DEWALT DWS713 15 Amp 10 in. Electric Single-Bevel Compound Miter Saw Instruction Manual
- June 9, 2024
- Dewalt
Table of Contents
- DEWALT DWS713 15 Amp 10 in. Electric Single-Bevel Compound Miter Saw
- Product Information
- Product Usage Instructions
- Definitions: Safety Alert Symbols and Words
- GENERAL POWER TOOL SAFETY WARNINGS
- Work Area Safety
- Electrical Safety
- Personal Safety
- Power Tool Use and Care
- Service
- Safety Instructions for Miter Saws
- Additional Safety Rules for Miter Saws
- Specifications
- Unpacking Your Saw
- Familiarization (Fig. A, B)
- Bench Mounting (Fig. A)
- Transporting the Saw (Fig. A, C)
- ASSEMBLY AND ADJUSTMENTS
- Changing or Installing a New Saw Blade (Fig. D–F)
- Automatic Electric Brake
- Controls
- OPERATION
- Cutting With Your Saw
- Support for Long Pieces
- Cutting Crown Molding
- Special Cuts
- MAINTENANCE
- Brushes (Fig. Z)
- Cleaning
- Accessories
- Optional Accessories
- Repairs
- Register Online
- Three Year Limited Warranty
- Troubleshooting Guide
- Documents / Resources
DEWALT DWS713 15 Amp 10 in. Electric Single-Bevel Compound Miter Saw
Product Information
The DWS713 is a compound miter saw from DEWALT. It features a 15-amp motor and a stainless steel detent plate with 14 positive stops for improved accuracy. The saw can make miter cuts up to 50 degrees to the left and 60 degrees to the right, as well as bevel cuts up to 48 degrees to the left and 3 degrees to the right. It also has a cam-lock with miter detent override, allowing for quick and accurate angle adjustments. The saw comes with a dust bag to help keep the work area clean.
Product Usage Instructions
Before using the DWS713, read all safety warnings and instructions provided with the saw. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.
- Ensure that the work area is clean and well lit. Do not operate power tools in explosive atmospheres.
- Keep children and bystanders away while operating the saw.
- Ensure that the power tool plug matches the outlet. Do not modify the plug in any way.
- Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators.
- Do not expose the saw to rain or wet conditions.
- Install the blade according to the instructions provided with the saw.
- Adjust the miter and bevel angles to the desired settings using the cam-lock with miter detent override.
- Secure the workpiece with the sliding fence and vertical material clamp.
- Turn on the saw using the trigger switch and make the cut, keeping hands away from the blade.
- After use, turn off the saw and wait for the blade to stop spinning before removing the workpiece.
- Clean the saw and work area after use.
If you have any questions or concerns about the DWS713 or any other DEWALT tool, call their customer service hotline at 1-800-4-DEWALT (1-800-433-9258).
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury. CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in minor or moderate injury.(Used
without word) Indicates a safety related message.
NOTICE
Indicates a practice not related to personal injury which, if not avoided, may
result in property damage.
- Trigger switch
- Operating handle
- Mounting holes
- Lower guard
- Miter lock knob
- Miter detent latch
- Miter scale
- Miter scale screws
- Hand indentations
- Sliding fence
- Bevel lock knob
- Dust port
- Carrying handle
- Fence lock knob
- Clamp mounting holes
- 6 mm hex wrench
- Head lock knob
- Base fence
- Vertical material clamp
- Miter detent override switch
WARNING
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury.
WARNING
To reduce the risk of injury, read the instruction manual.
If you have any questions or comments about this or any DEWALT tool, call us
toll free at:
1-800-4-DEWALT (1-800-433-9258).
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
Work Area Safety
- Keep work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical Safety
-
Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. -
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
-
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
-
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
-
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
-
If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
Personal Safety
-
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
-
Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. -
Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
-
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
-
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
-
If devices are provided for the connection of dust extraction and collection facilities, d ) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
-
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
-
If devices are provided for the connection of dust extraction and collection facilities, h ) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power Tool Use and Care
-
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
-
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
-
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
-
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
-
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
-
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control. -
Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situations.
-
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Service
- Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Safety Instructions for Miter Saws
-
Miter saws are intended to cut wood or wood-like products, they cannot be used with abrasive cut-off wheels for cutting ferrous material such as bars, rods, studs, etc. Abrasive dust causes moving parts such as the lower guard to jam. Sparks from abrasive cutting will burn the lower guard, the kerf insert and other plastic parts.
-
Use clamps to support the workpiece whenever possible. If supporting the workpiece by hand, you must always keep your hand at least 100 mm from either side of the saw blade. Do not use this saw to cut pieces that are too small to be securely clamped or held by hand. If your hand is placed too close to the saw blade, there is an increased risk of injury from blade contact.
-
The workpiece must be stationary and clamped or held against both the fence and the table. Do not feed the workpiece into the blade or cut “freehand” in any way. Unrestrained or moving workpieces could be thrown at high speeds, causing injury.
-
Never cross your hand over the intended line of cutting either in front or behind the saw blade. Supporting the workpiece “cross handed” i.e. holding the workpiece to the right of the saw blade with your left hand or vice versa is very dangerous.
