. The i-Pilot Link remote comes paired to the controller from the factory. The i-Pilot Link controller contains a very sensitive compass and is where all GPS satellite and i-Pilot

NOTICE: The i-Pilot Link system needs an external wired connection. The i-Pilot system does not need an external wired connection.

Link remote signals are received. The i-Pilot Link controller is

contained in the trolling motor Control Head and is connected to a fish finder from a connection cable that exits the Control Head.

The Ethernet cable for the i-Pilot Link system has an 8-pin connector. The i-Pilot Link system can be connected directly to the Humminbird or to the Humminbird Ethernet Switch (optional). If you purchase an Ethernet Switch, install it using the instructions included in the Ethernet Installation Guide. The Ethernet Extension Cable is optional for your installation. To purchase Ethernet switches, Ethernet cables, and extension cables, visit the website humminbird.com or call Humminbird Customer Service at 1-800-633-1468. Depending on the shape of the Ethernet port on your Humminbird fish finder, an additional ethernet adapter cable (Ethernet Adapter Cable AS EC QDE #720074-1 for Helix fish finders) may be required for the installation. Refer to your fish finder operations manual or see the i-Pilot Link Compatibility Chart on our website for a list of all compatible Humminbird Units and SC Cards.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 19

i-PILOT LINK

1

a. Place the motor in the deployed position.

b. The i-Pilot Link connector from the Control Head is an 8-pin connector. Locate and identify the correct connection for i-Pilot Link, at the base of the Control Head.

NOTICE: i-Pilot Link will be paired with either Built-in MEGA Down Imaging or Universal Sonar on Ultrex, Ulterra or Terrova. i-Pilot Link is not a feature offered on Fortrex motors.

i-Pilot Link

Control Head

Built-in MEGA Down Imaging or Universal Sonar

Coil Cord

NOTICE: Paired with a Universal Sonar connector for illustration purposes. A Built-in MEGA Down Imaging connector may be present instead.

Mount

NOTICE: Critical cable routing for 60″ and 72″ motors with i-Pilot Link and Built-in MEGA Down Imaging. Accessory Cables must exit the Coil Cord leaving three or more open coils between where the cables exit and the motor base; as assembled by the factory. Routing the cables in any other manner will not allow the motor to stow properly.

2 ITEM(S) NEEDED

12 x 1

c. If necessary, to reach the installed fish finder, take the i-Pilot Link Ethernet Cable (Item #12) and attach it to the i-Pilot Link cable exiting the Control Head.
NOTICE: If any cables need to be routed, please follow the guidelines in the Routing Connection Cables section of these installation instructions.
d. Install the i-Pilot Link Ethernet Cable directly into the Humminbird fish finder, or refer to your fish finder installation manual for complete installation instructions. If an Adapter Cable is needed (Ethernet Adapter Cable AS EC QDE for Helix fish finders), install it on the end of the i-Pilot Link Ethernet Cable and refer to your fish finder installation manual for complete installation instructions.

Eight-Pin Connector

Locking Collar i-Pilot Link Ethernet

i-Pilot Link Ethernet Cable from Control Head

Extension Cable OR Ethernet Extension Cable

NOTICE: The connectors are keyed to prevent reversed installation.

20 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

BATTERY & WIRING INSTALLATION

BOAT RIGGING & PRODUCT INSTALLATION
For safety and compliance reasons, we recommend that you follow American Boat and Yacht Council (ABYC) standards when rigging your boat. Altering boat wiring should be completed by a qualified marine technician. The following specifications are for general guidelines only:
CAUTION
These guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional electrical devices from the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are using wire longer than that provided with your unit, follow the conductor gauge and circuit breaker sizing table below. If your wire extension length is more than 25 feet, we recommend that you contact a qualified marine technician.

CAUTION

An over-current protection device (circuit breaker or fuse) must be used. Coast Guard requirements dictate that each ungrounded current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse. The type (voltage and current rating) of the fuse or circuit breaker must be sized accordingly to the trolling motor used. The table below gives recommended guidelines for circuit breaker sizing.

CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE
This conductor and circuit breaker sizing table is only valid for the following assumptions:

1. No more than 2 conductors are bundled together inside of a sheath or conduit outside of engine spaces. 2. Each conductor has 105° C temp rated insulation. 3. No more than 5% voltage drop allowed at full motor power based on published product power requirements.

Motor Thrust / Model
30 lb. 40 lb., 45 lb. 50 lb., 55 lb.
70 lb. 80 lb. 101 lb. Engine Mount 101 112 lb. Engine Mount 160 E-Drive

Max Amp Draw
30 42 50 42 56 46 50 52 116 40

Circuit Breaker
50 Amp @ 12 VDC
60 Amp @ 12 VDC 50 Amp @ 24 VDC 60 Amp @ 24 VDC 50 Amp @ 36 VDC 60 Amp @ 36 VDC 60 Amp @ 36 VDC (2) x 60 Amp @ 24 VDC 50 Amp @ 48 VDC

5 feet 10 AWG 10 AWG 8 AWG 10 AWG 8 AWG 8 AWG 8 AWG 8 AWG 6 AWG 10 AWG

10 feet 10 AWG 8 AWG 6 AWG 10 AWG 8 AWG 8 AWG 8 AWG 8 AWG 6 AWG 10 AWG

Wire Extension Length
15 feet 8 AWG 6 AWG 4 AWG 8 AWG 8 AWG 8 AWG 8 AWG 8 AWG 4 AWG 10 AWG

20 feet 6 AWG 4 AWG 4 AWG 8 AWG 6 AWG 8 AWG 8 AWG 8 AWG 2 AWG 10 AWG

25 feet 4 AWG 4 AWG 2 AWG 6 AWG 6 AWG 8 AWG 8 AWG 8 AWG 2 AWG 10 AWG

NOTICE: Wire Extension Length refers to the distance from the batteries to the trolling motor leads. Consult website for available thrust options. Maximum Amp Draw values only occur intermittently during select conditions and should not be used as continuous amp load ratings.

Reference United States Code of Federal Regulations: 33 CFR 183 ­ Boats and Associated Equipment ABYC E-11: AC and DC Electrical Systems on Boats

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 21

SELECTING THE CORRECT BATTERIES
SELECTING THE CORRECT BATTERIES
The motor will operate with any lead acid, deep cycle marine 12-volt battery/batteries. For best results, use a deep cycle, marine battery with at least a 105 amp-hour rating. Maintain battery at full charge. Proper care will ensure having battery power when you need it, and will significantly improve the battery life. Failure to recharge lead-acid batteries (within 12-24 hours) is the leading cause of premature battery failure. Use a multi-stage charger to avoid overcharging. We offer a wide selection of chargers to fit your charging needs. If you are using a crank battery to start a gasoline outboard, we recommend that you use a separate deep cycle marine battery/batteries for your Minn Kota trolling motor. For more information on battery selection and rigging, please visit minnkotamotors.com. Minn Kota trolling motors can run on Lithium-Ion batteries. However, they are specifically designed to run on traditional lead-acid batteries (flooded, AGM or GEL). Lithium-Ion batteries maintain higher voltages for longer periods of time than lead acid. Therefore, running a Minn Kota trolling motor at speeds higher than 85% for a prolonged period could cause permanent damage to the motor.
WARNING
Never connect the (+) and the (­) terminals of the same battery together. Take care that no metal object can fall onto the battery and short the terminals. This would immediately lead to a short and extreme fire danger.
CAUTION
Refer to “Conductor Gauge and Circuit Breaker Sizing Table” in the previous section to find the appropriate circuit breaker or fuse for your motor. For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended.
CAUTION
Please read the following information before connecting your motor to your batteries in order to avoid damaging your motor and/or voiding your warranty.
ADDITIONAL CONSIDERATIONS
Using Alternator Chargers
Your Minn Kota trolling motor may be designed with an internal bonding wire to reduce sonar interference. Most alternator charging systems do not account for this bonding wire, and connect the negative posts of the trolling motor batteries to the negative posts of the crank/ starting battery. These external connections can damage connected electronics and the electrical system of your trolling motor, voiding your warranty. Review your charger’s manual carefully or consult the manufacturer prior to use to ensure your charger is compatible.
Minn Kota recommends using Minn Kota brand chargers to recharge the batteries connected to your Minn Kota trolling motor, as they have been engineered to work with motors that include a bonding wire.

22 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

CONNECTING THE BATTERIES
Additional Accessories Connected to Trolling Motor Batteries
Significant damage to your Minn Kota motor, your boat electronics, and your boat can occur if incorrect connections are made between your trolling motor batteries and other battery systems. Minn Kota recommends using an exclusive battery system for your trolling motor. Where possible, accessories should be connected to a separate battery system. Radios and sonar units should not be connected to any trolling motor battery systems as interference from the trolling motor is unavoidable. If connecting any additional accessories to any trolling motor battery system, or making connections between the trolling motor batteries and other battery systems on the boat, be sure to carefully observe the information below.
The negative (-) connection must be connected to the negative terminal of the same battery that the trolling motor negative lead connects to. In the diagrams below this battery is labeled “Low Side” Battery. Connecting to any other trolling motor battery will input positive voltage into the “ground” of that accessory, which can cause excess corrosion. Any damage caused by incorrect connections between battery systems will not be covered under warranty.
Automatic Jump Start Systems and Selector Switches
Automatic jump start systems and selector switches tie the negatives of the connected batteries together. Connecting these systems to the “High Side” Battery or “Middle” Battery in the diagrams below and will cause significant damage to your trolling motor and electronics. The only trolling motor battery that is safe to connect to one of these systems is the “Low Side” Battery.
NOTICE: The internal bonding wire is equipped with a 3 amp fuse. Improper connections described above carrying in excess of 3 amps will blow this fuse and no further damage will be exhibited. If this occurs, RF interference from the trolling motor affecting sonar units and other electronics will be more significant. If the fuse is blown the wiring error should be found and addressed prior to replacing the fuse. The replacement fuse should be 3 amps or less. An intact fuse does not imply correct rigging; significant damage can be done by incorrect wiring without approaching 3 amps of current.
CONNECTING THE BATTERIES
12-Volt Systems
1. Make sure that the motor is switched off (speed selector on “OFF” or “0”). 2. Connect positive ( + ) red lead to positive ( + ) battery terminal. 3. Connect negative ( ­ ) black lead to negative ( ­ ) battery terminal.
WARNING
For safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity and follow instructions in your boat owner’s manual.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 23

CONNECTING THE BATTERIES IN SERIES

CONNECTING THE BATTERIES IN SERIES (IF REQUIRED FOR YOUR MOTOR)
24-Volt Systems
Two 12-volt batteries are required. The batteries must be wired in series, only as directed in the wiring diagram, to provide 24 volts.
1. Make sure that the motor is switched off (speed selector on “0”).
2. Connect a connector cable to the positive ( + ) terminal of battery 1 and to the negative ( ­ ) terminal of battery 2.
3. Connect positive ( + ) red motor lead to positive ( + ) terminal on battery 2.
4. Connect negative ( ­ ) black motor lead to negative ( ­ ) terminal of battery 1.

To trolling motor negative

+24 Volts to trolling motor positive (or circuit breaker)

24 Volt Series Connection

Neg – Pos +

Neg – Pos +

Battery #1 (Low Side)

Battery #2 (High Side)

Two 12-volt batteries connected in series for 24 volts

WARNING
For safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity and follow instructions in your boat owner’s manual.

WARNING
· For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteries are being charged.
· Improper wiring of 24/36 volt systems could cause battery explosion.
· Keep leadwire wing nut connections tight and solid to battery terminals.
· Locate battery in a ventilated compartment.

