milwaukee FNB16 M12 Fuel 16 Gauge Nibbler User Manual

FNB16 M12 Fuel 16 Gauge Nibbler
User Manual

Cat. No.
M12 FNB16
M12 FUEL™ 16 GAUGE NIBBLER

WARNING
To reduce the risk of injury, the user must read and understand the operator’s manual.

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well-lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock. ‘Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock. ‘When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up, or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
• lf devices are provided for the connection of dust extraction and collection facilities and ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from the frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a  fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  *Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous inthe hands of untrained users.
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
  of the battery pack may create a risk of fire when used with another battery pack.

• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact ac- accidentally occurs, flush with water. I f liquid contacts eyes, additionally seek medical help.

• Liquid ejected from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.

• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to f i r e or temperature above 130°C (265°F) may cause an explosion.

• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

SERVICE

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should o n l y be performed by the manufacturer or authorized service providers.

SPECIFIC SAFETY RULES FOR NIBBLERS

• Always use common sense and be cautious when using tools. It is not possible to anticipate every situation that could resultina a dangerous outcome. Do not use this tool if you do not understand these operating instructions or you feel the work is beyond your capability; contact MILWAUKEE® T o o l or a trained professional for additional information or training.
• Maintain labels and nameplates. This carryimportant information. If unreadable or missing, contact a MILWAUKEE. service facility for a replacement.
  Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain chemicals known to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are: lead from lead-based paint crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber.
  Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work i n a well- ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

ADDITIONAL BATTERY SAFETY RULES

To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack, or charger in fluid or allow fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
Do not charge non-rechargeable batteries.

SYMBOLOGY

| Volts
---|---
| Direct Current
|   No Load Strokes per Minute (SPM)
| Read Operator’s Manual
| Wear eye protection.
| Wear hearing protection.

| Regulatory Compliance Mark (RCM).
This product meets applicable regulatory requirements.
Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

SPECIFICATIONS

Cat. No. ……………………………………….. M12 FNB16
Volts…………………………………………………… 12V DC
Battery Type ………………………………………….M12™
Charger Type…………………………………………M12™
Max. Mild Steel Thickness …………………………16GA
Max. Stainless Steel Thickness ………………….18GA
No Load Strokes
Max. Aluminum Thickness ………………………..12GA
per Minute (SPM) ………………. 1,400 – 2,200 min-1 Recommended Ambient
Operating Temperature ……………….. -17°C to 51°C

FUNCTIONAL DESCRIPTION

ASSEMBLY

Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push the release buttons and pull the battery pack away from the tool.
Always remove the battery pack any time the t o o l is not in use.
To insert the battery, slide the pack into the body of the tool. Make sure it latches securely into place.
Only use accessories specifically recommended for this tool. Others may be hazardous.

Punch and Die Replacement

Replace punch and die at the same time, or as necessary. Use a 2.5 mm open end wrench when replacing punch/dies.

1. Remove the battery pack and place it on a level surface.
2. Remove the die holder.
3. Punch Removal: Loosen the set screw with a 2.5 mm HEX wrench. Remove the punch and set the screw and discard.
4. Punch and Set Screw Installation: Align punch detent with set screw in punch holder. Tighten the set screw securely to below the surface of the punch holder.
5. Die Removal: Remove the two die holder screws and lockwashers with a 2.5 mm HEX wrench. Dis- card two die holder screws and die.
6. Die and Die Holder Screw Installation: Place dies in position. Screw holes in the die and the die holder will align when the die is properly seated. Replace the two die holder screws and lockwashers and tighten them securely.
7. Position the die holder in the desired direction of the cut using locating pin. Replace the collar and tighten it securely.

OPERATION

To reduce the risk of injury, always wear proper eye protection marked to comply with AS/NZS 1337.1.

Fuel Gauge
To determine the amount of charge left in the battery, turn the tool ON. The Fuel Gauge will light up for 2-3 seconds. When less than 10% of charge is left, 1 light on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge will flash 8 times and the tool will not run. Charge the battery pack.
If the battery becomes too hot, the fuel gauge lights will flash and the tool will not run. Allow the battery to cool down.

Speed Dial
MILWAUKEE® Variable Speed Nibblers have a speed dial located on the side of the handle to set the maximum speed. Rotate the speed dial to “5” for maximum speed, and “1”  for minimum speed. “A” for Auto Controlled Start that starts at 1 and ramps up to 5 when the tool detects the user making a cut.

Starting and Stopping

1. To start the tool, grasp the handle(s) firmly and slide the ON/OFF switch forward. NOTE: An LED is turned on when the trigger is pulled and will go off shortly after the trigger is released.
2. To vary the speed, use the speed dial.
3. To stop the tool, slide the ON/OFF switch back. Ensure the tool has come to a complete stop before laying the tool down.

MAINTENANCE

To reduce the risk of injury, always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance. Never disassemble the tool,  battery pack, or charger. Contact a MILWAUKEE® service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack, and charger in good repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise, misalignment or binding of moving parts, breakage of parts, or any other condition that may affect the tool’s operation. Return the tool, battery pack, and charger to a MILWAUKEE® service facility for repair. After six months to one year, depending on use, return the tool, battery pack, and charger to a MILWAUKEE® service facility for inspection.
If the tool does not start or operate at full power with a fully charged battery pack, clean the contacts on the battery pack. If the tool still does not work properly, return the tool,  charger, and battery pack, to a MILWAUKEE® service facility for repairs.

To reduce the risk of personal injury and damage, never immerse your tool, battery pack or charger in liquid or allow a liquid to flow inside them.

Cleaning
Clean dust and debris from any vents. Keep the tool clean, dry, and free of oil or grease. Use only mild soap and a damp cloth to clean, since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia, and household detergents containing ammonia. Never use combustible solvents around tools.

Repairs
For repairs, return the tool, battery pack, and charger to the nearest authorized service center.

ACCESSORIES

Use only recommended accessories. Others may be hazardous.
For a complete listing of accessories, go online to milwaukeetool.com.au/milwaukeetool.co.nz or contact a distributor.

WARRANTY – AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with the tool. This warranty applies only to products sold by authorized dealers in Australia and New Zealand.

SERVICE – AUSTRALIA and NEW ZEALAND
MILWAUKEE® prides itself in producing a premium quality product that is Nothing But Heavy duty.
Your satisfaction with our products is very important to us! If you encounter any problems with the operation of this tool, please contact your authorized MILWAUKEE® dealer.

For a list of MILWAUKEE® dealers, guarantee or service agents please contact MILWAUKEE®
Customer Service or visit our website. (Australia Toll-Free Telephone Number 1300 645 928)
(New Zealand Toll-Free Telephone Number 0800 645 928) or visit milwaukeetool.com.au/milwaukeetool.co.nz.

Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
26 – 40 Nina Link, Dandenong South,
Victoria, 3175, Australia
Milwaukee Tool (New Zealand)
274 Church Street, Penrose,
Auckland, 1061, New Zealand
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP.
PROFESSIONALLY MADE IN VIETNAM
PRINTED IN VIETNAM

References

• Milwaukee Tool | Official New Zealand Site of Milwaukee Tool | Nothing but HEAVY DUTY®
• Milwaukee Tool | Official Australia Site of Milwaukee Tool | Nothing but HEAVY DUTY®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>