AcuityBrands GlasWerks LED Decorative Outdoor LED Pendants Instruction Manual

LED IMPORTANT SAFETY INSTRUCTIONS
Instruction Manual

GlasWerks LED Decorative Outdoor LED Pendants

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Installation and service of luminaires should be performed by a qualified licensed electrician.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING – RISK OF FIRE OR ELECTRIC SHOCK

• Disconnect or turn off power before installation or servicing.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved recognized wire connectors.
• LUMINAIRES WIRING, POWER SUPPLY OR OTHER ELECTRICAL PARTS MAY BE DAMAGED WHEN INSTALLING RETROFIT HARDWARE. INSPECT WIRING AND COMPONENTS FOR DAMAGE.
• INSTALLATION OF THIS RETROFIT ASSEMBLY REQUIRES A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE LUMINAIRES ELECTRICAL SYSTEM AND THE HAZARD INVOLVED. IF YOU ARE NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED PERSON.

WARNING – RISK OF FIRE OR ELECTRIC SHOCK

•  INSTALL THIS KIT ONLY IN LUMINAIRES THAT HAVE THE CONSTRUCTION FEATURES AND DIMENSION SHOWN IN THE PHOTOGRAPHS AND/OR DRAWINGS AND WHERE THE INPUT RATING OF THE RETROFIT KIT DOES NOT EXCEED THE INPUT RATING OF THE LUMINAIRE.

WARNING RISK OF BURN

• Allow lamp/fixture to cool before handling.
  Do not touch enclosure or light source.

• Do not exceed maximum wattage marked on luminaire label.

• Follow all manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement and recycling.

CAUTION RISK OF FIRE

• ONLY THOSE OPEN HOLES INDICATED IN THE PHOTOGRAPHS AND/OR DRAWINGS MAY BE MADE OR ALTERED AS A RESULT OF KIT INSTALLATION. DO NOT LEAVE ANY OTHER OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS.
• DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.
• WARNING – TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR OTHER SHARP OBJECTS.
• THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINDED BY AUTHORITIES HAVING JURISDICTION.
• INSTALLERS SHOULD NOT DISCONNECT EXISTING WIRES FROM LAMPHOLDER TERMINALS TO MAKE NEW CONNECTIONS AT THE LAMPHOLDER. REMOVE EXISTING LAMPHOLDERS AND LEADS AND MAKE NEW CONNECTIONS USING CONNECTORS SUITABLE FOR THE APPLICATION.

CAUTION
RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.

CAUTION
RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements.
Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com.

Our Brands| Indoor/Outdoor
Lithonia Lighting
Carandini
Holophane
RELOC| Indoor Lighting
Gotham
Mark Architectural Lighting
Peerless
Renaissance Lighting
Winona Lighting| Outdoor Lighting
American Electric Lighting
Antique Street Lamps
Hydrel
Tersen| Controls
DARK TO LIGHT
Lighting Control & Design
ROAM
Sensor Switch
Synergy
---|---|---|---|---

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.
ABL LED General Warnings, Form No. 503.203
© 2011 Acuity Brands Lighting, Inc. All rights reserved. 3/15/11

CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
• Unless individual product specifications deem otherwise: Never connect an LED product directly to dimmer packs, occupancy sensors, timing devices, or other related control devices. LED fixtures must be powered directly off a switched circuit.
• Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling.
• Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature.
• Only use fixture in its intended location.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
• Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.
• Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings.

AFTER INSTALLATION DELIVER THIS MANUAL TO OWNER

GR1970, GR1971, GR1973, GR1498, GR2089

WARNING
Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings.

INTRODUCTION

1.1 Product Description.

• The GlasWerks LED with bowl glass retrofit kit consists of an electrical assembly intended to replace an existing, installed GlasWerks II HID luminaire, see Figure 2.
• Retrofit kit mounts to existing, installed mounting cover (Pendant or Arm Mount), see Figure 1.
• The fixture includes a plug-in electrical module that contains the photocontrol receptacle when specified.

1.2 Alternate Information Sources.
Holophane
Field Service Department
P.O. Box 3004
Newark, OH 43058-3004
866-759-1577

INSTALLATION

2.1 Tools and Material Required.

• No tools required – Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

2.2 Fixture Installation.
2.2.1 Remove existing electrical assembly by unlatching the latch, unplugging terminal block connector and lifting electrical assembly off hinge. See Figure 3.
2.2.2 On new electrical assembly, units supplied with a photocontrol receptacle require a shorting plug or a twist lock photo control to be installed. Install the device by twisting it clockwise, See Figure 4.

