ONV-9081R Network Camera
User Manual NETWORK CAMERA
ONV-9081R
ONO-9081R

Network Camera
Copyright
©2021 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the right to change the contents of this document without prior notice.
※ Design and specifications are subject to change without prior notice.
※ The initial administrator ID is “admin” and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent the damage of the information theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

Overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)

7.  Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/
    apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time. ****

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 12 Vdc 1.8 A, or PoE, 0.46 A. (ONV-9081R)

16. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 12 Vdc 1.9 A, or PoE, 0.47 A. (ONO-9081R)

17. This product is intended to be supplied by isolation power.

18. If you use excessive force when installing the product, the camera may be damaged and malfunction. If you forcibly install the product using non-compliant tools, the product may be damaged.

19. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product.

20. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance.
    Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.

21. If you install/disassemble the product in a manner that has not been recommended, the production functions/ performance may not be guaranteed. Install the product by referring to “Installation & connection” in the user manual.

22. Installing or using the product in water can cause serious damage to the product.

23. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the video.

24. This device has been verified using STP cable. The use of appropriate GND grounding and STP cable is recommended to effectively protect your product and property from transient voltage, thunderstroke, communication interruption.

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY  METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.
CAUTION **CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
** The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
** The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Class construction
An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
The battery cannot be replaced.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
CAUTION**
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in
the operating instructions unless you are qualified to do so. Please use the input power with just one camera and other devices must not be connected. When a new product box is opened (or during the initial use of the product), moisture might build up on the glass of the camera. The built-up moisture disappears naturally within a few hours after powered on.
Do not arbitrarily loosen or tighten the gore valve.
The ITE is to be connected only to PoE networks without routing to the outside plant. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3at shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1 or PS2 as defined in UL62368-1.
Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.
Please read the following recommended safety precautions carefully.

• Do not place this apparatus on an uneven surface.
• Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area.
• Do not place this apparatus near conductive material.
• Do not attempt to service this apparatus yourself.
• Do not place a glass of water on the product.
• Do not install near any magnetic sources.
• Do not block any ventilation openings.
• Do not place heavy items on the product.
• Please wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.

• Reference : In case of providing information for helping of product’s usages
• Notice : If there’s any possibility to occur any damages for the goods and human caused by not following the instruction

※ Please read this manual for the safety before using of goods and keep it in the safe place.
We do not guarantee the quality of third-party products (e.g. lenses, accessories) that you separately purchase.
Depending on the app you use, the power consumption might increase.
In particular installation environments, there might be interference in radio communications.
When interference of electromagnetic waves occurs between the product and radio communication device, it is recommended to keep a certain distance between the two or
change the direction of the receiving antenna.
WARNING
To Prevent damage which may caused by IR LED, don’t stare at operating lamp.
For below models only.
ONV-9081R/ONO-9081R
Risk Group 1
WARNING IR emitted from this product.
Do not stare at operating lamp.
Product tested against IEC 62471

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher
• RAM : 8G or higher
• Recommended browser: Chrome
• Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based)
• Supported OS : Windows, Mac, Linux, Android, iOS, Chrome
• Verification environment
  – Windows 10: Google Chrome version 80 or later, Firefox version 72 or later, MS Edge version 83 or later
  – Mac 10.13/14: Safari version 11.0.1 or later

※ The video play performance of the web viewer depends on the performance of the user’s CPU and GPU.
RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

•  Recommended capacity : 16GB to 256GB (MLC type required)
• Recommended Manufacturers : SanDisk, Transcend
• Product Type : High endurance
• The compatibility varies depending on the card manufacturers and types.

NAS RECOMMENDED SPECS

• Recommended capacity : 200GB or higher is recommended.
• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.

Recommended products : QNAP NAS, Synology NAS OPTIONAL ACCESSORIES FOR INSTALLATION
You can purchase appropriate optional accessories available.