24 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

CONNECTING THE BATTERIES IN SERIES

36-Volt Systems

Three 12-volt batteries are required. The batteries must be wired in series, only as directed in the wiring diagram, to provide 36 volts.

1. Make sure that the motor is switched off (speed selector on “0”).
2. Connect a connector cable to the positive ( + ) terminal of battery 1 and to the negative ( ­ ) terminal of battery 2 and another connector cable from the positive ( + ) terminal of battery 2 to the negative ( ­ ) terminal of battery of battery 3.

To trolling motor negative 24 Volt Series Connection

Neg – Pos +

Neg –

+36 Volts to trolling motor positive (or circuit breaker)
36 Volt Series Connection

Pos +

Neg – Pos +

3. Connect positive ( + ) red motor lead to positive ( + ) terminal on battery 3.
4. Connect negative ( ­ ) black motor lead to negative ( ­ ) terminal of battery 1.

Battery #1 (Low Side)

Battery #2 (Middle)

Battery #3 (High Side)

Three 12-volt batteries connected in series for 36 volts

WARNING

For safety reasons, do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity and follow instructions in your boat owner’s manual.

WARNING
· For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteries are being charged.
· Improper wiring of 24/36 volt systems could cause battery explosion.
· Keep leadwire wing nut connections tight and solid to battery terminals.
· Locate battery in a ventilated compartment.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 25

MOTOR WIRING DIAGRAM

TERROVA

The following Motor Wiring Diagram applies to all Terrova models that do not come factory installed i-Pilot or i-Pilot Link. Not all models

come with Universal Sonar or Built-in MEGA Down Imaging. CoPilot can be installed on these models, but this feature may not come

already installed from the factory.

CoPilot

CoPilot Control Board

Brown Fuse Black M-

Ground

Black M-

Black B-

Brown

Red M+

Control Head

Power Switch

Red B+

Black

Universal Sonar
or Built-in MEGA Down
Imaging
Steering Housing

Coil Cord

Red Black

Red M+ White

Brown White

Red M+

Black M-

Brown
Accessory Attachment
Red

Foot Pedal Attachment Black

Black
Accessory Attachment
Black B- 12v Red B+

Black

Battery Gauge

AutoPilot (Red) Spot-Lock (Blue)

Foot Pedal
Foot Pedal Attachment

Battery 1

24v

Red B+

Constant (Green)
Foot Pedal Control Board

Spot-Lock Sensor
Speed Adjustment Sensor

Black B-

Battery 1

Battery 2

36v

Red B+

Motor

Battery 1

Battery 2

Battery 3

NOTICE: This is a multi-voltage diagram. Double-check your motor’s voltage for proper connections. Over-Current Protection Devices are not shown in this illustration. If equipped with Universal Sonar or Built-in MEGA Down Imaging, please visit the website minnkotamotors.com for additional information.

26 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

MOTOR WIRING DIAGRAM

TERROVA WITH i-PILOT OR i-PILOT LINK
The following Motor Wiring Diagram applies to all Terrova models that come factory installed with either i-Pilot or i-Pilot Link.

i-Pilot

Accessory Attachment

Brown Fuse

Black M-

Ground

Brown

Red M+

Control Head

Power Switch

Black MRed B+

Black BBlack

Coil Cord i-Pilot Link
Cable
Universal Sonar

or Built-in MEGA Down
Imaging

Brown

White

Red

Black MRed M+

Accessory Attachment

Brown Red

Black

Red M+

White Black

Accessory Attachment

Foot Pedal Attachment

Black B- 12v

Black

Red B+

Steering Housing

Black

Battery Gauge

AutoPilot (Red) Spot-Lock (Blue)

Foot Pedal
Foot Pedal Attachment

Constant (Green)

Spot-Lock Sensor

Foot Pedal Control Board

Speed Adjustment Sensor

Battery 1

24v

Red B+

Black B-

Battery 1

Battery 2

36v

Red B+

Motor

Battery 1

Battery 2

Battery 3

NOTICE: This is a multi-voltage diagram. Double-check your motor’s voltage for proper connections. Over-Current Protection Devices are not shown in this illustration. If equipped with Universal Sonar or Built-in MEGA Down Imaging, please visit the website minnkotamotors.com for additional information.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 27

USING & ADJUSTING THE MOTOR

MOUNT FEATURES
Become familiar with the features of the motor to maximize the capabilities this product offers.

Depth Collar Knob

Steering Housing

Depth Collar

Lift Assist Housing

Lift Assist Collar

Shaft

Lower Unit

Fall Away Ramp

Stow Deploy Lever

Power Power Button Indicator Panel

AutoPilot

Push-to-Test Battery Meter

Depth Collar & Depth Collar Knob
The Depth Collar is located on the Shaft above the Lift Assist Housing. It functions to hold the motor at the proper depth while deployed. It also functions to hold the Lower Unit in place when stowed while not in use and during transport. The Depth Collar Knob is used to loosen and tighten the Depth Collar so that it can be used to slide up and down the motor shaft.
WARNING
When the motor is being transported, it is important to place the Depth Collar snug against the Lift Assist Housing and tighten. This provides a secure stow and holds the motor in place during transportation when it is subject to high levels of shock and vibration. Failure to secure the motor may result in injury or damage to the unit.

Fall Away Ramps
The Fall Away Ramps hold the Lower Unit when the Motor is stowed and rotate to release the Lower Unit as the unit is being deployed. When the Stow Deploy Lever is pressed it unlocks the position of the Fall Away Ramps and the Ramps rotate to guide the Lower Unit back onto the mount when the motor is stowed.
Power Button

WARNING
When stowing or deploying the motor, keep fingers clear of all hinge and pivot points and all moving parts.

The Power button is located on the Indicator Panel on the Mount. The Terrova must be manually powered “on” and “off”. When the Motor is powered “on”, the Power Indicator will be illuminated green . When the Motor is powered “off”, the Power Indicator will not be illuminated .

28 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

STOWING AND DEPLOYING THE MOTOR

CAUTION

For safety reasons, disconnect the motor from the battery/batteries when the motor is not in use or while the battery/batteries are being charged. If the motor control is left on and the propeller rotation is blocked, severe motor damage can result.

AutoPilot

The AutoPilot Indicator is located on the Indicator Panel on the Mount. It is illuminated green illuminated when AutoPilot is not engaged.
Stow Deploy Lever

when AutoPilot is engaged and it is not

The Stow Deploy Lever is located at the top of the mount. The Stow Deploy Lever functions to unlatch the Fall Away Ramps which rotate to guide the Lower Unit. The Stow Deploy Lever is actuated by pressing it down.

STOWING AND DEPLOYING THE MOTOR
To Deploy the Motor
Loosen the Depth Collar, then push firmly down on the Stow Deploy Lever to release the Lift Assist Collar and slide the motor forward, out from the Fall Away Ramp. Lower the motor to the desired depth. Make sure it clicks into a secure, vertical position. Once at the desired depth, slide the Depth Collar against the Lift Assist Housing and tighten.
To Stow the Motor
Loosen the Depth Collar and depress the Stow Deploy Lever. Raise the motor by pulling up on the Shaft or Control Head. Pull the motor toward the stern until it rests securely on the Fall Away Ramp and the Fall Away Ramps captures the Lower Unit. Slide the Depth Collar down and secure it against the top of the Lift Assist Housing to secure the motor in place and prevent accidental deployment.
PUSH-TO-TEST BATTERY METER
This motor is equipped with a Push-to-Test Battery Meter. The LED located on the Indicator Panel on the Mount of the motor. The Battery Meter provides an accurate display of the remaining charge in the battery. It is only accurate when the motor is off. The meter reads as follows:
· One light indicates recharge. · Two lights indicate low charge. · Three lights indicate good charge. · Four lights indicate full charge.

WARNING
When stowing or deploying the motor, keep fingers clear of all hinge and pivot points and all moving parts.
WARNING
The Control Head will create a pinch point if the Depth Collar Knob is loosened and the Control Head slides to the top of the Depth Collar. Grasp the Shaft and prevent it from sliding all the way down to prevent the pinch point. Practice proper ergonomics when stowing and deploying the motor to prevent injury.

Indicator Panel

Push-to-Test Battery Meter

WARNING

Moving parts can cut or crush. The Lift Assist Housing can come off of Steering Housing and create a crushing hazard. Keep fingers clear of all moving parts.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 29

ADJUSTING THE DEPTH OF THE MOTOR

MOTOR ADJUSTMENTS

ADJUSTING THE DEPTH OF THE MOTOR
Once the boat is on the water, it may be necessary to adjust the Lower Unit up or down to achieve an optimum depth for motor performance. When setting the depth of the motor, be sure the top of the motor is submerged at least 12″ below the surface of the water to avoid churning or agitation of surface water.

1

a. With the motor in the deployed position, locate

the Depth Collar on the Shaft above the Lift

Assist Housing.

b. While holding the Shaft, loosen the Depth Collar Knob until the Shaft can slide up and down freely.
WARNING

Depth Collar

Shaft Depth Collar Knob
Lift Assist Housing

The Control Head will create a pinch point if the Depth Collar Knob is loosened and the Control Head slides to the top of the Depth Collar. Grasp the Shaft and prevent it from sliding all the way down to prevent the pinch point.

2

c. Raise or lower the motor to the desired depth.

d. Turn the motor Control Head to the desired position.

e. Slide the Depth Collar against the Steering Housing and tighten the Depth Collar Knob to secure the motor in place.

NOTICE: Be sure the top of the motor is submerged at least 12″ below the surface of the water to avoid churning or agitation of surface water.

WARNING
The Lift Assist Housing contains a spring that may break from excessive wear. Watch for sharp points that can be a puncture hazard. Always use care when handling the motor.

Depth Collar

Control Head Shaft Depth Collar Knob Lift Assist Housing

12″ Minimum Depth

Propeller

Motor

30 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

ADJUSTING THE LOWER UNIT FOR A SECURE STOW

ADJUSTING THE LOWER UNIT FOR A SECURE STOW
When the Motor is stowed, the Lower Unit should rest on the Fall Away Ramps, a part of the Motor Mount. It is recommended to secure the motor using the following instructions to avoid damage to the motor and shaft from vibrations during transport.

1

a. Before transporting the boat over water or land, stow

the motor to determine where the Lower Unit rests

on the Fall Away Ramps.

Lower Unit

Lift Assist Housing

Depth Collar

Shaft

NOTICE: The correct positioning of the Lower Unit will place it directly on the Fall Away Ramps.
b. If the Lower Unit does not sit on the Fall Away Ramps, deploy the motor, and stow it again.

Fall Away Ramps

c. Be sure to press the Stow Deploy Lever and adjust the Motor to allow it to rest on the Fall Away Ramps.
CAUTION
The Lower Unit should be placed on the Mount Ramps every time the motor is transported. If the Lower Unit is improperly placed, either above or below the Motor Rest Area, damage to the Lower Unit or Shaft will occur and the Shaft will be incorrectly captured. Not following the recommended placement for the Lower Unit will cause damage to the product and void your product warranty.

Depth Collar Knob
NOTICE: Slide the Depth Collar down and secure it against the top of the Steering Housing when stowed to secure the motor in place and prevent accidental deployment.