-
Do not reach behind the fence with either hand closer than 100 mm from either side.
-
Do not reach behind the fence with either hand closer than 100 mm from either side of the saw blade, to remove wood scraps, or for any other reason while the blade is spinning. The proximity of the spinning saw blade to your hand may not be obvious and you may be seriously injured.
-
Inspect your workpiece before cutting. If the workpiece is bowed or warped, clamp it with the outside bowed face toward the fence. Always make certain that there is no gap between the workpiece, fence and table along the line of the cut. Bent or warped workpieces can twist or shift and may cause binding on the spinning saw blade while cutting. There should be no nails or foreign objects in the workpiece.
-
Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the workpiece. Small debris or loose pieces of wood or other objects that contact the revolving blade can be thrown with high speed.
-
Cut only one workpiece at a time. Stacked multiple workpieces cannot be adequately clamped or braced and may bind on the blade or shift during cutting.
-
Ensure the miter saw is mounted or placed on a level, firm work surface before use. A level and firm work surface reduces the risk of the miter saw becoming unstable.
-
Plan your work. Every time you change the bevel or miter angle setting, make sure the fence will not interfere with the blade or the guarding system. Without turning the tool “ON” and with no workpiece on the table, move the saw blade through a complete simulated cut to assure there will be no interference or danger of cutting the fence.
-
Provide adequate support such as table extensions, saw horses, etc. for a workpiece that is wider or longer than the table top. Workpieces longer or wider than the miter saw table can tip if not securely supported. If the cut-off piece or workpiece tips, it can lift the lower guard or be thrown by the spinning blade. )
-
Do not use another person as a substitute for a table extension or as additional support. Unstable support for the workpiece can cause the blade to bind or the workpiece to shift during the cutting operation pulling you and the helper into the spinning blade.
-
The cut-off piece must not be jammed or pressed by any means against the
spinning saw blade. If confined, i.e. using length stops, the cut-off piece could get wedged against the blade and thrown violently. -
Always use a clamp or a fixture designed to properly support round material such as rods or tubing. Rods have a tendency to roll while being cut, causing the blade to “bite” and pull the work with your hand into the blade. ) Let the blade reach full speed before contacting the workpiece. This will reduce the risk of the workpiece being thrown.
-
If the workpiece or blade becomes jammed, turn the miter saw off. Wait for all moving parts to stop and disconnect the plug from the power source and/or remove the battery pack. Then work to free the jammed material. Continued sawing with a jammed workpiece could cause loss of control or damage to the miter saw.
-
After finishing the cut, release the switch, hold the saw head down and wait for the blade to stop before removing the cut-off piece. Reaching with your hand near the coasting blade is dangerous.
-
Hold the handle firmly when making an incomplete cut or when releasing the switch before the saw head is completely in the down position. The braking action of the saw may cause the saw head to be suddenly pulled downward, causing a risk of injury.
Additional Safety Rules for Miter Saws
WARNING
Do not allow familiarity (gained from frequent use of your saw) to replace
safety rules. Always remember that a careless fraction of a second is
sufficient to inflict severe injury.
-
DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury.
-
OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety.
-
FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock
or electrocution. Protect electric supply line with at least a 15 ampere time- delay fuse or a circuit breaker. -
MAKE CERTAIN the blade rotates in the correct direction. The teeth on the blade should point in the direction of rotation as marked on the saw.
-
TIGHTEN ALL CLAMP HANDLES, knobs and levers prior to operation. Loose clamps can cause parts or the workpiece to be thrown at high speeds.
-
BE SURE all blade and blade clamps are clean, recessed sides of blade clamps are against blade and arbor screw is tightened securely. Loose or improper blade clamping may result in damage to the saw and possible personal injury.
-
DO NOT OPERATE ON ANYTHING OTHER THAN THE DESIGNATED VOLTAGE for the saw. Overheating, damage to the tool and personal injury may occur.
-
DO NOT WEDGE ANYTHING AGAINST THE FAN to hold the motor shaft. Damage to tool and possible personal injury may occur.
-
NEVER CUT FERROUS METALS or masonry. Either of these can cause the carbide tips to fly off the blade at high speeds causing serious injury.
-
NEVER PLACE HANDS CLOSER THAN 4″ (100 mm) FROM THE BLADE.
-
NEVER HAVE ANY PART OF YOUR BODY IN LINE WITH THE PATH OF THE SAW BLADE. Personal injury will occur.
-
NEVER APPLY BLADE LUBRICANT TO A RUNNING BLADE. Applying lubricant could cause your hand to move into the blade resulting in serious injury.
-
DO NOT place either hand in the blade area when the saw is connected to the power source. Inadvertent blade activation may result in serious injury.
-
NE DO NOT REACH UNDERNEATH THE SAW VER REACH AROUND OR BEHIND THE SAW BLADE. A blade can cause serious injury.
-
DO NOT REACH UNDERNEATH THE SAW unless it is unplugged and turned off. Contact with saw blade may cause personal injury.