SBP-300CMW (Ceiling Mount)
SBP-300WMW (Wall Mount)
SBP-300WMW1 (Wall Mount)
SBP-300NBW (Instalation Box)
SBP-300NBW (Wall Mount Base)
SBP-300PMW (Pole Mount)
SBP-300KMW (Corner Mount)
ONO-9081R| SBP-302PM|

outdoor vandal dome camera

WHAT’S INCLUDED
As for each sales country, accessories are not the same.

AT A GLANCE INSTALLATION

This camera is waterproof and in compliance with the IP67 / IP6K9K spec, but the jack connected to the external cable is not.
You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Precautions before installation
Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera’s weight.
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.
• If the product is installed with excessive force, it may cause damage to the camera due to malfunction. Forcing assembly using non-compliant tools may damage the product.

Removal

1. Peel off the tape that holds the mount plate and remove the mount plate.
2. Take off the lens cover protecting the camera lens.

[Directly installing on wall/ceiling]
1-1. Attach the installation template on the desired surface and drill holes for screws and cables.1-2. Fix the mount plate using appropriate screws.
1-3. Pull out necessary cables among network/power cables through the hole in the mount plate.
[Installing using pipe]
2-1. Attach the installation template and drill holes for screws and cables.2-2. Separate the pipe cover of the mount plate by pressing its sides.2-3. Place the pipe on the mount plate.
2-4. Fix the mount plate using appropriate screws.
2-5. Pull out necessary cables among network/power cables through the pipe. Installation
Use a cable bushing compliant with the network cable to be connected.
– Camera main: use a cable with the diameter of Ø5 to 6.5
– Components: use a cable with the diameter of Ø5 to 8.5
[Installing network/power cables]
1-1. Pull off the extruded parts of the cable bushing to be used.
1-2. Route the network cable through the big hole of the cable bushing and connect to the network cable connector.
1-3. (When using the power) Route the power cable through the small hole of the cable bushing and connect it to the provided terminal block.
1-4. Mount the cable bushing to the camera body. [Installing the network cable] (IP66)
2-1. Pull off the extruded part of the 1-hole cable bushing provided.
2-2. Use the cap installer to pass through the RJ45 cable.2-3. Mount the cable bushing to the camera body. 3. Join the mount plate to the camera body.4. Connect the network/power cables to the port on the camera body.5. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section. (page 21)
6. Assemble the dome cover.
Make sure to firmly tighten the fastening screws so that there is no water damage issue.
Be careful not to alter the monitoring direction of your camera.

Outdoor installation
When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power and network cables.
2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping.
Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.
WHAT’S INCLUDED
As for each sales country, accessories are not the same. AT A GLANCE Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol.
This camera is waterproof and in compliance with the IP67 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Precautions before installation
Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera’s weight.
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site.

And put aside personal belongings from the site, just in case.

• If the product is installed with excessive force, it may cause damage to the camera due to malfunction.

Forcing assembly using non-compliant tools may damage the product.

• Do not use the sunshield hole for any purpose other than for connecting the sunshield.

Installation (Mount plate)
[Directly installing on wall/ceiling]
1-1. Attach the installation template on the desired surface and drill holes for screws and cables.1-2. Fix the Mount plate using appropriate screws.
1-3. Pull out necessary cables among network/power cables through the hole in the Mount plate.
[Installing using pipe]
2-1. Attach the installation template and drill holes for screws and cables.
2-2. Separate the pipe cover of the Mount plate by pressing its sides.
2-3. Place the pipe on the Mount plate.
2-4. Fix the Mount plate using appropriate screws.
2-5. Pull out necessary cables among network/power cables through the pipe.
Installation (Bottom cover)
Use a cable bushing compliant with the network cable to be connected.
– Camera main: use a cable with the diameter of Ø5 to 6.5
– Components: use a cable with the diameter of Ø5 to 8.5
[Installing network/power cables]
1-1. Pull off the extruded parts of the cable bushing to be used.
1-2. Route the network cable through the big hole of the cable bushing and connect to the network cable connector.
1-3. (When using the power) Route the power cable through the small hole of the cable bushing and connect it to the provided terminal block.
1-4. Mount the cable bushing to the Bottom cover.
[Installing the network cable]
2-1. Pull off the extruded part of the 1-hole cable bushing provided.
2-2. Use the cap installer to pass through the RJ45 cable.
2-3. Mount the cable bushing to the Bottom cover.
3. Join the Mount plate with the Bottom cover.