WARNING
When the motor is being transported, it is important to place the Depth Collar snug against the Lift Assist Housing and tighten. This provides a secure stow and holds the motor in place during transportation when it is subject to high levels of shock and vibration. Failure to secure the motor may result in injury or damage to the unit.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 31

INSTALLING AN EXTERNAL TRANSDUCER

INSTALLING AN EXTERNAL TRANSDUCER

An external transducer is not included with your trolling motor. An external transducer can be installed onto motors that have Universal Sonar or motors that do not have a built in transducer. For more information on Universal Sonar, please visit minnkotamotors.com. Installing an external transducer is not recommended for motors with Built-in MEGA Down Imaging.

1

a. Mount the External Transducer according to

directions provided with the transducer.

b. Leave enough slack in the Transducer Cable between the Lower Unit and Control Head to allow the motor to properly stow and deploy.
c. Use two tie wrap cables to secure the Transducer Cable to the Shaft just above the Lift Assist Collar and just below the Control Head.
d. Run the Transducer Cable through the Coil Cord to the power supply.
CAUTION

Control Head Coil Cord Transducer Cable

Tie Wrap Cable

Not following the recommended wire routing for the Universal Sonar and External Transducer Cables may cause damage to the product and void your product warranty. Take care to test the length and placement of cable to be sure that there is enough slack where needed and that cables are free of being entangled in moving parts. Routing the cables in any way other than directed may cause damage to the cables by being pinched or severed.

Slack Tie Wrap
Cable

Lift Assist Collar

Lower Unit

External Transducer

32 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

USING THE FOOT PEDAL

CONTROLLING SPEED & STEERING WITH THE FOOT PEDAL

The foot pedal is used to operate the motor, and controls on the foot pedal are easy to operate by either foot or hand. A light touch is all that is necessary. The motor can also be controlled by an i-Pilot or i-Pilot Link remote, as well as any compatible Minn Kota remote. Please refer to the i-Pilot, i-Pilot Link or compatible remote manual on how the remote controls the motor. To learn more about accessories that are compatible with the Terrova, please visit minnkotamotors.com.

Indicator Panel AutoPilot/ Spot-Lock

Momentary ON

Heel/Toe Steering

Power Connection from Motor

Constant ON

Indicator Panel

AutoPilot ON/OFF

Speed Control

Constant Steer Left

Spot-Lock

Prop ON/OFF

Steer Right

Foot Pedal Connection

Motor Speed

The Speed Control knob is located on the right side of the Foot Pedal above the and Spot-Lock button. Turn the Speed Knob forward to increase speed and backwards to decrease speed. The Speed Control knob can be set in a range from 0 to 10. Speed can also be adjusted using the remote.
Spot-Lock

The Spot-Lock button is located on the bottom, right side of the Foot Pedal and is labeled with an anchor symbol. When the Spot-Lock button is pressed, the location of the motor is recorded to a temporary memory location. The blue light next to the Spot-Lock label
AUTOPILOT SPOT-LOCK
on the Indicator Panel is illuminated when Spot-Lock is engaged. To engage Spot-Lock press the Spot-Lock button, to disengage, press the Spot-Lock button again. When engaging Spot-Lock, a tone will be emitted. When disengaging Spot- Lock with the Spot-Lock button, no tone will be emitted. Steering the motor with the Foot Pedal or adjusting the speed using the Speed Knob will cancel Spot-Lock and a High-Low, High-Low, High-Low tone will be emitted. Spot-Lock can also be controlled with the remote. For more specific directions on how to use Spot-Lock, please refer to either the i-Pilot or i-Pilot Link Manual.
WARNING

You are responsible for the safe and prudent operation of your vessel. We have designed the Terrova to be an accurate and reliable tool that will enhance boat operation and improve your ability to catch fish. This product does not relieve you from the responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a permanent watch so you can respond to situations as they develop. You must always be prepared to regain manual control of your boat. Learn to operate your Terrova in an area free from hazards and obstacles.
Practice proper ergonomics when operating the foot pedal to prevent injury.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 33

USING THE FOOT PEDAL

Steer Right/Steer Left
The Steer Right and Steer Left buttons are located at the bottom of the Foot Pedal. They function to steer right and left. Holding the Steer Right or Steer Left buttons down will continue to steer the motor to the left or right. Small steering changes of less than one degree can be made by quickly tapping the Steer Right and Steer Left buttons. The position and direction of the Steering Head directly corresponds to the position of the motor. The direction of the motor can also be controlled with the remote.
Prop ON/OFF

CAUTION
The steering system is designed to turn your motor 360 degrees. Be careful to avoid overwrapping the Coil Cord around the trolling motor Shaft. Overwrapping the coil cord will cause damage and prevent operation.
NOTICE: The motor will not auto correct to drive straight when it encounters an obstruction.

The Prop ON/OFF button is located in the bottom, middle of the Foot Pedal. It functions to turn the Prop on and off. The Prop will turn on when pressure is applied and turn off when pressure to the button is removed.

Constant

The Constant button

is located on the left side of the Foot Pedal, towards the bottom, right below the AutoPilot button. It functions

to toggle the motor between Constant Motor Operation and Momentary Motor Operation. The green light on the Indicator Panel will CONSTANT
be illuminated when the motor is in Constant Motor Operation. In Constant Mode, the propeller will continually run, regardless of whether

or not force is being applied to the Momentary button or Prop ON/OFF button. While in Constant Motor Operation, the propeller will run

continuously at the speed set by the Speed Control knob, or by the i-Pilot or i-Pilot Link remote.

If a propeller encounters an obstruction while either in Momentary or Constant Mode, while the propeller is running, the increased electrical current being generated by the obstruction will signal the motor to decrease the power to the propeller to prevent damage. If the current overload is detected for more than 20 seconds, the prop will be disabled to prevent damage to the motor. In this event, the operator can turn the prop back on after being sure that the obstruction has been cleared.

AutoPilot

The AutoPilot button is located in the middle, on the left side of the Foot Pedal. Pressing the AutoPilot button toggles the feature on
and off for motor that are installed with this feature. The red light on the Indicator Panel is illuminated when this feature is engaged. AUTOPILOT SPOT- LOCK
When AutoPilot is initiated from the Foot Pedal, the default AutoPilot mode is determined by the remote. AutoPilot can also be engaged
and disengaged using the remote. For more specific directions on how to use AutoPilot, please refer to either the i-Pilot or i-Pilot Link
Manual. The AutoPilot Indicator on the Mount will also be illuminated when AutoPilot is engaged.

Momentary

In Momentary Motor Operation, the propeller will only run while downward force is applied to the Momentary button. The Momentary button is on the Toe End of the Heel/Toe Steering pedal. Applying downward pressure to the Momentary button will turn the propeller on. The motor will then run at the speed set by the Speed Knob or remote. Removing downward force to the Momentary button will turn the propeller off. No indicator light is associated with the Momentary button. The Momentary button functions very similar to the Prop ON/OFF button.

Heel/Toe Steering

Push the Toe End of the Foot Pedal down to turn right and push the Heel End of the Foot Pedal down to turn left. The position and direction of the Control Head directly corresponds to the position of the motor. You must use your foot on the pedal to control the steering direction during manual operation. The direction of the motor can also be controlled with the remote.

Steering in Reverse

The propeller always turns in the forward direction. You can reverse the direction of thrust by turning the motor 180°.

34 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

SERVICE & MAINTENANCE

PROPELLER REPLACEMENT
TOOLS AND RESOURCES REQUIRED · 9/16″ Open End Wrench
INSTALLATION

· Flat Blade Screwdriver

1

a. Disconnect the motor from all sources of power prior

to changing the propeller.

b. Hold the propeller and loosen the Prop Nut with a pliers or a wrench.

c. Remove the Prop Nut and Prop Washer.

Drive Pin

Armature Shaft Propeller

NOTICE: If the Drive Pin is sheared or broken, you will need to hold the shaft stationary with a flat blade screwdriver pressed into the slot on the end of the shaft while you loosen the Prop Nut.

Prop Washer

Prop Nut

CAUTION

Disconnect the motor from the battery before beginning any prop work or maintenance.

2

d. Turn the old prop to horizontal and pull it straight off.

If drive pin falls out, push it back in.

CAUTION

If the prop does not readily slide off, take care to not bend the Armature Shaft while removing the prop by pulling the prop evenly off the Armature Shaft.

Propeller

3

e. Align the new Propeller with the Drive Pin.

f. Install the Prop Washer and Prop Nut.

g. Tighten the Prop Nut 1/4 turn past snug at 25-35 inch-lbs.
CAUTION

Do not over tighten as this can damage the prop.

Prop Nut Prop Washer
Propeller

Drive Pin

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 35

SERVICE & MAINTAINANCE
GENERAL MAINTENANCE
· After use, the entire motor should be rinsed with freshwater. This series of motors is not equipped for saltwater exposure. · The composite shaft requires periodic cleaning and lubrication for proper retraction and deployment. A coating of an aqueous-based
silicone spray will improve operation. · The propeller must be inspected and cleaned of weeds and fishing line after every use. Fishing line and weeds can get behind the
prop, damage the seals and allow water to enter the motor. · Verify that the prop nut is secure each time the motor is used. · To prevent accidental damage during transportation or storage, disconnect the battery whenever the motor is off of the water. For
prolonged storage, lightly coat all metal parts with an aqueous-based silicone spray. · For maximum battery life, recharge the battery(s) as soon as possible after use. For maximum motor performance, restore the battery
to full charge prior to use. · Keep battery terminals clean with fine sandpaper or emery cloth. · The propeller is designed to provide weed-free operation with very high efficiency. To maintain this top performance, the leading edge
of the blades must be kept smooth. If they are rough or nicked from use, restore to smoothness by sanding with fine sandpaper.
TROUBLESHOOTING
1. Motor fails to run or lacks power: · Check battery connections for proper polarity. · Make sure terminals are clean and corrosion-free. Use fine sandpaper or emery cloth to clean terminals. · Check battery water level. Add water if needed.
2. Motor loses power after a short running time: · Check battery charge. If low, restore to full charge.
3. Motor is difficult to steer: · Loosen the steering tension knob on the bracket. · Lubricate the composite shaft.
4. You experience prop vibration during normal operation: · Remove and rotate the prop 180°. See removal instructions in the “Propeller Replacement” section.
5. Experiencing interference with your fishfinder: · You may, in some applications, experience interference in your depth finder display. We recommend that you use a separate deepcycle marine battery for your trolling motor and that you power the depth finder from the starting/cranking battery. If problems still persist, call our service department at 1-800-227-6433.
NOTICE: For all other malfunctions, visit an Authorized Service Center. You can search for an Authorized Service Center in your area by visiting minnkotamotors.com, or by calling our customer service number at 1-800-227-6433.

36 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

SERVICE & MAINTAINANCE
FOR FURTHER TROUBLESHOOTING AND REPAIR
We offer several options to help you troubleshoot and/or repair your product. Please read through the options listed below.
Buy Parts Online
You can buy parts online directly from our website at minnkotamotors.com. From screws to sideplates, you can order replacement parts for your Minn Kota products.
Frequently Asked Questions
Find answers to general inquiries, battery and rigging installation, and networking scenarios. We have FAQs available on our website at minnkotamotors.com to help answer all of your Minn Kota questions.
Call Us (for U.S. and Canada)
Our consumer service representatives are available Monday ­ Friday between 7:00 a.m. ­ 4:30 p.m. CST at 800-227-6433. If you are calling to order parts, please have the 11-character serial number from your product, specific part numbers, and credit card information available. This will help expedite your call and allow us to provide you with the best consumer service possible. You can reference the parts list located in your manual to identify the specific part numbers.
Contact Us
You can contact our consumer service department with questions regarding your Minn Kota products. To inquire, visit minnkotamotors.com.
Authorized Service Centers
Minn Kota has over 800 authorized service centers in the United States and Canada where you can purchase parts or get your products repaired. Please visit our website to locate a service center in your area.