-
SECURE THE MACHINE TO A STABLE SUPPORTING SURFACE. Vibration can possibly cause the machine to slide, walk, or tip over, causing serious injury.
-
USE ONLY CROSSCUT SAW BLADES recommended for miter saws. For best results, do not use carbide tipped blades with hook angles in excess of 7 degrees. Do not use blades with deep gullets. These can deflect and contact the guard, and can cause damage to the machine and/or serious injury.
-
USE ONLY BLADES OF THE CORRECT SIZE AND TYPE specified for this tool to prevent damage to the machine and/or serious injury.
-
INSPECT BLADE FOR CRACKS or other damage prior to operation. A cracked or damaged blade can come apart and pieces can be thrown at high speeds, causing serious injury. Replace cracked or damaged blades immediately.
-
CLEAN THE BLADE AND BLADE CLAMPS prior to operation. Cleaning the blade and blade clamps allows you to check for any damage to the blade or blade clamps. A cracked or damaged blade or blade clamp can come apart and pieces can be thrown at high speeds, causing serious injury.
-
DO NOT USE WARPED BLADES. Check to see if the blade runs true and is free from vibration. A vibrating blade can cause damage to the machine and/or serious injury.
-
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic guard. The polycarbonate material used in the guard is subject to attack by certain chemicals.
-
KEEP GUARD IN PLACE and in working order.
-
ALWAYS USE THE KERF PLATE AND REPLACE THIS PLATE WHEN DAMAGED. Small chip accumulation under the saw may interfere with the saw blade or may cause instability of workpiece when cutting.
-
USE ONLY BLADE CLAMPS SPECIFIED FOR THIS TOOL to prevent damage to the machine and/or serious injury.
-
CLEAN THE MOTOR AIR SLOTS of chips and sawdust. Clogged motor air slots can cause the machine to overheat, damaging the machine and possibly causing a short which could cause serious injury.
-
NEVER LOCK THE SWITCH IN THE “ON” POSITION. Severe personal injury may result.
-
NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.
-
ADDITIONAL INFORMATION
regarding the safe and proper operation of power tools (i.e., a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.
WARNING
Cutting plastics, sap coated wood, and other materials may cause melted
material to accumulate on the blade tips and the body of the saw blade,
increasing the risk of blade overheating and binding while cutting.
WARNING
ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also
use face or dust mask if cutting operation is dusty.
ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
-
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
-
ANSI S12.6 (S3.19) hearing protection,
-
NIOSH/OSHA/MSHA respiratory protection.
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: -
lead from lead-based paints,
-
crystalline silica from bricks and cement and other masonry products, and
-
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
-
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
WARNING : Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
WARNING : Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. -
Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in moving parts.
-
An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is, 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
-
When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier the cord.
Volts| Total length of Cord in Feet
(meters)
---|---
120 V| 25 (7.6)| 50 (15.2)| 100 (30.5)| 150 (45.7)
240 V| 50 (15.2)| 100 (30.5)| 200 (61.0)| 300 (91.4)
Ampere Rating| ****
American Wire gauge
More
Than
| not
More Than
0| 6| 18| 16| 16| 14
6| 10| 18| 16| 14| 12
10| 12| 16| 16| 14| 12
12| 16| 14| 12| Not Recommended
The label on your tool may include the following symbols. The symbols and
their definitions are
as follows:
- V…………………….. volts
- Hz…………………… hertz
- min…………………. minutes
- or DC……. direct current
- if………………….. Class I Construction (grounded)
- …/min…………… per minute
- BPM………………… beats per minute
- IPM…………………. impacts per minute
- RPM………………… revolutions per minute
- sfpm……………….. surface feet per minute
- SPM………………… strokes per minute
- A…………………….. amperes
- W……………………. wattor
- AC………… alternating current
- or AC/DC….. alternating or direct current
- ………………….. Class II Construction (double insulated)
- no…………………… no load speed
- n…………………….. rated speed
- ………………….. earthing terminal
- …………………. safety alert symbol
- …………………. visible radiation
- …………………. wear respiratory protection
- …………………. wear eye protection
- …………………. wear hearing protection
- …………………. read all documentation
For your convenience and safety, the following warning labels are on your miter saw.
ON GUARD:
DANGER–KEEP AWAY FROM BLADE.
ON UPPER GUARD:
PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFORE USE
ON TABLE: (2 PLACES)
WARNING
TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL BEFORE
OPERATING MITER SAW. KEEP HANDS AND BODY OUT OF THE PATH OF THE SAW BLADE.
CONTACT WITH BLADE WILL RESULT IN SERIOUS INJURY. DO NOT OPERATE SAW WITHOUT
GUARDS IN PLACE. CHECK LOWER GUARD FOR PROPER CLOSING BEFORE EACH USE. ALWAYS
TIGHTEN ADJUSTMENT KNOBS BEFORE USE. DO NOT PERFORM ANY OPERATION FREEHAND.