Installing the camera module
1. Hang the safety wire on the hook inside the bottom cover.
2. Connect the network/power cables to the camera module terminal.
3. Attach the camera body to the Bottom cover.
Make sure to firmly tighten the fastening screws so that there is no water damage issue.
4. Adjust the camera direction using the Hex. L wrench provided.
When you adjust the camera position using a bracket, please loosen the bracket screw, adjust the camera, and tighten it. If you attempt to adjust it forcibly while the screw is tight, it may result in a scratch or other problems.
5. Assemble the sunshield to the camera body using sunshield fixing screw.
Outdoor installation
When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.
1. Connect the power and network cables.
2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a dense layer of taping.
Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

Installation & connection

ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA
Adjusting the monitoring direction
You can adjust the camera direction only when the camera is fixed on the ceiling.
At this time, rotating the main body of the camera in the left and right direction is called PAN, and adjusting the angle of the camera is called TILT.
– The pan angle is 0˚ – 360˚.
– The tilt angle is -45˚ – 85˚.
– The rotation angle is 0˚ – 355˚.
  In 75˚ or more tilt angle, a blockage of view or burred image may occur in some part of the screen depending on the zoom magnification.
Do not forcefully rotate or press the focus/zoom lens. Otherwise, the focus might not work properly due to motor failure.
Methods of adjustment

1. Adjust the pan angle taking account of the direction to monitor.
2. Adjust the horizontal angle so that the video does not flip when rotated.
3. Adjust the tilt angle toward the direction to monitor.

Adjust the direction of IR LEDs not to hinder their view by an instrument. CONNECTING WITH OTHER DEVICE The Test Monitor Out port of the product is provided for easier installation, and is not recommended for monitoring purposes.
The Micro USB port of the product is provided for easier installation, and is not recommended for monitoring purposes.

Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Connecting WiFi
Camera Setup

1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port.

Smartphone Setup

1. Install the Wisenet Installation application.

2. Select the camera SSID after turning on the WiFi.

3. Run the Wisenet Installation application.

4. When you log in to the camera, the video will be connected.
   When watching videos using a Wi-Fi dongle, the password is “init123!”.

5. You can adjust angle of view while watching the video through smartphone.

Recommended dongle manufacturer

Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

• If the power sources for PoE+ and DC 12 V are simultaneously turned on, the device power will be supplied by both of PoE+ and DC 12 V.
• You can also use a router featuring PoE+ to supply power to the camera.
• Use PoE+ that is compliant with the IEEE 802.3at protocols.
• If you want to connect an external device, you must turn off the external device before proceeding.
• Connect the set and the adapter power line first, and then connect the power cable to the outlet on the wall.

Power Cable Specification for Each Model

ONV-9081R
ONO-9081R| DC 12V| #20| 7m

18| 11m

16| 17m

Be careful not to reverse the polarity when you connect the power cable.
Network Cable Specification

should be used for the Giga hub.
Max Distance| 100 m| DC Resistance ≤ 0.125 Ω/m
PoE+ Support| IEEE 802.3at|

Network connection and setup

You can set up the network settings according to your network configurations.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING
Connecting to the camera from a local PC in the LAN

1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.

A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator.
By factory default, the IP address will be assigned from the DHCP server automatically.
If there is no DHCP server available, the IP address will be set to 192.168.1.100.

