DRIVEN 23D24R17 Micro Series Kids Play Truck User Guide
- June 10, 2024
- DRIVEN
Table of Contents
DRIVEN 23D24R17 Micro Series Kids Play Truck User Guide
TO START PLAYING:
- Make sure the ON/OFF switch on the vehicle is in the ON position (Fig. 1).
- Press on the vehicle’s roof, as indicated in (Fig. 2), then press any button on the remote, as indicated in (Fig. 3).
TROUBLESHOOTING:
NOTE: In the event that the controller and/or vehicle are not responsive, press the RESET BUTTON on the back of the remote (Fig. 4) to continue playing. If the controller and/or vehicle still fail to connect, switch the vehicle OFF and back ON again (Fig. 1). Continue with step 2. If the connection issue persists, replace the batteries in the vehicle (Fig. 1) and in the remote (Fig. 4) with new alkaline batteries. Continue with step 1 & 2. NOTE: The vehicle will automatically go into sleep mode after 30 minutes of inactivity to save power. Wake up by pressing on the vehicle’s roof, as indicated in (Fig. 2).
WH1333/WH1333Z
Frequency bands: 2405MHz-2475MHz Maximum radio-frequency power: 5dbm
Use alkaline batteries for longer play time.
WARNING!: SMALL PARTS – CHOKING HAZARD. Not suitable for children under 3 years.
⚠ WARNING: CHOKING HAZARD- Small parts. Not for children under 3 years.
STEERING ALIGNMENT ADJUSTMENT
If the vehicle does not drive in a straight line, adjust the alignment using
the alignment lever. If the vehicle drifts to the left, turn the lever towards
the “R”. If the vehicle drifts to the right, turn the lever towards the “L”.
Please remove all packaging materials before giving to children
User Guide:
- Do not use near seawater or in dirty and dusty environments.
- Do not use in the rain or immediately after rainfall.
- If the vehicle gets wet, open the battery compartment immediately, remove batteries, and turn the vehicle upside down to dry.
- Always clean and dry the vehicle and remote after using outdoors to avoid damage.
- The remote’s control distance may be reduced when using indoors.
- The vehicle’s remote control may not work after long storage. Follow the steps below to re-start: A) Always replace the batteries in the vehicle with 3 new AAA alkaline batteries (Fig. 1). B) Follow steps 1 and 2 on the past page to start playing. C) If the vehicle does not work, put 2 new AAA alkaline batteries in the remote (Fig. 4). D) Follow steps 1 and 2 on the past page to start playing.
BATTERY ADVICE Requires 3 x AAA(1.5V) batteries for the truck (included) Requires 2 x AAA(1.5V) batteries for the remote control (not included) Non- rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the toy before being charged. Rechargeable batteries are only to be charged under adult supervision. Different types of batteries or new and used batteries are not to be mixed. Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity. Exhausted batteries are to be removed from the toy. The supply terminals are not to be short-circuited. ATTENTION: When the module’s functions lose performance, follow instructions carefully to install new batteries.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
(EN): This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence- exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>