©2022 Johnson Outdoors Marine Electronics, Inc.

Scan to visit Minn Kota service online.
minnkotamotors.com | 37

COMPLIANCE STATEMENTS
ENVIRONMENTAL COMPLIANCE STATEMENT
It is the intention of JOME to be a responsible corporate citizen, operating in compliance with known and applicable environmental regulations, and a good neighbor in the communities where we make or sell our products.
WEEE DIRECTIVE
EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE designed and intended as fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other household refuse. It must be disposed of and collected for recycling and recovery of waste EEE. Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply in the collection, treatment, recovery, and environmentally sound disposal of those products; however, these requirements do vary within European Union member states. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased.
DISPOSAL
Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements the WEEE directive. Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of your local town council.
Never dispose of battery in a garbage bin. Comply with the disposal directions of the manufacturer or his representative and dispose of them at the proper place of collection of your local town council.
REGULATORY COMPLIANCE INFORMATION
i-Pilot Equipped Motors
For regulatory information on motors that come factory installed with i-Pilot, please refer to the i-Pilot Owner’s Manual online at minnkotamotors.com.
i-Pilot Link Equipped Motors
For regulatory information on motors that come factory installed with i-Pilot Link, please refer to the i-Pilot Link Owner’s Manual online at minnkotamotors.com.

38 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

FCC COMPLIANCE
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Johnson Outdoors Marine Electronics, Inc. could void the user’s authority to operate this equipment.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA COMPLIANCE
This product meets the applicable Industry Canada technical specifications. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Johnson Outdoors Marine Electronics, Inc. could void the user’s authority to operate this equipment.
ENVIRONMENTAL RATINGS
Ambient operating temperature range: -10C to 50C Ambient operating humidity range: 5% to 95% Maximum operating altitude: 10,000 feet

CE MASTER USER MANUAL (FOR CE CERTIFIED MODELS) ©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 39

PARTS DIAGRAM & PARTS LIST

TERROVA – 55/80/112 LBS THRUST – 12/24/36 VOLT – 45″/54″/60″/72″ SHAFT
T rts diagram and parts list provides Minn Kota® WEEE compliance disassembly instructions. For more information about where
you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased. Tools required, but not limited to: flat head screwdriver, Phillips screwdriver, socket set, pliers, wire cutters.
TERROVA CONTROL HEAD
Control Head Parts Diagram

44

28

XM YN 26

14 20

46 22 12
30

18

8

30
10
2 6
4

42 24
W V
16
38 34
36

40 32

40 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

PARTS DIAGRAM & PARTS LIST

Control Head Parts List

Assembly M N V W X Y
Item p p 2 4 6 8 10 12 14
16
p 18 p 20 22 24 26
28
30 32 34 36 38 40 p p

Part #
2774176 t 2774177 Â 2994075 t 2994076 Â 2770233 t 2770234 Â
Part #

2321505 2321702 2260905 2292500 2332102 2333101 2065400 2211415 Ì 490507-1 â 2256300 2224706 9950433 2218201 2375400 2290217
2395545 t 2395547  2372100 2390800 t 2375901  2373241  490389-1  2996400 2397106 t 2397107 Â

Description
MOTOR KIT, iPLT 1.6 TRV,UTX MOTOR KIT, iPLT 3.0 TRV,UTX REMOTE ASSY, IPILOT 1.6 REMOTE ASSY, IPILOT LINK COVER KIT, iPLT 1.6 TRV, ULTREX COVER KIT, iPLT 3.0 TRV, ULTREX
Description
SEAL,BUNG LOWER SEAL,BUNG UPPER,FW DEPTH COLLAR, LIFT ASSIST WASHER-FLAT .375 NYLON KNOB-SOFT GRIP,HG/DR,ZNC CONTROL BOX, ULTREX SCREW-#10-24 X 1-3/4 PPH SS NUT-HEX #10-24 UNC-2B NYL SS WIRE INSULATOR-LGE 1-3/4, BLUE CABLE-EXTENSION, 110″ CABLE, ADP-INT MDI 14 M12-120″ TIE WRAP-5.5″ BLACK INSERT-PLUG TIE WRAP-4″ BLACK FUSE HOLDER ASSEMBLY SHRINK TUBE-1/4OD X 1-3/4 COVER,CTRL BOX CVR, CTRL BX IP DECAL, DOMED, iPILOT FW DECAL, DOMED, iPILOT LINK FW SCREW-#8-18 X 5/8 THD (SS) LANYARD, REMOTE W/ CARABINER ADAPTER, USB DC POWER CABLE, USB REMOTE CHARGER CABLE, ETHERNET, 30′ HEADING SENSOR ASSEMBLY QUICK – QUICK REF, iPILOT 1.6 QUICK – QUICK REF, iPILOT 3.0

Notes i-PILOT RECEIVER i-PILOT LINK RECEIVER i-PILOT LINK ONLY i-PILOT COVER & DECALS ONLY i-PILOT LINK COVER & DECALS ONLY Notes
US2
LINK ONLY LINK ONLY LINK ONLY SELECT MODELS ONLY

Quantity
1 1 1 1 1 1
Quantity
1 1 1 1 1 1 1 1 2 1 1 2 1 2 1 2 1 1 1 1 4 1 1 1 1 1 1 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
©2022 Johnson Outdoors Marine Electronics, Inc.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
minnkotamotors.com | 41

PARTS DIAGRAM & PARTS LIST

Item

Part #

Description

2325631

DECAL, COVER, TERROVA 55

42

2325632

DECAL, COVER, TERROVA 80

2395550

DECAL, PUSH BTN TOP, T2/iP 55

44

2395554

DECAL, PUSH BTN TOP, T2/iP 80

2325634

DECAL, PUSH BTN TOP, TRV/iP 112

46

2372103

SCREW. #6 x 3/8 PLASTITE

p

2327130

MANUAL TERROVA BT FW

p

2397100

MANUAL, iPILOT 1.6

p

2327133

INSTALLATION INSTRUCTIONS TERROVA FW BT

p

2397102

MANUAL, iPILOT LINK 3.0

p

2297165

MANUAL – DISCLAIMER, DOWNLOAD INFO

p

2394900

INSTRUCTION HEADING SENSOR

p

2215700

LABEL, DI CABLE EXIT LOCATION

Notes 55LB THRUST 80LB THRUST 55LB THRUST 80LB THRUST 112LB THRUST
SELECT MODELS ONLY

Quantity
1 1 1 1 1 2 1 1 1 1 1 1 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
42 | minnkotamotors.com

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
©2022 Johnson Outdoors Marine Electronics, Inc.

TERROVA MOTOR
12 Volt 3.625″ Motor Parts Diagram

PARTS DIAGRAM & PARTS LIST

84 80
112 82 114
S

50

94

64 62

BB 52
54
56 58

48 108 106

110

104 118 112

98 90

114 88

82 78 116 84

92 74

A

C

66

60

70 96

86

102

100

72

60

86

76

80 66

E

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 43

PARTS DIAGRAM & PARTS LIST

12 Volt 3.625″ Motor Parts List

Assembly A C E BB S
Item 48
50
52 54 56 58 60
62
64
66
70
72 74
76
78 80 82 84 86 88 90 92
94
96

Part #
2779032 Ì 2779024 2779033 Ì 1378131 2888460
Part #
2323110
2092600 2151726 2053101 2091161 975-040 640-006 640-023 640-151 640-115 188-036 2-600-217 2-600-018 725-050
421-050
Ì 2-400-101A
337-036 701-008 701-081 830-007 830-008 990-067 990-070 640-316 640-315 2302102 Ì

Description
MTR/TUBE ASM 55# 45″ TRV/US2 BT MTR/TUBE ASM 55# 54″ TRV BT MTR/TUBE ASM 55# 54″ TRV/US2 BT PROP IND 2091160 WDLS WDG II SEAL & O-RING KIT
Description
NUT-HEX, 6-32 NYLOK SS TUBE-COMP,BLK,45″,1/4″ WALL,T2 TUBE-COMP,BLK,54″,1/4″ WALL,T2 PIN-DRIVE 1.06″ LG (SS) WASHER-5/16 STD (S/S) NUT-PROP,NYLOC (MED) 5/16 SS PROP-WW2 3 5/8″ MACHINED SPRING – TORSION LEADWIRE BLK 10 AWG 61 3/4″ GPT LEADWIRE BLK 10 AWG 69″ GPT LEADWIRE RED 10 AWG 70.375 GPT LEADWIRE RED 10 AWG 61 3/4″ GPT BRUSH ASSEMBLY BRUSH PLATE ASSEMBLY BRUSH PLATE ASSEMBLY PAPER TUBE – BRUSH RETENTION CTR HSG ASY 3.62 FW-MAGNET CB HSG BRSH END FW CB HSG BRSH END FW CB PLAIN END HSG ASY GASKET O-RING O-RING SCREW, # 8-32 THRU BOLT 10-32 x 9.205 WASHER – STEEL THRUST WASHER – NYLATRON LEADWIRE BROWN 18 AWG 71″ GPT LEADWIRE BROWN 18 AWG 62″ GPT SCREW-#6-20 X 1/2 THD CUTS

Notes
45 3.625 UNIVERSAL SONAR 54 3.625 54 3.625 UNIVERSAL SONAR 55LB THRUST 3.625 55LB THRUST 3.625
Notes
45″ 54″ 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 45″ 3.625 55LB THRUST 54″ 3.625 55LB THRUST 54″ 45″ 55LB THRUST 3.625 54″ 45″ 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 NON US2 55LB THRUST 3.625 US2 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 55LB THRUST 3.625 54″ 55LB THRUST 3.625 45″

Quantity
1 1 1 1 1
Quantity
1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 2 2 1 1 1 1 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
44 | minnkotamotors.com

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
©2022 Johnson Outdoors Marine Electronics, Inc.

Item

Part #

Description

98

788-015

RETAINING RING

100

140-010

BREARING

102

2-100-146 ARM ASY 12V 3.62 55#CB/LS

104

3393450

SCREW-#6-19 X.75 PPH HI-LOW SS

106

2323429

SCREW #6-32 X .50″ SS BHCS

108

2321523

COLLAR-FRONT, LIFT ASSIST, FW

110

2321527

COLLAR-BACK, LIFT ASSIST, FW

112

880-003

SEAL

114

880-006

SEAL WITH SHIELD

p

Ì

TRANSDUCER ASSY 73″ GEN2.5 W/T 54″

p

Ì

TRANSDUCER ASSY 67″ GEN2.5 W/T

116

144-049

BEARING – FLANGE

118

725-035

PAPER TUBE – SEAL BORE

PARTS DIAGRAM & PARTS LIST

Notes 3.625
55LB THRUST 3.625

Quantity
1 1 1 4 1 1 1 1 1 1 1 1 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
©2022 Johnson Outdoors Marine Electronics, Inc.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
minnkotamotors.com | 45

PARTS DIAGRAM & PARTS LIST
24 Volt 4″ Motor Parts Diagram

CC 136 134
132

162 164

142

190

144 148

T

138 140

200 204 198

120 202

DDD FFF
176

196

188

156

194

172 168 178

166

130 192

150

170 146

162 164 154

164

190

178

138

GR

174
182 158
152 180 KK MM LL NN 184 186 160

46 | minnkotamotors.com

BL

FJ

P

QZ 128

184 126 122

124

K GG SS

©2022 Johnson Outdoors Marine Electronics, Inc.