CLAMP SMALL PIECES BEFORE CUTTING. NEVER REACH IN BACK OF SAW BLADE. NEVER
CROSS ARMS IN FRONT OF BLADE. TURN OFF TOOL AND WAIT FOR SAW BLADE TO STOP
BEFORE MOVING WORKPIECE, CHANGING SETTINGS OR MOVING HANDS. REMOVE BATTERY
PACK BEFORE ADJUSTING, CHANGING BLADE OR SERVICING. TO REDUCE THE RISK OF
INJURY, RETURN CARRIAGE TO THE FULL REAR POSITION AFTER EACH CROSSCUT
OPERATION. THINK! YOU CAN PREVENT ACCIDENTS.
ON TABLE: (2 PLACES)
Electrical Connection
Be sure your power supply agrees with the nameplate marking. 120 volts, AC
means that your saw will operate on alternating current only. A voltage
decrease of 10 percent or more will cause a loss of power and overheating. All
DEWALT tools are factory tested. If this tool does not operate, check the
power supply.
Specifications
Capacity of cut
- 50° miter left and right
- 48° bevel left: 3° right Baseboard vertically against fence
- Max. Height 4.25″ (108 mm) Max. Width 0.625″ (16 mm)
- 0° miter
- Max. Height 3.5″ (89 mm) Max. Width 6.1″ (155 mm)
- 45° miter
- Max. Height 3.5″ (89 mm)
- Max. Width 4.2″ (107 mm)
- 45° bevel
- Max. Height 2.3″ (58 mm) Max. Width 6.1″ (155 mm) 31.6° miter and 33.9° bevel
- Max. Width 5.25″ (133 mm)
- Result Width 3.5″ (89 mm) Result Height 1.25″ (32 mm)
- Result Width 2.4″ (61 mm) Result Height 1.25″ (32 mm)
- Result Width 3.5″ (89 mm) Result Height .75″ (19 mm)
- Result Height .9″ (23 mm)
Drive
- 120 Volt motor
- 2200 Watts (Max In)
- 15 Amp motor
- 5000 RPM
- Cut helical gears with roller and ball bearings
- Carbide tooth blade
- Automatic electric brake
Unpacking Your Saw
Check the contents of your miter saw carton to make sure that you have received all parts. In addition to this instruction manual, the carton should contain:
- 1 DWS713 miter saw
- 1 DEWALT 10″ (254 mm) dia. saw blade
- 1 6 mm hex wrench
- 1 Dust bag
- 1 Miter lock knob
- 1 Vertical material clamp
- 1 Instruction manual
- COMPONENTS (FIG. A)
WARNING
Never modify the power tool or any part of it. Damage or personal injury could
result. Refer to Figure A at the beginning of this manual for a complete list
of components.
Intended Use
This heavy duty miter saw is designed for professional wood cutting
applications.
DO NOT use under wet conditions or in presence of flammable liquids or gases.
This miter saw is a professional power tool. DO NOT let children come into
contact with the tool. Supervision is required when inexperienced operators
use this tool.
Familiarization (Fig. A, B)
Open the box and lift the saw out by the convenient carrying handle 13 , as shown in Figure B. The miter lock knob 5 is not assembled for shipping. Remove the miter lock knob from the packaging and screw onto the saw. Refer to Figure A for position. Place the saw on a smooth, flat surface such as a workbench or strong table. Examine Figure A to become familiar with the saw and its various parts. The section on adjustments will refer to these terms and you must know what and where the parts are.
CAUTION
Pinch Hazard. To reduce the risk of injury, keep thumb underneath the handle
when pulling the handle down. The lower guard will move up as the handle is
pulled down which could cause pinching. The handle is placed close to the
guard for special cuts. Press down lightly on the operating handle 2 and pull
head lock knob 17 and rotate a quarter turn. Gently release the downward
pressure and allow the arm to rise to its full height. Use the lock down pin
when carrying the saw from one place to another. To lock the arm, rotate head
lock knob a quarter turn and press down on the arm until the arm locks in
place. Always use the carrying handle 13 to transport the saw or the hand
indentations 9 shown in Figure A.
Bench Mounting (Fig. A)
Mounting holes 3 are provided in all four feet to facilitate bench mounting, as shown in Figure A. There are round countersunk holes for use with screws and square holes for use with the miter saw stand “carraige bolt” or M8 (5/16″) or smaller bolts. Use either hole, it is not necessary to use both. Always mount your saw firmly to prevent movement. To enhance the tool’s portability, it can be mounted to a piece of 1/2″ (12.7 mm) or thicker plywood which can then be clamped to your work support or moved to other job sites and reclaimed.
NOTE
If you elect to mount your saw to a piece of plywood, make sure that the
mounting screws don’t protrude from the bottom of the wood. The plywood must
sit flush on the work support. When clamping the saw to any work surface,
clamp only on the clamping bosses where the mounting screw holes are located.
Clamping at any other point will surely interfere with the proper operation of
the saw.
CAUTION
To prevent binding and inaccuracy, be sure the mounting surface is not warped
or otherwise uneven. If the saw rocks on the surface place a thin piece of
material under one saw foot until the saw sits firmly on the mounting surface.
IMPORTANT SAFETY INSTRUCTIONS
Transporting the Saw (Fig. A, C)
WARNING
To reduce the risk of serious personal injury, turn off the tool and
disconnect it from the power source before attempting to move it, change
accessories or make any adjustments.
