Lucci 011520 Porter 1 Light Pendant in White Instruction Manual

Lucci 011520 Porter 1 Light Pendant in White

Product Information:

The Porter Pendant is an indoor lighting product that is available in four different colors – white, blue, mint, and charcoal. It has a rated voltage of 220-240V~ 50Hz and a maximum wattage rating of 45W. The lamp holder used in the product is ES / E27. The weight of the fitting is 1.3kg and the dimensions are H:190mm Dia:175mm Susp:2000mm.

Product Usage:

1. Remove all packaging material from the product and ensure that no accessories are thrown away.
2. Install the mounting bracket onto the ceiling using suitable mounting screws and anchors.
3. Install the two plastic washers in-between the cord and the mounting bracket and cord anchorage. Secure the cord into the mounting bracket by tightening the cord anchorage.
4. Connect the mains supply wire with the fitting wire using the terminal block.
5. Ensure that the wires are secure and no bare wires are exposed. Cover the terminal block with its cover.
6. Slide the canopy along the cord to fully cover the mounting bracket and terminal block. Ensure that the canopy is flush on the ceiling and tighten the canopy cord anchorage to hold it in position.
7. Install a globe into the lamp holder. Do not exceed the maximum wattage rating.
8. After installation, switch on the fitting to test and enjoy your new lighting product.

Safety Tips:

• The Porter Pendant is suitable for indoor use only.
• The mounting point must support 2 times the weight of the fitting.
• The fitting should not be installed in direct line of an air vent/system.
• If installing in an area prone to moisture, ensure that the area is well ventilated and an appropriately rated exhaust fan is used if required.
• Ensure that no parts are missing and the product is not damaged before installation.

In$stallation Requirements:

The installation of the Porter Pendant must comply with the installation requirements specified in eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations. Any damage or corrosion caused by moisture is not a product fault and not covered under warranty. If parts are missing or the product is damaged in any way, return the complete product to the place of purchase for inspection, repair or replacement.

PORTER PENDANT

• SKU# 011520, 011521, 011522, 011523
• Rated Voltage 220-240V~ 50Hz

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.

Warranty

• This light fitting is covered by a 12-month warranty. The warranty is from the date of purchase, not the date of installation.
• If the fitting is not assembled and installed by a licensed electrician the warranty will be void.
• Please retain the proof of purchase and evidence of installation by a licensed electrician.
• The warranty will be void if there is any damage due to improper usage or modification to the fitting.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

• This fitting must be assembled and installed by a licensed electrician.
• All wiring and installation of the light fitting must adhere to local and national wiring rules. eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.
• This is a Class II fitting and this must be maintained during installation and wiring.
• Do not exceed the maximum wattage rating.
• Select a suitable location for installation:
  • This product is suitable for indoor use only.
  • The mounting point must support 2 times the weight of the fitting.
  • Ensure the fitting is not installed in the direct line of an air vent/system.
  • If installing a fitting in an area prone to moisture, ensure that the area is well-ventilated and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
• Take care not to pull any electrical wires during unpacking as this may damage the connection.
• Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
• Check whether the fitting has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.
2. Install the mounting bracket (C) onto the ceiling by using appropriately sized mounting screws (D) and anchors (B). Ensure the screws (D) and anchors (B) used are suitable for the mounting surface and the surrounding environment.
3. Install the two plastic washers (E) in between the cord and the mounting bracket (C) and cord anchorage (F). Secure the cord into the mounting bracket (C) by tightening the cord anchorage (F).
4. Remove the cover from terminal block (A) and connect the main supply wire.
5. Mains Supply Wire Fitting Wire
6. Neutral – Blue or Black Blue or N
7. Live – Brown or Red Brown or L
8. Ensure the wires are secure and no bare wires are exposed. Install the cover back over the terminal block (A).
9. Loosen the canopy cord anchorage (G) and slide the canopy along the cord to fully cover the mounting bracket (C) and terminal block (A).
10. Ensure the canopy (F) is flush on the ceiling and re-tighten the canopy cord anchorage (G) to hold it in position.
11. Install a globe (I – not included) into the lamp holder (H). Do not exceed the maximum wattage rating.
12. After the installation, switch on the fitting to test and enjoy your new lighting product.

Installation Instructions

Safety Tips

• Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the fitting.
• To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power.
• Select a suitable location away from liquids and hazards.
• Ensure that the fitting does not come in contact with corrosive chemicals, etc.
• To clean, wipe with a damp clean cloth. Never soak the fitting with water.

Specifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>