PARTS DIAGRAM & PARTS LIST

24 Volt 4″ Motor Parts List

Assembly B F G J L P Q R Z
DDD FFF CC T KK LL MM NN K GG SS Item
120
122 124 126 128 130 132 134

Part # 2777018 2777038 2777006 2777012 2777041 2777019 2777039 2777007 2777014 2777196 2777197 1378132 2889460 9421-290 9421-287 9421-288 9421-291 2777134 2777130 2777132
Part #
830-110 230-039 792-001 2262658 2091701 2093101

Description

Notes

MTR/TUBE ASM 80# 45″ TRV/US2 BT MTR/TUBE ASM 80# 54″ TRV/US2 BT MTR/TUBE ASM 80# 60″ TRV BT MTR/TUBE ASM 80# 60″ TRV/US2 BT MTR/TUBE ASM 80# 72″ TRV/US2 BT MTR/TUBE 80# 45″ TRV/US2-M BT MTR/TUBE 80# 54″ TRV/US2-M BT MTR/TUBE ASM 80# 60″ TRV-M BT MTR/TUBE 80# 60″ TRV/US2-M BT

45 4.0 UNIVERSAL SONAR 54 4.0 UNIVERSAL SONAR 60 4.0 60 4.0 UNIVERSAL SONAR 72 4.0 UNIVERSAL SONAR 45 4.0 UNIVERSAL SONAR EUROPE ONLY 54 4.0 UNIVERSAL SONAR EUROPE ONLY 60 4.0 EUROPE ONLY 60 4.0 UNIVERSAL SONAR EUROPE ONLY

CTR HSG, CB, 80#, FW, UP TO 60″ CTR HSG, CB, 80#, FW, 72″ TUBE PROP IND 2331160 WDLS WDG II SEAL & O-RING KIT PLN END HSG/TRANDUCER ASY 4.0 PLN END HSG/TRANDUCER ASY 4.0 PLN END HSG/TRANDUCER ASY 4.0 PLN END HSG/TRANDUCER ASY 4.0 MTR/TUBE ASM 80# 72″ TRV/MDI BT MTR/TUBE ASM 80# 45″ TRV/MDI BT MTR/TUBE ASM 80# 60″ TRV/MDI BT

TUBE TUBE 80LB THRUST 4 80LB THRUST 4 80LB THRUST 60″ TRANSDUCER UNIVERSAL SONAR 80LB THRUST 45″ TRANSDUCER UNIVERSAL SONAR 80LB THRUST 54″ TRANSDUCER UNIVERSAL SONAR 80LB THRUST 72″ TRANSDUCER UNIVERSAL SONAR 80LB THRUST 72″ BUILT-IN MEGA DOWN IMAGING 80LB THRUST 45″ BUILT-IN MEGA DOWN IMAGING 80LB THRUST 60″ BUILT-IN MEGA DOWN IMAGING

Description

Notes

TUBE-CMP,BLK,45″,1/4″ WLL TUBE-CMP,BLK,45″,1/4″,MDI TUBE-CMP,BLK,60″,1/4″ WLL TUBE-CMP,BLK,54″,1/4″ WLL TUBE-CMP,BLK,72″,1/4″ WLL TUBE-CMP,BLK,45″,1/4″,”M” TUBE-CMP,BLK,60″,1/4″,MDI TUBE-CMP,BLK,60″,1/4″,”M” PLAIN END HOUSING, PNT 4.0 DI SCREW-5-16-18 X 5/8 SHCS SS CABLE CLAMP, 1/4″ STEEL GUARD, TRANSDUCER, PNT 4.0 DI PIN-DRIVE 1″ X 3/16″ S/S WASHER-PROP (LARGE) NUT-PROP,NYLOC,LG, 3/8 SS

BUILT-IN MEGA DOWN IMAGING BUILT-IN MEGA DOWN IMAGING UNIVERSAL SONAR BUILT-IN MEGA DOWN IMAGING 80LB THRUST 4 112LB THRUST 4.5 80LB THRUST 4 112LB THRUST 4.5 80LB THRUST 4 112LB THRUST 4.5

Quantity
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Quantity
1 1 1 1 1 1 1 1 1 2 1 1 1 1 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 47

PARTS DIAGRAM & PARTS LIST

Item

Part #

Description

Notes

Quantity

136

2331160

PROP-WW2 (4″) w/ADP.RING

80LB THRUST 4.0

1

138

188-094

BRUSH W/TERMINAL

80LB THRUST 4.0

2

140

975-041

SPRING – TORSION

80LB THRUST 4.0

2

640-016

LEADWIRE BLK 10 AWG 56 1/2 XLP

1

640-053

LEADWIRE BLK 10 AWG 82.375 XLP 80LB THRUST 4.0

1

142

640-052

LEADWIRE BLK 10 AWG 70.125 XLP 80LB THRUST 4.0

1

640-022

LEADWIRE BLK 10 AWG 72.5 XLP

80LB THRUST 4.0

1

640-148

LEADWIRE RED 10 AWG 83″ GPT

80LB THRUST 4.0

1

640-152

LEADWIRE RED 10 AWG 69.625 XLP 80LB THRUST 4.0

1

144

640-118

LEADWIRE RED 10 AWG 56 XLP

80LB THRUST 4.0

1

640-126

LEADWIRE RED 10 AWG 71″ XLP

80LB THRUST 4.0

1

p

BRUSH HOLDER

80LB THRUST 4.0

2

9-738-015 BRUSH PLATE 4″ TERMINAL

80LB THRUST 4.0

1

2-600-176 BRUSH PLATE ASM 4″ ELEC. CB

1

146

2-600-155 BRUSH PLATE ASM 4″ ELEC.66″ CB

1

2-600-196 BRUSH PLATE ASSEMBLY 4″

1

2-600-195 BRUSH PLATE ASSEMBLY 4″

1

p

2260730

CONNECTOR 1/4 MALE TAB QD

80LB THRUST 4.0

2

148

BEAD-FERRITE

1

150

2-100-214 ARM ASSY 24V 4″ 80# (WW2)

80LB THRUST 4.0

1

152

140-010

BEARING – BALL

55LB THRUST 3.625 80LB THRUST 4.0

1

154

CTR HSG ASY 4.0 FW MGNTZ

80LB THRUST 4.0

1

2-300-170 BRUSH END HSG ASY 4.0 FW

80LB THRUST 4.0

1

156

420-070

HSG BRSH END 4.0 FW CB (SUB)

1

421-070

HSG BRSH END 4.0 FW CB

1

158

421-276

HSG PLN END 4″ PAINTED FW BS

80LB THRUST 4.0 NON US2 NON MDI

1

160

PLAIN END HSG-PNTD-4″US2.5 CB 80LB THRUST 4.0 UNIVERSAL SONAR

1

162

701-009

O-RING

80LB THRUST 4.0

2

164

701-043

O-RING

80LB THRUST 4.0

2

166

830-027

SCREW – SELF-THREAD 10-32X2.25 80LB THRUST 4.0

2

168

830-095

THRU BOLT 12-24 x 9.79

80LB THRUST 4.0

2

170

990-051

WASHER – STEEL THRUST

80LB THRUST 4.0 112LB THRUST 4.5

1

172

990-052

WASHER – NYLATRON

80LB THRUST 4.0 112LB THRUST 4.5

1

640-316

LEADWIRE BROWN 18 AWG 71″ GPT 55LB THRUST 3.625 80LB THRUST 4.0 112LB THRUST 4.5

1

174

640-315

LEADWIRE BROWN 18 AWG 62″ GPT 80LB THRUST 4.0

1

640-317

LEADWIRE BROWN 18 AWG 86″ GPT 80LB THRUST 4.0 112LB THRUST 4.5

1

176

582-013

CLIP, RETAINING SHORT

80LB THRUST 4.0

1

178

973-025

SPACER – BRUSHPLATE

80LB THRUST 4.0

2

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.

48 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

PARTS DIAGRAM & PARTS LIST

Item

Part #

Description

Notes

Quantity

180

992-010

WASHER – BELLEVILLE

80LB THRUST 4.0

2

182

990-045

SPACER – THRUST

80LB THRUST 4.0

1

184

2302104

SCREW-#6-20 X 3/8 THD CUTS

80LB THRUST 4.0 112LB THRUST 4.5

1

186

230-038

CABLE CLAMP

80LB THRUST 4.0 112LB THRUST 4.5 UNIVERSAL SONAR

1

188

788-040

RETAINING RING

1

190

880-025

SEAL

2

725-095

PAPER TUBE, SEAL

1

192

725-035

PAPER TUBE, SEAL

1

194

144-017

BEARING, FLANGE

1

p

RIVET – .25″

4 80LB THRUST 4.5 112LB THRUST

6

196

3393450

SCREW-#6-19 X.75 PPH HI-LOW SS

4

198

2323429

SCREW #6-32 X .50″ SS BHCS

1

200

2321523

COLLAR-FRONT, LIFT ASSIST, FW

1

202

2321527

COLLAR-BACK, LIFT ASSIST, FW

1

204

2323110

NUT-HEX, 6-32 NYLOK SS

1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
©2022 Johnson Outdoors Marine Electronics, Inc.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
minnkotamotors.com | 49

PARTS DIAGRAM & PARTS LIST
36 Volt 4.5″ Motor Parts Diagram

244

262 266 264

242

290

276 220

DD

292

232

230

234

290

236

258

U

298

240

304

302

300

238

268 296

294 272 250

262

278 CCC EEE 288

248 266 256

264

274 246 270

240

238

D H LLL

PP QQ RR 282 284

252

254

286 260

280

TT UU 282 224 226

222

228

WW XX

50 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

PARTS DIAGRAM & PARTS LIST

36 Volt 4.5″ Motor Parts List

Assembly D H LLL
CCC EEE DD U PP QQ RR TT UU WW XX Item
220
222 224 226 228 230 232 234 236 238 240
242

Part # 2777090 2777078 2777079 2777241 2777242 1378160 2881450 9421-246 9421-245 9421-247 2773005 2773006 2777152 2777154
Part #
830-110 230-039 792-005 2262658 2091701 2093101 2341160 188-095 975-045 640-021 640-049 640-045

Description
MTR/TUBE 112# 54″ TRV/US2 BT MTR/TUBE 112# 60″ TRV/US2 BT MTR/TUBE 112# 72″ TRV/US2 BT CTR HSG, CB, 112#, FW, UP TO 60″ CTR HSG, CB, 112#, FW, 72″ TUBE PROP KIT 2341160 112# WW2 SEAL & O-RING KIT PLN END HSG/TRANDUCER ASY 4.5 PLN END HSG/TRANDUCER ASY 4.5 PLN END HSG/TRANDUCER ASY 4.5 PLN END HSG/TRNDCR 4.5 MDI PLN END HSG/TRNDCR 4.5 MDI MTR/TUBE ASM 112#60″TRV/MDI BT MTR/TUBE ASM 112#72″TRV/MDI BT
Description
TUBE-CMP,BLK,45″,1/4″ WLL TUBE-CMP,BLK,45″,1/4″,MDI TUBE-CMP,BLK,60″,1/4″ WLL TUBE-CMP,BLK,54″,1/4″ WLL TUBE-CMP,BLK,72″,1/4″ WLL TUBE-CMP,BLK,45″,1/4″,”M” TUBE-CMP,BLK,60″,1/4″,MDI TUBE-CMP,BLK,60″,1/4″,”M” SCREW-5-16-18 X 5/8 SHCS SS CABLE CLAMP, 1/4″ STEEL PLAIN END HOUSING, PNT 4.5 DI GUARD, TRANSDUCER, PNT 4.5 DI PIN-DRIVE 1″ X 3/16″ S/S WASHER-PROP (LARGE) NUT-PROP,NYLOC,LG, 3/8 SS PROP-WW2 (4.5) w/ADP.RING BRUSH SPRING – TORSION LEADWIRE BLK 10 AWG 69.5 XLP LEADWIRE BLK 10 AWG 88.50 GPT LEADWIRE BLK 10 AWG 76.5″ GPT