WARNING
To reduce the risk of serious personal injury, ALWAYS lock the miter lock knob
5 , bevel lock knob 11 , head lock knob, and fence lock knob 14 before
transporting saw.
WARNING
The miter lock knob should be used only when carrying or storing the saw.
NEVER use the lock knob for any cutting operation. In order to conveniently
carry the miter saw from place to place, a carrying handle 13 has been
included on the top of the saw arm and hand indentations 9 in the base, as
shown in Figure A. To transport the saw, lower the arm and rotate the head
lock knob 17 a quarter turn. It will snap into the lock position.
ASSEMBLY AND ADJUSTMENTS
WARNING
To reduce the risk of serious personal injury, turn unit off and
disconnect it from power source before making any adjustments or
removing/installing attachments or accessories. An accidental start-up can
cause injury.
NOTE
Your miter saw is fully and accurately adjusted at the factory at the time of
manufacture. If readjustment due to shipping and handling or any other reason
is required, follow the steps below to adjust your saw. Once made, these
adjustments should remain accurate. Take a little time now to follow these
directions carefully to maintain the accuracy of which your saw is capable.
Changing or Installing a New Saw Blade (Fig. D–F)
WARNING
To reduce the risk of serious personal injury, turn off the tool and
disconnect it from the power source before attempting to move it, change
accessories or make any adjustments.
CAUTION
- Never depress the spindle lock button while the blade is under power or coasting.
- Do not cut ferrous metal (containing iron or steel) or masonry or fiber cement product with this miter saw.
Removing the Blade
- Unplug the saw.
- Raise the arm to the upper position and raise the lower guard 4 as far as possible.
- Loosen, but do not remove guard bracket screw 25 until the bracket can be raised far enough to access the blade screw. Lower guard will remain raised due to the position of the guard bracket screw.
- Depress the spindle lock button 35 while carefully rotating the saw blade by hand until the lock engages.
- Keeping the button depressed, use the other hand and the 6 mm hex wrench 16 provided to loosen the blade screw 21 . (Turn clockwise, left-hand threads.)
- Remove the blade screw 21 , outer blade clamp 22 , and blade 23 . The inner blade clamp 24 may be left on the spindle.
Installing a Blade
-
Unplug the saw.
-
With the arm raised, the lower guard held open and the guard bracket raised, place the blade 23 on the spindle against the inner blade clamp 24 with the teeth at the bottom of the blade pointing toward the back of the saw.
-
Assemble the outer blade clamp 22 onto the spindle.
-
Install the blade screw 21 and, engaging the spindle lock, tighten the screw firmly with the 6 mm hex wrench provided. (Turn counterclockwise, left-hand threads.)
-
Return the guard bracket to its original position and firmly tighten the guard bracket screw 25 to hold bracket in place.
WARNING
- The guard bracket must be returned to its original position and the screw tightened before activating the saw.
- Failure to do so may allow the guard to contact the spinning saw blade resulting in damage to the saw and severe personal injury.
Miter Scale Adjustment (Fig. A, G)
Place a square against the saw’s fence and blade. (Do not touch the tips of the blade teeth with the square. To do so will cause an inaccurate measurement.) Unlock miter lock knob 5 and swing the miter arm until the miter detent locks it at the 0˚ miter position. Do not lock miter lock knob. If the saw blade is not exactly perpendicular to the base fence 18 , loosen the three miter scale screws 8 that hold the miter scale 7 to the base and move the scale/miter arm assembly left or right until the blade is perpendicular to the fence, as measured with the square. Retighten the three screws. Pay no attention to the reading of the miter pointer at this point.
Miter Pointer Adjustment (Fig. A, H)
Unlock miter lock knob 5 and squeeze the miter detent latch 6 to move the miter arm to the zero position. Unlock the miter lock knob to allow the miter detent to snap into place as you rotate the miter arm toward zero. Observe the pointer 37 and miter scale 7 through the viewing opening shown in Figure H. If the pointer does not indicate exactly zero, loosen the pointer screw, adjust the pointer to 0˚ and retighten.
Bevel Square to Table (Fig. I, J)
To align the blade square to the rotary table, lock the arm in the down
position. Place a square against the blade taking care to not have the square
on top of a tooth. Loosen the bevel lock knob 11 so that you can move the
bevel arm. Move the bevel arm as necessary so that the blade is at 0° bevel to
the table. If the bevel arm needs adjustment, locate the right side bevel stop
as shown in Figure J, and adjust the stop screw 26 as necessary.
Bevel Pointer (Fig. J)
If the bevel pointer 27 does not indicate zero, loosen the screw 28 that holds
it in place and move the pointer as necessary.
SUGGESTION: For accuracy, set the top edge so that it aligns with zero.
