euro appliances EM90CSX Stainless Steel Cooking Canopy User Guide

euro appliances EM90CSX Stainless Steel Cooking Canopy User Guide

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. ( When the range hood is located above a gas appliance, this distance shall be at least 65 cm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account. The distance of 65 cm can be reduced for:non-combustible parts of range hoods, and parts operating at safety extra low voltage,Provided these parts do not give access to live parts if deformed 😉
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the hood.
• For Class I appliances, check that the domestic power supply guarantees adequateearthing.
• Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm. The route of the flue must be as short as possible.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances),a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Regulations concerning the discharge of air have to be fulfilled

USE

• The cooker hood is only for home use, not suitable for barbecue, roast shop and other commercial purposes.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
• Do not flame under the range hood; risk of fire
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
• Clean and/or replace the Filters after the specified period (Fire hazard).
• Clean the hood using a damp cloth and a neutral liquid detergent.
• The appliance uses 4 hob elements at most.

COMPONENTS

| |
---|---|---
Ref.| Qty.| Product Components
1| 1| Hood Body, complete with: Controls, Light, Blower, Filter.
2.1| 1| Lower Decorative Chimney
2.2| 1| Upper Decorative Chimney ( optional )
3| 1| Flange ( optional )
4| 1| Exhaust Pipe
5| 2| The Activated Charcoal filter ( optional )
Qty.| Documentation
---|---
1| Instruction Manual
Ref.| Qty.| Optional Installation Components
---|---|---
10| 7| Screws 5 x 50
11| 7| Wall Plugs
12| 6| Screws 4,2 x 9,5
20| 1| Hood fixing bracket
21| 1| Chimney fixing bracket ( optional )

DIMENSIONS

INSTALLATION

WALL DRILLING AND BRACKET FIXING

As a first step, proceed with the following drawings:

• A vertical line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted.
• A horizontal line A at 920-1020 mm above the cooker top.
• A horizontal line B at a X mm above the horizontal line A.
• A horizontal line C at a 190mm below the horizontal line A.

Mark Points:

• Mark a point (1) on the horizontal line A, 80 mm to the vertical reference line.
• Repeat this operation on the other side and on the vertical reference line , checking that the three marks are leveled.
• Mark a point (2) on the horizontal line B, 40 mm to the vertical reference line.
• Repeat this operation on the other side , checking that the two marks are leveled.
• Mark a point (3) on the horizontal line C, 170 mm to the vertical reference line.
• Repeat this operation on the other side , checking that the two marks are leveled.

Fix the brackets :

• Drill holes at the marked points with a ɸ10 mm drill bit.
• Insert the Wall Plugs 11 into the holes.
• Fix the hood fixing bracket 20 with 3 screws 10 (5 x 50) at the horizontal line A.
• Fix a Chimney fixing bracket 21 with 2 screws 10 (5 x 50) at the horizontal line B.

Hook the hood body
Hook the hood body to the bracket 20. Level the hood body itself. Remove the filter from the inside of the hood body, fix the screws 10 to Wall Plugs 11 at the points (3).

When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ɸ 150 or ɸ 120 mm, the choice of which is left to the installer.

• If to install a ɸ 120 mm air exhaust connection, insert the reducer flange 3 on the hood body outlet.
• Fix the pipe 4 in position using sufficient pipe clamps (not supplied).
• Remove possible charcoal filters.
  

CHIMNEY ASSEMBLY

Lower Decorative Chimney

• Fix the Lower Decorative Chimney to the hood body with 2 screws 12 (4.2 x 9.5) supplied with the hood.

Upper Decorative Chimney
Fix the upper chimney onto the bracket 21 with 2 screws 12 (4.2 x 9.5) supplied with the hood

Speed adjustment. (For some models)

press again to turn them off.

MAINTENANCE

GREASE FILTERS
CLEANING METAL SELF-SUPPORTING GREASE FILTERS

• The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
• Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling downwards.
• Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make sure that they are completely dry. (The color of the filter surface may change throughout the time but this has no influence to the filter efficiency).
• When fitting the filters into the hood pay attention that they are mounted in correct position , the handle facing outwards.

REPLACING THE ACTIVATED CHARCOAL FILTER

• Remove the metal grease filters
• Remove the saturated activated charcoal filter.
• Fit the new filters.
• Replace the metal grease filters.

LIGHTING

• Replacing the light modules
• Remove the grease filter .
• Disconnect the terminal of LED light.
• Press LED light on the back of the front plate, take the LED light out.
• Replace the lamp(commercially available LED lamp (max.1.5w).

| Max Power| Voltage| Picture| Lamp Cap| ILCOS D code
---|---|---|---|---|---

Square / Diameter: 33.2mm x 120mm

|

1.5W

|

DC 12 V

| |

——

|

DSS-1.5-S-33.2/120

Reinstall LED light module

• Press LED light on the front of front plate, install the LED light on the front plate.
• Connect the terminal of LED light and light leads.
• Reinstall the grease filter.

TROUBLE SHOOTING

Light on, but motor does not work

| The blades are blocked.| Check the blades.
The capacitor is damaged.| Replace capacitor.
The motor is damaged.| Replace motor.
The internal wiring of motor is cut off/ disconnected. An unpleasant smellmay be produced.| Replace motor.
Both light and motor do not work| Apart from the above mentioned, check the following:
Light damaged.| Replace lights.
Power cord loose.| Connect the wires as the electric diagram.
Oil leakage| Outlet and the air ventilation entrance are not tightly sealed.| Take down the outlet and seal with glue.

Vibration

| The blade, if damaged, can cause vibrating.| Replace the blade.
The motor is not tightly fastened.| Fasten the motor tightly.
The cooker hood is not tightly fixed.| Fixed the cooker hood tightly.
Insufficient suction| The distance between the cooker hood and the cooker top is too large.| Readjust the distance.
Too much ventilation from open doors or windows.| Choose a new place to install the appliance or close some doors / windows.
The machine inclines| The fixing screws are not tight enough.| Tighten the fixing screw and make it horizontal.
The hanging screws are not tight enough| Tighten the hanging screw and make it horizontal.

 DISPOSAL OF OLD ELECTRICAL APPLIANCES

The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain,  and reduce the impact on human health and the environment.The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

Pronto Service + Support: 1800 440 335
Email: service@eurostylegroup.com.au
HEAD OFFICE
65 Glynburn Road, Glynde SA 5070
Ph: 08 8165 1012
www.euroappliances.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>