Notes 54 4.5 UNIVERSAL SONAR 60 4.5 UNIVERSAL SONAR 72 4.5 UNIVERSAL SONAR TUBE NON UNIVERSAL SONAR NON MDI TUBE NON UNIVERSAL SONAR NON MDI 112LB THRUST 4.5 112LB THRUST 4.5 112LB THRUST 60″ TRANSDUCER UNIVERSAL SONAR 112LB THRUST 54″ TRANSDUCER UNIVERSAL SONAR 112LB THRUST 72″ TRANSDUCER UNIVERSAL SONAR 112 LB THRUST 72″ TRANSDUCER BUILT-IN MEGA DOWN IMAGING 112 LB THRUST 60″ TRANSDUCER BUILT-IN MEGA DOWN IMAGING 60″ BUILT-IN MEGA DOWN IMAGING 72″ BUILT-IN MEGA DOWN IMAGING Notes
BUILT-IN MEGA DOWN IMAGING BUILT-IN MEGA DOWN IMAGING BUILT-IN MEGA DOWN IMAGING BUILT-IN MEGA DOWN IMAGING 80LB THRUST 4 112LB THRUST 4.5 80LB THRUST 4 112LB THRUST 4.5 80LB THRUST 4 112LB THRUST 4.5 112LB THRUST 4.5 112LB THRUST 4.5 112LB THRUST 4.5 112 LB THRUST 54″ 4.5 112LB THRUST 72″ 4.5 112LB THRUST 60″

Quantity
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Quantity
1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 2 1 1 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 51

PARTS DIAGRAM & PARTS LIST

Item

Part #

Description

Notes

Quantity

640-149 LEADWIRE RED 10 AWG 88 GPT

4.5 112LB THRUST 72″

1

244

640-143 LEADWIRE RED 10 AWG 68 1/2″ GPT 112LB THRUST 54″

1

640-145 LEADWIRE RED 10 AWG 75 7/8″ GPT 112LB THRUST 60″

1

p

BRUSH HOLDER

112LB THRUST 4.5

2

9-738-011 BRUSH PLATE

112LB THRUST 4.5

1

246

2-600-244 BRUSH PLATE ASM 4.5″ HAND 62″ 112LB THRUST 4.5

1

2-600-249 BRUSH PLATE ASM 4.5″ 72″”

112LB THRUST 4.5

1

248

2260731 TERMINAL 1/4″ MALE TAB-THREE

112LB THRUST 4.5

2

250

2307312 BEAD-FERRITE

1

252

2-100-245 ARMATURE ASY 4.5″LWR UNIT

112LB THRUST 4.5

1

254

140-014 BEARING-BALL 6000

112LB THRUST 4.5

1

256

CTR HSG ASY 4.5″ MAG FW CB

112LB THRUST 4.5

1

258

2-300-155 BRUSH END HSG ASY 4.5″ FW

112LB THRUST 4.5

1

260

PLN END HSG 4.5″ US2.5 PNT FW

112LB THRUST 4.5

1

262

701-009 O-RING

112LB THRUST 4.5

2

264

701-098 O-RING, 98MM X 2MM

112LB THRUST 4.5

1

266

701-103 O-RING,103MM X 3.00MM, 70 BUNA 112LB THRUST 4.5

1

268

2053410 SCREW-#8-32 X 1/2 TRI-LOBE HEX 112LB THRUST 4.5

2

270

830-094 THRU BOLT 12-24 X10.31

80LB THRUST 4.0 112LB THRUST 4.5

2

272

990-051 WASHER – STEEL THRUST

80LB THRUST 4.0 112LB THRUST 4.5

1

274

990-052 WASHER – NYLATRON

80LB THRUST 4.0 112LB THRUST 4.5

1

640-316 LEADWIRE BROWN 18 AWG 71″ GPT 55LB THRUST 3.625 80LB THRUST 4.0 112LB THRUST 4.5

1

276

640-315 LEADWIRE BROWN 18 AWG 62″ GPT 80LB THRUST 4.0

1

640-317 LEADWIRE BROWN 18 AWG 86″ GPT 80LB THRUST 4.0 112LB THRUST 4.5

1

278

582-016 CLIP-RETAINING, SONAR

112LB THRUST 4.5

1

280

992-011 WASHER – BELLEVILLE

112LB THRUST 4.5

2

282

2302104 SCREW-#6-20 X 3/8 THD CUTS

80LB THRUST 4.0 112LB THRUST 4.5

1

284

230-038 CABLE CLAMP

80LB THRUST 4.0 112LB THRUST 4.5 UNIVERSAL SONAR

1

286

990-011 WASHER-SHIM OD 1″,ID.630″SS

112LB THRUST 4.5

1

288

788-040 RETAINING RING

1

290

880-025 SEAL

2

p

RIVET – .25″

4 80LB THRUST 4.5 112LB THRUST

6

292

725-035 PAPER TUBE, SEAL

1

294

144-017 BEARING, FLANGE

1

296

3393450 SCREW-#6-19 X.75 PPH HI-LOW SS

4

298

2323429 SCREW #6-32 X .50″ SS BHCS

1

300

2321523 COLLAR-FRONT, LIFT ASSIST, FW

1

302

2321527 COLLAR-BACK, LIFT ASSIST, FW

1

304

2323110 NUT-HEX, 6-32 NYLOK SS

1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
52 | minnkotamotors.com

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
©2022 Johnson Outdoors Marine Electronics, Inc.

PARTS DIAGRAM & PARTS LIST

TERROVA STEERING HOUSING
Steering Housing Parts Diagram

SSS
346 348 342
340 338 344

MMM NNN PPP

324 326

350 330
334

332 336

328 322

380 378

410
352 410
374

408

372
360
368 366 364 358

354 GGG

HHH

JJJ 356
358 364
366 322
362 360 370
320

376
382 384

378 380

374

374

VV QQQ RRR 400

388 390

392 394 404

398

406

396
386 402

412

419 417 418 416

KKK

414

414

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 53

PARTS DIAGRAM & PARTS LIST

Steering Housing Parts List

Assembly MMM NNN PPP VV QQQ RRR SSS GGG HHH JJJ KKK Item 320 322 324 326 328 330 332 334 336
338
340 342 344 346 348 350 352 354 356 358 360 362

Part #
2997060 2997061 2997062 2992727 2992728 2992729 2776561 2777060 2777061 2777062 2771522
Part #
2326566

2322210 2302250 2302255 2321730

2322215 2322520 2322525 2053422 2051710 2043412 2308601 2322030 2322200 2327308 2321704 2321510

Description
STEERING HSG ASM 12V FW STEERING HSG ASM 24V FW STEERING HSG ASM 36V FW LIFT ASSIST ASM 55# FW PA6 LIFT ASSIST ASM 80# FW PA6 LIFT ASSIST ASM 112# FW PA6 STEERING HSG TOP FW/GEAR KIT STEERING MOTOR KIT, 12V T2 STEERING MOTOR KIT, 24V T2 STEERING MOTOR KIT, 36V FW T2 COLLAR-FRONT/BACK, LIFT KT
Description
HOUSING-STEERING, BTM, FW PIN-ROLL 5/16″ X 1/2″ SHAFT-GEAR, FIRST CLUSTER SHAFT-GEAR,INTERMED.CLUSTER SHAFT-GEAR, THIRD CLUSTER GEAR & PINION, DR.HSG, STAGE 2 GEAR & PINION,DR. HSG, STAGE 3 GEAR & PINION,DR. HSG, STAGE 4 SPACER,GEAR CLUSTER MOTOR, STEERING 12V FW T2 MOTOR, STEERING 24V FW T2 MOTOR, STEERING 36V FW T2 GEAR-PINION, DR.HSG, STAGE 1 CASE-MOTOR,STRG HSG,TOP CASE- MOTOR,STRG HSG,BTM SCREW-X6 X /375 PLASTITE SS SPLIT LOCK WASHER 3MM SCREW-#8-18 X 3/4 TY AB SS PPH BREATHER FILTER, DR.HOUSING TUBE-OUTPUT, MACHINED GEAR-OUTPUT BEARING-BALL,SEALED WASHER-THRUST, STEERING COLLAR- DRIVE,BOTTOM

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
54 | minnkotamotors.com

Notes Notes

Quantity
1 1 1 1 1 1 1 1 1 1 1
Quantity
1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 2 2 1

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
©2022 Johnson Outdoors Marine Electronics, Inc.

Item

Part #

Description

364

2321720

SHIM,O-RING

366

2324608

O-RING,224, STR HSG

368

2321530

LINER OUTPUT TUBE,LFT AST

370

2324604

O-RING, CASE SEAL

372

HOUSING-STEERING, TOP, FW

374

2323408

SCREW-#8-32 X 2.0 SHCS SS

376

2322600

PIN-LATCH, ZP

378

2321702

WASHER-FLAT .375 NYLON

380

2263011

E-RING 3/8 DIA. SHAFT*

382

2322702

SPRING, LATCH PIN SS

384

2323410

SCREW-#8-32 X .75 SHCS SS

386

2326547

HOUSING-RIGHT, LIFT ASSIST PA6

388

2326542

HOUSING-LEFT, LIFT ASSIST PA6

2997900

ASM-HUB/SPRING, 55# SS

390

2997901

ASM-HUB/SPRING, 80# SS

2997902

ASM-HUB/SPRING, 112# SS

392

2322300

GUIDE,DR.DOG, LIFT ASSIST

394

2328605

ENGAGEMENT DOG, LIFT ASST

396

2322726

SPRING,COMPRESSION,.360″ OD SS

398

2322610

PIN-AXLE, LIFT ASSIST

400

2323430

SCREW-#10-24 X 1-3/8, PPH

402

2333101

NUT-HEX #10-24 UNC-2B NYL SS

404

2372103

SCREW-#6 X .375 PLASTITE SS

406

2321955

BRACKET, LIFT ASSIST

408

3393450

SCREW-#6-19 X .75 PPH HI-LO

410

2327310

BUSHING, PIVOT PIN

412

LEADWIRE, STEERING MOTOR

414

3393450

SCREW-#6-19 X.75 PPH HI-LOW SS

416

2323429

SCREW #6-32 X .50″ SS BHCS

417

2323110

NUT-HEX, 6-32 NYLOK SS

418

2321523

COLLAR-FRONT, LIFT ASSIST, FW

419

2321527

COLLAR-BACK, LIFT ASSIST, FW

PARTS DIAGRAM & PARTS LIST

Notes

Quantity
2 2 1 1 1 7 1 2 2 2 1 1 1 1 1 1 1 1 1 1 5 5 4 2 2 2 1 4 1 1 1 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
©2022 Johnson Outdoors Marine Electronics, Inc.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
minnkotamotors.com | 55

PARTS DIAGRAM & PARTS LIST

TERROVA FOOT PEDAL
Foot Pedal Parts Diagram

EE 466 462
56 | minnkotamotors.com

434
432 430

424 476
478 422

426 428
476
444 476
440
472 470 420
468

446 474
442 458
438 FF
442
444

464 476

464 460

452 456

452 456

454

456 454

456

©2022 Johnson Outdoors Marine Electronics, Inc.