CAUTION
A PHOTO CONTROL THAT MEETS THE REQUIREMENTS OF ANSI C136.10 AND WITH A CLEAR WINDOW ON THE SIDE THAT EXPOSES THE PHOTOCELL MUST BE USED.
2.2.3 A new nameplate label is supplied with the retrofit electrical assembly. Place new retrofit label in the general location as shown in Figure 3. Do not remove the old luminaire labels.
2.2.4 Install the retrofit electrical assembly and reconnect terminal block connector. Ensure wires are secured to prevent pinching as assembly is closed. Latch electrical assembly to the mounting cover. See Figure 3.

MAINTENANCE

3.1 Electrical Component Replacement.
3.1.1 Disconnect power to the unit prior to opening and performing any maintenance.
3.1.2 Unlatch Cover from the electrical assembly and let swing down.
3.1.3 Unplug the terminal plug connector, see Figure 4.
3.1.4 Photocontrol Replacement, see Figure 4.
The photocontrol is removed by twisting it counterclockwise. Replace with Holophane approved photocontrol. If no other components are to be replaced go to Section 3.2.9.
3.1.5 Surge Protector Replacement, see Figure 4.
Disconnect surge protector via wiring quick disconnect. Remove screw securing surge protector and retain. Carefully remove the surge protector and install Holophane approved surge protector in the same orientation with original screw.
3.1.6 LED Driver or Dimming Control Replacement, see Figure 4.
Remove electrical module by loosening two retaining screws. Slide electrical module around screw heads using keyholes. Lift electrical module and disconnect optical connector. To replace individual electrical components, tag all leads that will be disconnected and note orientation and position of all components that will be replaced and fasteners holding them. Remove the components to be replaced.
Replace with Holophane supplied electrical components, positioning the new component exactly as the old. Secure with the original hardware and tighten all fasteners securely. Reconnect wiring per earlier applied tags and according industry accepted wiring techniques. Bundle and secure wires as before ensuring no pinched wires.
3.1.7 Electrical Module Replacement, see Figure 4.
Remove electrical module by loosening two retaining screws. Slide electrical module around screw heads using keyholes. Lift electrical module and disconnect optical connector. Replace module with new or electrical module using only Holophane approved components.
Reconnect optical connector then install new electrical module around mounting screws. Tighten screws securely.
3.1.8 Reconnect the electrical assembly connector to the terminal block connector and latch mounting cover to the electrical assembly.
3.1.9 Electrically energize the fixture and check for proper operation.

LIMITED WARRANTY AND LIMITATION OF LIABILITY

The Holophane limited warranty and limitation of liability is published in the “Terms and Conditions” section of the current Holophane buyer’s guide, and is available from your local Holophane sales representative.

|
---|---
|

P10 – AS and AH ONLY

P20 – AS and AH ONLY

P30 – AS and AH ONLY

Field Adjustable Output Module
The Field Adjustable Output (AO) module is an onboard device that adjusts the light output and input wattage to meet site specific requirements, allowing a single fixture configuration to be flexibly applied in many different applications. The AO option is available on the GBLF2RETRO, GPLF2RETRO, GNLF2RETRO, GELF2RETRO and GSLF2RETRO series. The following data is for the AS and AH voltage options.

P40 – AS and AH ONLY

P50 – AS and AH ONLY

Acuity Brands Lighting, Inc.
3825 Columbus Rd SW, Granville, OH 43023
IM-319-A, 9/28/2016 Acuity Brands Lighting Inc.,
All Rights Reserved
Visit our web site atwww.holophane.com
Printed in USA
IM-319-A

Documents / Resources

| AcuityBrands GlasWerks LED Decorative Outdoor LED Pendants [pdf] Instruction Manual
IM-319-A, GlasWerks LED Decorative Outdoor LED Pendants, GlasWerks LED, Decorative Outdoor LED Pendants, Outdoor LED Pendants, LED Pendants, Pendants, Vienna, Prague, Bern, Hallbrook Extended
---|---

References

• Acuity Brands | Lighting, Controls, and Building Management Solutions
• U.S. Environmental Protection Agency | US EPA
• Holophane | Lighting solutions for commercial, industrial, emergency and outdoor applications.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>