YOLINK YS3606-UC DimmerFob Dimmer Switch User Guide
- June 10, 2024
- YOLINK
Table of Contents
YS3606-UC DimmerFob Dimmer Switch
User Guide DimmerFob
YS3606-UC
Quick Start Guide
Revision Jan. 03, 2023
YS3606-UC DimmerFob Dimmer Switch
Welcome!
Thank you for purchasing YoLink products! We appreciate you trusting YoLink
for your smart home & automation needs.
Your 100% satisfaction is our goal. If you experience any problems with your
installation, with our products or if you have any questions that this manual
does not answer, please contact us right away. See the Contact Us section for
more info.
Thank you!
Eric Vanzo
Customer Experience Manager
User Guide Conventions
The following icons are used in this guide to convey specific types of
information: Very important information (can save you time!)
Before You Begin
Please note: this is a quick start guide, intended to get you started on the
installation of your DimmerFob.
Download the full Installation & User Guide by scanning this QR code:
Installation & User Guide
https://www.yosmart.com/support/YS3606-UC/docs/instruction
You can also find all guides and additional resources, such as videos and
troubleshooting instructions, on the DimmerFob Product Support page by
scanning the QR code below or by visiting: https://shop.yosmart.com/pages
/dimmerfob-product-support
https://shop.yosmart.com/pages/dimmerfob-product-support
Your DimmerFob connects to the internet via a YoLink hub (SpeakerHub or the
original YoLink Hub), and it does not connect directly to your WiFi or local
network. In order for remote access to the device from the app, and for full
functionality, a hub is required. This guide assumes the YoLink app has been
installed on your smartphone, and a YoLink hub is installed and online (or
your location, apartment, condo, etcetera, is already served by a YoLink
wireless network).
In the Box
Get to Know Your DimmerFob
LED & Beep Behaviors
Blinking Red Once, Then Green Once
Device Power Up
Blinking Red And Green Alternately
Restoring to Factory Defaults
Blinking Green Once
One Beep
On or Brightness Increase/ Decrease Button Pressed
Blinking Red Once
Two Beeps
Dimmer Off Button Pressed
Blinking Green Twice
Connecting to Cloud
Quick Blinking Green
Control-D2D Pairing in Progress
Quick Blinking Red
Control-D2D Unpairing in Progress
Slow Blinking Green
Updating
Fast Blinking Red Every 30 Seconds
Batteries are Low, Please Replace the Batteries
Power Up
Press any button on your fob briefly. Observe the LED blinks red then green.
Install the App
If you are new to YoLink, please install the app on your phone or tablet, if
you have not already. Otherwise, please proceed to the next section.
Scan the appropriate QR code below or find the “YoLink app” on the appropriate
app store.
| Apple phone/tablet iOS 9.0 or higher | Android phone/ tablet 4.4 or higher |
|---|---|
| http://apple.co/2Ltturu | http://bit.ly/3bk29mv |
Open the app and tap Sign up for an account. You will be required to provide a
username and a password. Follow the instructions, to set up a new account.
Allow notifications, when prompted.
You will immediately receive a welcome email from no-
reply@yosmart.com with some helpful information.
Please mark the yosmart.com domain as safe, to ensure
you receive important messages in the future.
Log in to the app using your new username and password.
The app opens to the Favorite screen. This is where your favorite devices and
scenes will be shown. You can organize your devices by room, in the Rooms
screen, later.
Refer to the full user guide and online support for instructions on the use of
the YoLink app.
Add the DimmerFob to the App
- Tap Add Device (if shown) or tap the scanner icon:
- Approve access to your phone’s camera, if requested. A viewfinder will be shown on the app.
- Hold the phone over the QR code so that the code appears in the viewfinder. If successful, the Add Device screen will be displayed.
- You can change the device name and assign it to a room later. Tap Bind device.
- If successful, the screen will appear as shown. Tap Done.
Contact Us
We are here for you, if you ever need any assistance installing, setting up or
using a YoLink app or product!
Need help? For fastest service, please email us 24/7 at service@yosmart.com
Or call us at 831-292-4831 (US phone
support hours: Monday – Friday, 9AM to 5PM Pacific)
You can also find additional support and ways to contact us at:
www.yosmart.com/support-and-service
Or scan the QR code: Support Home Page
http://www.yosmart.com/support-and-service
Finally, if you have any feedback or suggestions for us, please email us at
feedback@yosmart.com
Thank you for trusting YoLink!
Eric Vanzo
Customer Experience Manager
15375 Barranca Parkway
Ste. J-107 | Irvine, California 92618
© 2022 YOSMART, INC IRVINE,
CALIFORNIA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>