PARTS DIAGRAM & PARTS LIST

Foot Pedal Parts List

Assembly
EE FF
Item
420 422 424 426 428 430 432 434 438 440 442 444 446 452 454 456 458 460 462 464 466 468 470 472 474 476 478

Part #
2994722 2994859
Part #
2323731 2323735 2323715 2323725 2203720 2320206 2325655 2324401 2322714 2328600 2321300 2223430 2323710 2322706 2323420 2301310 2325110 2204500
2373440 2332103 2302100 2322900 2372100 2320100 2322704 2323730

Description
FOOT PEDAL ASM, TRV BT BAG ASY-TERROVA/V2,RUB.BUMPERS
Description
BUTTON, RIGHT STEER, TERROVA BUTTON, MOMENTARY, TERROVA BUTTON,MOM/CON,FT PEDAL BUTTON,AP,FT PEDAL BUTTON, SPOT LOCK,ULTERRA/TRRV COVER,HEEL TOE FT PED,TRV DECAL, 3 INDICATORS, TERROVA PEDAL,HEEL/TOE FOOT PEDAL SPRING SS FLEX FINGER, FOOT PEDAL CLAMP, FT PEDAL SCREW-#8×3/4 PPH,TYPE 25,SS BUTTON,MOM,FT PEDAL SPRING-BARREL SS SCREW-#8-18 X 3/8″ PFH SS TY B SCREW-#8-18 X 1/2 (SS) PAD, FOOT PEDAL BASE PLATE-ULTERRA / TERROVA CONTROL BOARD ASSY, FOOT PEDAL, TERROVA SCREW-#4-24 X 1/4 PHCR SS TY B SCREW-#6-20 X 3/8 THD(SS) SCREW-#6-20 X 1/2 THD CUTS STRAIN RELIEF, FOOT PEDAL SCREW-#8-18 X 5/8 THD* (SS KNOB- SPEED, FOOT PEDAL SPRING, LARGE SHORT SS BUTTON, LEFT STEER, TERROVA

Notes Notes

Quantity
1 1
Quantity
1 1 1 1 1 1 1 1 1 1 2 4 1 2 2 11 5 1 1 4 2 2 1 2 1 6 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
©2022 Johnson Outdoors Marine Electronics, Inc.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
minnkotamotors.com | 57

PARTS DIAGRAM & PARTS LIST

TERROVA MOUNT
Mount Parts Diagram

590 580 578

582

558

AA

588

ZZ

AAA 608 604 586 BBB
606

600
596 602 598

614 574

YY

550

576 572

498 552

584

594

496

512

506
508 502

554

540

570

546 544
542 612

510

568

504

500

556

502

566

482

480

610

532 520 518

516

548 570 516 518

538

520

522

498 538548

544 546

542

528

514

592

594

530 552

614

58 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

PARTS DIAGRAM & PARTS LIST

Mount Parts List

Assembly YY ZZ AAA BBB AA Item 480 482 p 496 498 500 502 504 506 508 510 512 514 516 518 520
522
528
530
532
538 540 542 544 546

Part #
2774065 2774066 2774067 2774069 2994864
Part #
2321907 2322912 2325502 2322602 2013100 2320405 2322604 2071716 2322701 2301700 2073408 2321940 2321950 2323412 2321706 2325115 2323910 2323930 2323931 2994204 2321920 2321922 2323915 2323935 2323936 2324705 2994202 2322716 2321700 2323422

Description
CONTROL BRD, 12V TERROVA BT CTRL BRD, 24/36V TRV BT w/SHRNK CTRL BRD, 12V IP TRV BT w/SHRNK CTRL BRD, 24/36V IP TRV BT, SHRNK BAG ASSY-TERROVA/V2,MNTG HDW
Description
BASE, EXTRUSION, MACHINED PIN-ROLL .1875 X 1.000 SS DECAL, STOW / DEPLOY, T2 PIN-PIVOT, ZP NUT-SPEED HANDLE, RELEASE, FW BUSHING,HANDLE,GOBEIL WASHER-FLAT SS .253 x .470 SPRING, TORSION SPACER-RELEASE LEVER-BRASS SCREW-1/4-20 X 7/8 PPH S/S BRACKET, STRAIN RELIEF FW BRACKET, SIDEPLATE FW SCREW-#8-18 X .25 PPH SS TY B WASHER-FLAT #8 .50 OD/.188 SS PAD, RUBBER REST, BLACK RAMP-MOTOR, RIGHT 3-5/8″ RAMP-MOTOR, RIGHT 4″ RAMP-MOTOR, RIGHT 4.5″ ARM/SUPPORT BLOCK ASSY,R,FW PLATE-SKID, RIGHT FW PLATE-SKID, RIGHT FW RAMP-MOTOR, LEFT 3 5/8″ RAMP-MOTOR, LEFT 4″ RAMP-MOTOR, LEFT 4.5″ INSERT-MOTOR RAMP,METAL,ZP ARM/SUPPORT BLOCK ASSY,L,FW SPRING, EXTENSION, T2 WASHER #10 SS SCREW-#10-24 X .25″ PPH SS MCH

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
©2022 Johnson Outdoors Marine Electronics, Inc.

Notes NO SHRINKS SHRINK TUBES SHRINK TUBES i-PILOT/i-PILOT LINK SHRINK TUBES i-PILOT/i-PILOT LINK Notes
55LB THRUST 80LB THRUST 112LB THRUST 4.0 3.625 55LB THRUST 80LB THRUST 4.5 112LB THRUST 55LB THRUST 80LB THRUST 112LB THRUST

Quantity
1 1 1 1 1
Quantity
1 2 1 1 2 1 2 1 1 1 1 1 1 4 4 4 1 1 1 1 1 1 1 1 1 2 1 2 2 2

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
minnkotamotors.com | 59

PARTS DIAGRAM & PARTS LIST

Item

Part #

Description

548

2322920

STAND-OFF, ALUMINUM PLAIN

2321925

PLATE-SKID, LEFT FW

550

2331927

PLATE-SKID, LEFT FW

552

2323403

SCREW-1/4-20 X.375 MCH SS CRPH

554

2320217

COVER, HANDLE COSMETIC FW

556

2383446

SCREW-#8-16 X .50″ PLASTITE SS

558

2320830

LOCKING TAB,PWR/BAT.METER

p

2383428

SCREW-#4-24 X 3/8 HI-LO SS

p

2320203

CAP-DUST,CONNECTOR,FEMALE

p

2323406

SCREW-#10-24 X .50 CRPH SS

566

2090651

LEADWIRE,10 GA

568

2321310

STRAIN RELIEF

570

2323405

SCREW-1/4-20 X 1/2″ MCH SS

572

2307313

BEAD-FERRITE

2991274

COIL CORD ASSY 45″/48″ U.SONAR

2991272

COIL CORD ASY 54″/60″ U.SONAR

574

2991271

COIL CORD ASY 54″/60″ NON-US2

2991276

COIL CORD ASSY 72″ U.SONAR

576

2323927

SIDEPLATE-LEFT, TERROVA

578

2326530

HOUSING-CENTER, TERROVA

580

2325657

DECAL, B. MTR/CON/PWR/STATUS FW

2074070

BATTERY METER, 12V, FW

582

2074071

BATTERY METER, 24V, FW

2074072

BATTERY METER, 36V, FW

584

2320710

TERMINAL-AMP (T-TAB)

586

2325401

SHRINK TUBE-3/4 ID X 2″ W/ADHS

p

2321315

HOLDER-CONNECTOR,NYLON,BLACK

588

2383428

SCREW-#4-24 X 3/8 HI-LO SS

590

2322901

STRAIN RELIEF, HEYCO P/N 1852

592

2323922

SIDEPLATE-RIGHT, TERROVA

594

2323404

SCREW-1/4-20 X 1/2″ T-L ZP

596

2263462

SCREW-1/4-20 X 2″ S/S PPH ADJT

598

2263103

NUT-1/4-20 NYLOCK SS

600

2301720

WASHER-MOUNTING – RUBBER

602

2261713

WASHER-1/4 FLAT 18-8 SS

604

2305415

SHRINK TUBE-.472 ID X 2.25″

606

2305410

SHRINK TUBE-.315 OD X 2.25″

Notes 4.0 3.625 55LB THRUST 80LB THRUST 4.5 112LB THRUST
45″ 54″ NON US2 NON MDI 54″ 60″ 72″
55LB THRUST 80LB THRUST 112LB THRUST

Quantity
2 1 1 2 1 2 1 2 1 2 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 4 6 6 6 6 1 3

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
60 | minnkotamotors.com

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
©2022 Johnson Outdoors Marine Electronics, Inc.

PARTS DIAGRAM & PARTS LIST

Item

Part #

Description

608

2305401

SHRINK TUBE-.374 ID X `1.5″

610

2332104

SCREW-1/4-20 X 5/8 S/S

612

2323402

SCREW-1/4-20 X .375 T-L, ZP

614

2323405

SCREW-1/4-20 X 1/2″ MCH SS

p

2327130

MANUAL, TERROVA BT

p

2327132

MANUAL, INSTALL GUIDE, TRRV BT

p

2397100 t MANUAL, iPILOT 1.6

p

2397102 Â MANUAL, IPILOT 3.0

p

2297165

MANUAL – DISCLAIMER. DOWNLOAD INFO

Notes
ONLINE ONLINE ONLINE

Quantity
4 1 2 4 1 1 1 1 1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with i-Pilot.
©2022 Johnson Outdoors Marine Electronics, Inc.

 Only available with models factory installed with i-Pilot Link. Ì Only available with models factory installed with Universal Sonar. â Only available with models factory installed with Built-in MEGA Down Imaging.
minnkotamotors.com | 61

RECOMMENDED ACCESSORIES
ON-BOARD & PORTABLE BATTERY CHARGERS
Stop buying new batteries and start taking care of the ones you’ve got. Many chargers can actually damage your battery over time ­ creating shorter run times and shorter overall life. Digitally controlled Minn Kota chargers are designed to provide the fastest charge that protect and extend battery life.

MK212PC

MK210D

MK110PD

TALON SHALLOW WATER ANCHOR
Introducing the all-new, sleek redesigned Talon. Talon is the only shallow water anchor with up to 15′ of anchoring depth, multiple anchoring modes, and control from the bow, transom, console, remote or mobile device.

BUILT-IN WORK LIGHT
Lets you tie lines and work from the transom any time of day — or night. Includes both white and blue LED lights with three brightness settings.
BLUETOOTH® CONNECTIVITY
Lets you control Talon from your mobile device and easily update it. Also opens up communication to other control options.

UP TO 15′ DEEP
Control more water and catch more fish with the first 15′ shallow water anchor.
MORE CONTROL OPTIONS
· Control Panel · Wireless Remote · Mobile App · Wireless Foot Switch · Humminbird® Connectivity · i-Pilot® &
i-Pilot LinkTM Remote

MINN KOTA ACCESSORIES

We offer a wide variety of trolling motor accessories, including:

· 60-Amp Circuit Breaker · Mounting Brackets · Stabilizer Kits · Extension Handles

· Battery Connectors · Battery Boxes · Quick Connect Plugs

minnkotamotors.com
Part #2327130

Minn Kota Consumer & Technical Service Johnson Outdoors Marine Electronics, Inc. PO Box 8129 Mankato, MN 56001
ECN 42102

121 Power Drive Mankato, MN 56001 Phone 800-227-6433 Fax 800-527-4464

©2022 Johnson Outdoors Marine Electronics, Inc. All rights reserved.