Bevel Stop (Fig. A, J)
To set the 45° bevel stop, first loosen the left side fence lock knob 14 and
slide the sliding fence 10 as far as it will go to the left. Move the arm to
the left until it stops on the left bevel stop screw 29 . If the bevel pointer
does not indicate exactly 45°, turn the screw downwards. Move the arm to the
left and tighten the bevel clamp knob 11 firmly when the bevel pointer
indicates exactly 45°. Adjust the left side bevel stop screw 29 upwards until
it firmly touches the bevel stop. To achieve 3° right bevel or 48° left bevel,
the stop screws must be adjusted to allow the arm to move to the desired
location. The bevel stops will need readjustment to the zero and 45° positions
after cuts are made.
Fence Adjustment (Fig. K)
WARNING
To reduce the risk of serious personal injury, turn off the tool and
disconnect it from the power source before attempting to move it, change
accessories or make any adjustments. To bevel UP TO 48° left, the sliding
fence can adjust the sliding fence, loosen the fence lock dry run with the saw
turned off and check for to the blade as practical to provide maximum up and
down movement. Tighten the fence complete, don’t forget to relocate the
sliding.
Guard Actuation and Visibility (Fig. L)
CAUTION
Pinch Hazard. To reduce the risk of injury, keep thumb underneath the handle
when pulling the handle down. The lower guard will move up as the handle is
pulled down which could cause pinching. The blade guard on your saw has been
designed to automatically raise when the arm is brought down and to lower over
the blade when the arm is raised. The guard can be raised by hand when
installing or removing saw blades or for inspection of the saw. NEVER RAISE
THE BLADE GUARD MANUALLY UNLESS THE SAW IS TURNED OFF.
NOTE
Certain special cuts will require that you manually raise the guard. Refer
to Cutting Large Material under Special Cuts. The front section of the guard
is louvered for visibility while cutting. Although the louvers dramatically
reduce flying debris, there are openings in the guard and safety glasses
should be worn at all times.
Automatic Electric Brake
Your saw is equipped with an automatic electric blade brake which stops the
saw blade within 5 seconds of trigger release. This is not adjustable.
On occasion, there may be a delay after trigger release to brake engagement.
On rare occasions, the brake may not engage at all and the blade will coast to
a stop. If a delay or “skipping” occurs, turn the saw on and off 4 or 5 times.
If the condition persists, have the tool serviced by an authorized DEWALT
service center. Always be sure the blade has stopped before removing it from
the kerf plate. The brake is not a substitute for guards or for ensuring your
own safety by giving the saw your complete attention.
Controls
Your compound miter saw has several main controls, which will be discussed briefly here. For more information on these controls, see the respective sections later in the manual.
Miter Control (Fig. A)
The miter lock knob 5 and miter detent latch 6 allow you to miter your saw
50° left and right. To miter the saw, unlock miter lock knob 5 by rotating
the knob counter clockwise, squeeze the miter detent latch 6 and set the
miter angle desired on the miter scale. Lock miter lock knob by rotating
clockwise until tight. Override the miter detent latch by unlocking the miter
lock knob and pushing the miter detent override switch 20 downward. To exit
the override, push the miter detent override switch upward.
Bevel Lock (Fig. J)
The bevel lock knob 11 allows you to bevel the saw 48° left and 3° to the
right. To loosen the handle and adjust the bevel setting, turn the handle
counter clock wise, the saw head bevels easily to the left. To tighten, turn
the handle clockwise. Bevel degree markings are on the bottom front of the saw
arm (Fig. J).
Head Down lock Pin (Fig. A)
To lock the saw head in the down position, push the head down, rotate head
lock knob 17 90° and the spring loaded pin will lock in and release the saw
head. This will hold the saw head safely down for moving the saw from place to
place. To release, pull out the head lock knob and rotate 90°.
OPERATION
WARNING
To reduce the risk of serious personal injury, turn unit off and disconnect it
from power source before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
WARNING
Always use eye protection. All users and bystanders must wear eye protection
that conforms to ANSI Z87.1 (CAN/CSA Z94.3). Plug the saw into any household
60 Hz power source. Refer to the nameplate for voltage. Be sure the cord will
not interfere with your work.
Body and Hand Position (Fig. M1–M4)
WARNING
To reduce the risk of serious personal injury, ALWAYS use proper hand
position as shown.
WARNING
To reduce the risk of serious personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper positioning of your body and hands when operating the miter saw will make cutting easier, more accurate and safer. Never place hands near cutting area. Place hands no closer than 4″ (100 mm) from the blade. Hold the workpiece tightly to the table and the fence when cutting. Keep hands in position until the trigger has been released and the blade has completely stopped. ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO THAT YOU CAN CHECK THE PATH OF THE BLADE. DO NOT CROSS ARMS, AS SHOWN IN FIGURE M3. Keep both feet firmly on the floor and maintain proper balance. As you move the miter arm left and right, follow it and stand slightly to the side of the saw blade. Sight through the guard louvers when following a pencil line.
Trigger Switch (Fig. N)
To turn the saw on, push the lock-off lever 30 to the left, then depress the
trigger switch 1 . The saw will run while the switch is depressed. Allow the
blade to spin up to full operating speed before making the cut. To turn the
saw off, release the switch. Allow the blade to stop before raising the saw
head. There is no provision for locking the switch on. A hole 31 is provided
in the trigger for insertion of a padlock to lock the switch off.
