SONOFF ZB-Curtain ZigBee Smart Curtain Motor User Guide
- June 10, 2024
- SonOFF
Table of Contents
SONOFF ZB-Curtain ZigBee Smart Curtain Motor
Please scan the QR code to watch the installation tutorial before installing the device.
- This device does not support the curtain rod and curved curtain track.
- Make sure the top space of the curtain track is greater than 2mm and the track width is less than 40mm so that you can install the C-shape brackets properly.
Install the C-shape brackets
Install the curtain motors
- Remove the cover of the reel, then take out the drive chain.
- Mount the main-motor on the left C-shape bracket and fasten it downwards.
- Hold the vice-motor and press the button on the clamp(R), then gradually extend the drive-chain to the right to the C-shape bracket position.
- The tied part can be disassembled and used if the drive-chain is not long enough.
- Mount the vice-motor on the right C-shape bracket and fasten it downwards.
- Press and hold the button on the clamp(R) while pulling down the chain tightly.
Mount the curtain clamps
Close the curtains before mounting the curtain clamps.
- Double-side opening curtain
- Clip the clamp(R) on the right curtain.
- Clip the clamp(L) on the left curtain, and mount the clamp(L) on the inner curtain drive chain.
- Single-side opening curtain
- Clip the clamp(R) on the opening side of the curtain (The clamp Lis not required).
Pair with eWeLink App
-
Download the eWeLink App
-
Add SONOFF Zigbee Bridge to your eWeLink account
Make sure the proper versions of Zigbee hub: ZBBridge-P V1.1.0 and later, ZBBridge V1.6.0 and later. -
Add curtain motor to Zigbee Bridge
Open the eWeLink App, select the gateway you want to pair and tap the “Add”
icon, then power on the curtain motor. After powering on, LED indicator light
will flash slowly in green, now the device is in pairing mode and waiting for
been added. The LED indicator on the device will keep on for 3s when adding
the device successfully.
The device will exit the pairing mode when it doesn’t be paired successtully within30s. If you want to enter the pairing mode again, press and hold the pairing buttonfor ss until the LED Indicator tlashes slowly in greenand then release.
Effective Communication Distance Verification
Install the device in the desired place, then press the Pairing button on the device. The LED indicator flashes twice means the device and the device under the same Zigbee network (the router device or hub) are in the effective communication distance.
Set up the curtain opening and closing limit position
Please set up the opening limit position first and then set up the closing limit position (Otherwise it will affect the manual pause feature).
- Curtain opening limit position setting: press and hold the “open+Pause” buttons on the remote controller at the same time, and release the buttons when the curtain moves to the desired position that you want to open the curtain.
- Curtain closing limit position setting: press and hold the “Close+Pause” buttons on the remote controller at the same time, and release the buttons when theCurtain moves to the desired position that you want to close the curtain.
If the curtain position changes while the device is powered off, please reset the limit position after the device powers on again.
Charge
- Charged by USB Type-C and proper adapter
- Charged by solar panel
When you using the solar panel to charge the curtain motor, please install the solar panel in a sunny spot.
The adapter and the solar panel are not included in the product, please purchase them separately.
User Manual
https://sonoff.tech/usermanuals
Scan the QR code or visit the website to learn about the detailed user manual and help.
FCC
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type ZBCurtain complies with Directive 2014/53/EU. The full text of
the EU declaration of Conformity is available at the following internet
address:
https://sonoff.tech/usermanuals
Operation frequency Range: 2405-2480MHz(Zigbee)
RF Output Power: 3.68dBm(Zigbee)
Shenzhen Sonoff Technologies Co., Ltd. 3F & 6F, Bldg A, No. 663, Bulong Rd,
Shenzhen, Guangdong, China
ZIP Code :518000 Website: sonoff. te ch MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>