Web viewer

CONNECTING TO THE CAMERA
Normally, you would
By factory default, the IP address will be assigned from the DHCP server automatically.
If there is no DHCP server available, the IP address will be set to 192.168.1.100.
The HTTPS default is 554 or 8554.

1. Launch the Internet browser.
2. Type the IP address of the camera in the address bar. http://192.168.1.100
   – the Login dialog should appear.

If the HTTPS port is other than 554
1. Launch the Internet browser.
2. Type the IP address and HTTPS port number of the camera in the address bar.
→ IP address : 192.168.1.100:HTTPS Port number(8554)
; http://192.168.1.100:8554
– the Login dialog should appear.

PASSWORD SETTING
When you access the product for the first time, you must register the login password.
For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned.
– Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/
For higher security, you are not recommended to repeat the same characters or consecutive keyboard inputs for your passwords.
If you lost your password, you can press the [RESET] button to initialize the product. So, don’t lose your password by using a memo pad or memorizing it.

LOGIN
Whenever you access the camera, the login window appears.
Enter the User ID and password to access the camera.

1. Enter “admin” in the input box.
   The administrator ID, “admin”, is fixed and can not be changed.
   

2. Enter the password in the input field.

3. Click [Sign in].

If you have logged in successfully, you will the Live Viewer screen.
When you access the camera web viewer, pay special attention to the security by checking whether the image data is encrypted.
You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut the image on the borders.

CAMERA WEB VIEWER SETUP

1. Click the [Setup ( ****) icon.
2. The Settings window appears.
3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and system over the network.
4. Click <Help ( )> to view detailed descriptions of each function.

INSTALLING AN APPLICATION

1. To install an application, log in to the web viewer and go to <Setup ( ****) > ; ; <Date & Time> ; and select [Synchronize with NTP server].

2. To register your camera, go to ; and click the [Register] button.

3. In ; , click the [Store] button to go to the app store site.
   If you visited this site for the first time, you need to sign up first to be able to log in.
   

4. Purchase and install the application you want.
   The installed application appears in the “User app” list.
   Please install and run only one application at a time.
   The auto or manual run behaves differently depending on the installed app.

5. If you click the [Open] button of the installed application in ; , the application appears on the screen.
   Various apps can be downloaded from the Store.
   The performance may vary by the features provided by each app. It is recommended to run only one app.
   The auto or manual run behaves differently depending on the installed app.

Appendix

TROUBLESHOOTING

When an Windows 10 user accesses the web viewer through Chrome
or Firefox, the sound volume of microphone changes periodically.| •This is what happens when microphone driver has been set to Realtek driver. Install the High Oefinition Audio device (Windows Default Driver) or the third party driver as the microphone driver.
What are the specifications for WAVE files necessary to play audio at the time of an event?| •Sampling rate of 48,000 KHz a less is recommended.
•For bits per sample (bps), up to 8/16 bit is recommended.
•Only PCM encoding format is supported.
No video is displayed when accessing the plug-In free webviewer on Safari via HTTPS.| •On the authentication popup window prompted when initially accessing https, click “View Authentication Certificate and select the “Always trust when connecting to the designated webviewer r check box.
•If the webviewer continues failing to display a video after you select -Next on the message Window below, press the command key + Q to exit the Safari browser, access again and follow the procedures stated above.
I can’t access the camera from a web browser.| •Check to make sure that the camera’s Network settings are appropriate.
•Check to make sure that all network cables have been connected properly.
•if connected using DHCP, verify that the camera is able to acquire dynamic IP addresses Without any problem.
•If the camera is connected to a Broadband Router, verify that port fonvarang is properly configured.
Viewer got disconnected during monitoring.| •Connected Viewers become disconnected upon any change to camera or network configurations.
•Check all network connections.
Images overlap.| •Check whether two or more cameras are set to a single multicast address instead of different addresses. If a single address is used for multiple cameras, the images may overlap.
No Image appears.| •If the transmission method is set to multicast, check whether there is a router that supports mufticast in the LAN the camera is connected to.