Always be sure the blade has stopped before removing it from the kerf.
Dust Extraction (Fig. O)
WARNING
To reduce the risk of serious personal injury, turn unit off and disconnect it
from power source before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury. Your saw
has a built-in dust port 12 that allows either the supplied dust bag 32 or
a shop vacuum system to be connected.
To Attach the Dust Bag
- Fit the dust bag 32 to the dust port 12 as shown in Figure O.
To Empty the Dust Bag
- Remove dust bag 32 from the saw and gently shake or tap the dust bag to empty.
- Reattach the dust bag back onto the dust port 12 .
- You may notice that all the dust will not come free from the bag. This will not affect cutting performance but will reduce the saw’s dust collection efficiency. To restore your saw’s dust collection efficiency, depress the spring inside the dust bag when you are emptying it and tap it on the side of the trash can or dust receptacle.
CAUTION
Never operate this saw unless the dust bag or DEWALT dust extractor is in
place. Wood dust may create a breathing hazard.
Cutting With Your Saw
NOTE
Although this saw will cut wood and many non-ferrous materials, we will limit
our discussion to the cutting of wood only. The same guidelines apply to the
other materials. DO NOT CUT FERROUS (IRON AND STEEL) MATERIALS OR MASONRY WITH
THIS SAW. Do not use any abrasive blades.
Crosscuts
Cutting of multiple pieces is not recommended but can be done safely by
ensuring that each piece is held firmly against the table and fence. A
crosscut is made by cutting wood across the grain at any angle. A straight
crosscut is made with the miter arm at the zero degree position. Set the miter
arm at zero, hold the wood on the table and firmly against the fence. Turn on
the saw by squeezing the trigger switch. When the saw comes up to speed (about
1 second) lower the arm smoothly and slowly to cut through the wood. Let the
blade come to a full stop before raising arm.
CAUTION
Always use a work clamp to maintain control and reduce the risk of
workpiece. damage and personal injury. Miter crosscuts are made with the miter
arm at some angle other than zero. This angle is often 45° for making corners,
but can be set anywhere from zero to 50° left or right. After selecting the
desired miter angle, be sure to tighten the miter lock knob. Make the cut as
described above. To cut through an existing pencil line on a piece of wood,
match the angle as close as possible. Cut the wood a little too long and
measure from the pencil line to the cut edge to determine which direction to
adjust the miter angle and recut. This will take some practice, but it is a
commonly used technique.
Bevel Cuts (Fig. A)
A bevel cut is a crosscut made with the saw blade at a bevel to the wood. In
order to set the bevel, loosen the bevel clamp knob 11 and move the saw to the
left as desired. (It is necessary to move the sliding fence to allow
clearance). Once the desired bevel angle has been set, tighten the bevel clamp
knob firmly. Bevel angles can be set from 3° right to 48° left and can be cut
with the miter arm set between zero and 50° right or left. Ensure the sliding
fence has been adjusted properly. When cutting left bevel, or right miter
compound cuts, it will be necessary to remove the adjustable fence 10 .
Quality of cut
The smoothness of any cut depends on a number of things contributing to the
quality of the cut are: material being cut, blade type, blade sharpness and
rate of cut all contribute to the quality of the cut. When smoothest cuts are
desired for molding and other precision work, a sharp (60–80 tooth carbide)
blade and a slower, even cutting rate will produce the desired results. Ensure
that material does not creep while cutting. Clamp it securely in place. Always
let the blade come to a full stop before raising arm. If small fibers of wood
still split out at the rear of the workpiece, apply a piece of masking tape on
the wood where the cut will be made. Saw through the tape and carefully remove
tape when the cut is finished. For varied cutting applications, refer to the
list of recommended saw blades for your saw and select the one that best fits
your needs. Refer to Saw Blades under Accessories for correct
saw blade.
Clamping the Workpiece (Fig. A)
WARNING
To reduce the risk of serious personal injury, turn off the tool and
disconnect it from the power source before attempting to move it, change
accessories or make any adjustments.
WARNING
A workpiece that is clamped, balanced and secure before a cut may become
unbalanced after a cut is completed. An unbalanced load may tip the saw or
anything the saw is attached to, such as a table or workbench. When making a
cut that may become unbalanced, properly support the workpiece and ensure the
saw is firmly bolted to a stable surface. Personal injury may occur.
WARNING
The clamp foot must remain clamped above the base of the saw whenever the
clamp is used. Always clamp the workpiece to the base of the saw–not to any
other part of the work area. Ensure the clamp foot is not clamped on the edge
of the base of the saw. CAUTION: Always use a work clamp to maintain control
and reduce the risk of workpiece damage and personal injury. If you cannot
secure the workpiece on the table and against the fence by hand, (irregular
shape, etc.) or your hand would be less than 4″ (100 mm) from the blade, a
clamp or other fixture should be used. For best results use the vertical
material clamp 19 provided with your saw. Additional DW7090 clamps can be
purchased at your local retailer or DEWALT service center. Other aids such as
spring clamps, bar clamps or C-clamps may be appropriate for certain sizes and
shapes of material. Use care in selecting and placing these clamps. Take time
to make a dry run before making the cut. The left fence will slide from side
to side to aid in clamping.