Rev K

10/22

TERROVA
MOTEUR DE PÊCHE À LA TRAÎNE MONTÉ SUR L’ÉTRAVE
Manuel du Propriétaire

PRÉSENTATION

MERCI
Nous vous remercions d’avoir choisi Minn Kota. Nous sommes persuadés que vous devriez consacrer plus de temps à pêcher et moins de temps à amarrer votre embarcation. C’est pourquoi nous construisons les propulseurs électriques les plus intelligents, les plus solides et les plus faciles à utiliser. Chaque aspect d’un propulseur électrique Minn Kota est réfléchi et étudié jusqu’à ce qu’il soit digne de porter notre nom. Nous avons investi des heures incalculables de recherche et d’essais pour vous offrir les avantages caractéristiques de Minn Kota, qui vous mène vraiment « n’importe où, et n’importe quand. » Notre principe est simple, nous faisons les choses selon les règles. Nous sommes Minn Kota. Et nous ne cesserons jamais de vous aider à pêcher plus de poissons.

ENREGISTREMENT
N’oubliez pas de conserver votre reçu et d’enregistrer immédiatement votre propulseur électrique. Une fiche d’enregistrement est fournie avec votre moteur; vous pouvez également effectuer l’enregistrement sur notre site Web à minnkotamotors.com/register.
NUMÉRO DE SÉRIE
Le numéro de série à 11 caractères Minn Kota est très important. Cela permet de déterminer le modèle spécifique et l’année de fabrication. Lorsque vous contactez le Service à la clientèle ou que vous enregistrez votre article, vous aurez besoin du numéro de série de votre article. Nous vous suggérons de noter le numéro de série afin qu’il soit disponible à des fins de référence future.
AVIS : Le numéro de série de votre Terrova se trouve sous la barre d’inclinaison.

Made by Minn Kota Johnson Outdoors Marine Electronics, Inc. 121 Power Drive Mankato, MN 56001 USA Trolling Motors Produced in XXXX

PRODUCT DESCRIPTION MODEL XXXXXXX

XXV DC XX A

SER NO YYDDDC00000
EXEMPLE

INFORMATIONS SUR LE MOTEUR (À des fins de Référence par le Client Seulement)
Modèle:


Numéro de Série:


Date de l’achat:_____

Magasin où l’achat a été effectué:


AVIS : Ne retournez pas votre moteur Minn Kota au détaillant. Le détaillant n’est pas autorisé à réparer ou à remplacer cet appareil. Pour le service : communiquer avec Minn Kota au 800-227-6433; retourner le moteur au Centre de service de l’usine de Minn Kota; envoyer ou apporter le moteur à un centre de service agréé de Minn Kota. Une liste de centres de service agréés est disponible sur notre site Web, à minnkotamotors.com. Pour obtenir un service au titre de la garantie, y compris toutes les options susmentionnées, veuillez inclure la preuve d’achat, le numéro de série et la date de l’achat.

64 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

TABLE DES MATIÈRES
FACTEURS DE SÉCURITÉ……………………………………………………………………………………………. 66 GARANTIE ……………………………………………………………………………………………………………. 67 CONNAISSEZ VOTRE BATEAU………………………………………………………………………………………. 68 CARACTÉRISTIQUES ………………………………………………………………………………………………… 69 INSTALLATION……………………………………………………………………………………………………….. 70
Installation du Terrova ……………………………………………………………………………………….. 71 Identification des caractéristiques du moteur de pêche à la traîne au moyen des câbles qui y sont associés …………………………………………………………………………………………… 76 Acheminement des câbles de connexion ………………………………………………………………. 76 Aperçu des caractéristiques et connexion des câbles………………………………………………. 78 INSTALLATION DES BATTERIES ET DU CÂBLAGE …………………………………………………………………. 83 Gréement de l’Embarcation et Installation duProduit ………………………………………………. 83 Tableau des Dimensions de Gabarit des Conducteurs et Disjoncteurs…………………………. 83 Comment Sélectionner une Batterie Adéquate……………………………………………………….. 84 Autres Points à Considérer………………………………………………………………………………….. 84 Comment Raccorder la Batterie…………………………………………………………………………… 85 Connexion des Batteries en Série…………………………………………………………………………. 86 SCHÉMA DE CÂBLAGE DU MOTEUR ……………………………………………………………………………….. 88 UTILISATION ET RÉGLAGE DU MOTEUR …………………………………………………………………………… 90 Caractéristiques du Support ……………………………………………………………………………….. 90 Arrimage et Déploiement du Moteur …………………………………………………………………….. 91 Indicateur d’état de Batterie « Appuyer Pour Tester »………………………………………………. 91 Réglage de la Profondeur du Moteur…………………………………………………………………….. 92 Ajustement de l’Unité Inférieure pour un Arrimage Sûr…………………………………………….. 93 Installation d’un Transducteur Externe………………………………………………………………….. 94 UTILISATION DE LA PÉDALE………………………………………………………………………………………… 95 Contrôle de la Vitesse et de la Direction avec la Pédale…………………………………………….. 95 SERVICE ET ENTRETIEN…………………………………………………………………………………………….. 97 Remplacement de l’Hélice………………………………………………………………………………….. 97 Entretien Général ……………………………………………………………………………………………… 98 Dépannage………………………………………………………………………………………………………. 98 Pour d’autres services de dépannage et de réparation …………………………………………….. 99 DÉCLARATIONS DE CONFORMITÉ ……………………………………………………………………………….. 100 SCHÉMA DES PIÈCES ET LISTE DES PIÈCES …………………………………………………………………….. 102

©2022 Johnson Outdoors Marine Electronics, Inc.

minnkotamotors.com | 65

FACTEURS DE SÉCURITÉ

Veuillez lire attentivement le manuel de l’utilisateur. Suivez toutes les instructions et respectez toutes les consignes de sécurité et mises en garde. L’utilisation de ce moteur n’est autorisée que pour les personnes qui ont lu et compris ces consignes pour l’utilisateur. Les personnes mineures peuvent utiliser ce moteur uniquement sous la supervision d’un adulte.
AVERTISSEMENT
Vous seul êtes responsable de la navigation sécuritaire et prudente sur votre bateau. Nous avons conçu votre Minn Kota pour qu’il soit un outil précis et fiable qui vous permettra d’améliorer l’utilisation de votre bateau et d’accroître votre capacité de pêcher des poissons. Ce produit ne vous exonère pas de la responsabilité de naviguer en toute sécurité avec votre bateau. Vous devez éviter les dangers liés à la navigation et toujours exercer une veille permanente afin de pouvoir réagir au fur et à mesure que les situations se présentent. Vous devez toujours être prêt à reprendre le contrôle manuel de votre bateau. Apprenez à utiliser votre Minn Kota dans une zone exempte de dangers et d’obstacles.
AVERTISSEMENT
Ne faites jamais fonctionner le moteur hors de l’eau, puisque cela entraînerait des blessures causées par l’hélice en rotation. Le moteur doit être débranché de la source d’alimentation lorsqu’il n’est pas utilisé ou lorsqu’il est hors de l’eau. Au moment de brancher les câbles d’alimentation du moteur à la batterie, veiller à ce qu’ils ne soient pas entortillés ou exposés au frottement, puis les placer de telle manière que personne ne risque de trébucher. Avant d’utiliser le moteur, s’assurer que l’isolant des câbles d’alimentation n’est pas endommagé. Ne pas tenir compte de ces mesures de sécurité peut entraîner des courtscircuits avec les batteries et/ou le moteur. Toujours débrancher le moteur des batteries avant le nettoyage ou la vérification de l’hélice. Éviter de submerger complètement le moteur, car l’eau pourrait pénétrer dans l’appareil inférieur par la tête de contrôle et l’arbre. Si le moteur est utilisé alors que de l’eau est présente dans l’appareil inférieur, ce dernier pourrait subir des dommages considérables. Ces dommages ne seront pas couverts par la garantie.
AVERTISSEMENT
Veillez à ce que ni vous ni d’autres personnes ne vous approchiez trop près de l’hélice en rotation, que ce soit seulement avec une partie du corps ou des objets. Le moteur est puissant et pourrait provoquer des situations périlleuses ou des blessures, pour vous ou les autres. Lorsque le moteur est en marche, se méfier des objets flottants ou des personnes qui pourraient être en train de nager. Les personnes, dont les réactions ou la capacité à faire fonctionner le moteur est/sont affaiblie(s) par l’alcool, la drogue, les médicaments ou d’autres substances, ne sont pas autorisées à utiliser ce moteur. Ce moteur n’est pas adapté à l’utilisation dans de forts courants. Le niveau de pression sonore constant du moteur au moment de l’utilisation est inférieur à 70 dB (A). Le niveau de vibration général ne dépasse pas 8,2 pi/s² (2,5 m/s²).
AVERTISSEMENT
Lorsque vous remontez ou abaissez le moteur, gardez vos doigts loin de toutes charnières et tous points de pivot ainsi que de toutes pièces mobiles. En cas d’opération imprévue, retirez les câbles d’alimentation à la batterie.
AVERTISSEMENT
Il est recommandé d’utiliser exclusivement les accessoires approuvés par Johnson Outdoors avec votre moteur Minn Kota. L’utilisation d’accessoires non approuvés, y compris pour monter ou contrôler votre moteur, pourrait causer des dommages, un fonctionnement inattendu du moteur et des blessures. Veillez à utiliser le produit ainsi que les accessoires approuvés, y compris les télécommandes, en toute sécurité et de la manière indiquée pour éviter les accidents ou un fonctionnement inattendu du moteur. Ne retirez pas les pièces installées en usine, y compris les couvercles, boîtiers et protections du moteur et des accessoires.
AVERTISSEMENT
CE PRODUIT CONTIENT UNE PILE BOUTON. Si avalée, une pile bouton au lithium peut causer des blessures graves ou mortelles dans les deux heures. Gardez les piles hors de la portée des enfants. Si vous croyez qu’une pile a été avalée ou placée dans toute partie du corps, consultez un médecin immédiatement.

66 | minnkotamotors.com

©2022 Johnson Outdoors Marine Electronics, Inc.

GARANTIE

GARANTIE SUR LES MOTEURS DE PÊCHE À LA TRAÎNE EN EAU DOUCE MINN KOTA

Moteurs de pêche à la traîne en eau douce Minn Kota – Garantie à vie limitée sur l’arbre composite et garantie limitée de deux ans sur l’ensemble du produit
Johnson Outdoors Marine Electronics, Inc. (« JOME ») offre la garantie limitée suivante uniquement à l’acheteur au détail initial. La garantie n’est pas transférable.

Garantie limitée de deux ans de Minn Kota sur l’ensemble du produit
JOME garantit uniquement à l’acheteur au détail initial que son nouveau propulseur électrique pour eau douce Minn Kota est exempt de défectuosité résultant d’un vice de fabrication et de main-d’oeuvre pouvant survenir au cours des deux (2) ans suivant la date d’achat. JOME se réserve le droit de réparer ou de remplacer, au choix et gratuitement, toute pièce pouvant s’avérer défectueuse pendant la durée de la présente garantie. Cette réparation ou ce remplace-ment est l’unique et exclusive responsabilité de JOME et constitue le seul recours de l’acheteur pour tout manque-ment à la présente garantie.

Garantie à vie limitée Minn Kota sur l’arbre composite
JOME garantit uniquement à l’acheteur au détail initial que l’arbre composite de son propulseur électrique Minn Kota est exempt de défectuosité résultant d’un vice de fabrication et de main-d’oeuvre pouvant survenir au cours de la durée de vie de l’acheteur initial. JOME fournira, gratuitement, un arbre composite neuf pour remplacer tout arbre composite pouvant s’a

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MINN KOTA User Manuals

Related Manuals