To Install Clamp (Fig. A)
- Insert the vertical material clamp 19 into one of the four clamp mounting holes 15 on the base.
- Lifting up on the arm of the clamp can rapidly adjust the height, then use the fine adjust knob to firmly clamp the workpiece.
NOTE
Place the clamp on the opposite side of the base when beveling. ALWAYS MAKE
DRY RUNS (UNPOWERED) BEFORE FINISH CUTS TO CHECK THE PATH OF THE BLADE. ENSURE
THE CLAMP DOES NOT INTERFERE WITH THE ACTION OF THE SAW OR GUARDS.
WARNING
A workpiece that is clamped, balanced and secure before a cut may become
unbalanced after a cut is completed. An unbalanced load may tip the saw or
anything the saw is attached to, such as a table or workbench. When making a
cut that may become unbalanced, properly support the workpiece and ensure the
saw is firmly bolted to a stable surface.
WARNING
The clamp foot must remain clamped above the base of the saw whenever the
clamp is used. Always clamp the workpiece to the base of the saw–not to any
other part of the work area. Ensure the clamp foot is not clamped on the edge
of the base of the saw.
Support for Long Pieces
WARNING
To reduce the risk of serious personal injury, turn off the tool and
disconnect it from the power source before attempting to move it, change
accessories or make any adjustments.
ALWAYS SUPPORT LONG PIECES.
Never use another person as a substitute for a table extension; as additional
support for a workpiece that is longer or wider than the basic miter saw table
or to help feed, support or pull the workpiece. For best results, use the
DWX723, DWX724, DWX725B or DWX726 miter saw stand to extend the table width of
your saw. These are available from your dealer at extra cost. Support long
workpieces using any convenient means such as sawhorses or similar devices to
keep the ends from dropping.
Cutting Picture Frames, Shadow Boxes and Other Four-Sided Projects (Fig.
P)
To best understand how to make the items listed here, we suggest that you try
a few simple projects using scrap wood until you develop a “FEEL” for your
saw. Your saw is the perfect tool for mitering corners like the one shown in
Figure P. Sketch A in Figure P shows a joint made by using the bevel
adjustment to bevel the edges of the two boards at 45° each to produce a 90°
miter corner. For this joint the miter arm was locked in the zero position and
the bevel adjustment was locked at 45°. The wood was positioned with the broad
flat side against the table and the narrow edge against the fence. The cut
could also be made by mitering right and left with the broad surface against
the fence.
Cutting Trim Molding and Other Frames (Fig. P)
Sketch B in Figure P shows a joint made by setting the miter arm at 45° to
miter the two boards to form a 90° corner. To make this type of joint, set the
bevel adjustment to zero and the miter arm to 45°. Once again, position the
wood with the broad flat side on the table and the narrow edge against the
fence. The two sketches in Figure P are for four sided objects only. As the
number of sides changes, so do the miter and bevel angles. The chart below
gives the proper angles for a variety of shapes. The chart assumes that all
sides are of equal length. For a shape that is not shown in the chart, use the
following formula. 180° divided by the number of sides equals the miter or
bevel angle.
EXAMPLES
No. Sides | Angle Miter or Bevel |
---|---|
4 | 45° |
5 | 36° |
6 | 30° |
7 | 25.7° |
8 | 22.5° |
9 | 20° |
10 | 18° |
Cutting Compound Miters (Fig. Q, R)
A compound miter is a cut made using a miter angle and a bevel angle at the
same time. This is the type of cut used to make frames or boxes with slanting
sides like the one shown in Figure Q. NOTE: If the cutting angle varies from
cut to cut, check that the bevel clamp knob and the miter lock knob are
securely tightened. These knobs must be tightened after making any changes in
bevel or miter. The chart (Table 1) will assist you in selecting the proper
bevel and miter settings for common compound miter cuts. To use the chart,
select the desired angle “A” (Figure R) of your project and locate that angle
on the appropriate arc in the chart. From that point follow the chart straight
down to find the correct bevel angle and straight across to find the correct
miter angle. Set your saw to the prescribed angles and make a few trial cuts.
Practice fitting the cut pieces together until you develop a feel for this
procedure and feel comfortable with it.
EXAMPLE
To make a 4 sided box with 26° exterior angles (Angle A, Figure R), use the
upper right arc. Find 26° on the arc scale. Follow the horizontal intersecting
line to either side to get miter angle setting on saw (42°). Likewise, follow
the vertical intersecting line to the top or bottom to get the bevel angle
setting on the saw (18°). Always try cuts on a few scrap pieces of wood to
verify settings on saw.
Miter Scale (Fig. A)
The miter scale 7 is used when calculating angles. To calculate the proper
miter angle, divide 180° by the number of sides of the box or frame. Refer to
Examples.
When Mitering to the Right
To increase the miter angle when mitering to the right, move the arm to align
the appropriate Vernier mark with the closest mark on the miter scale to the
right. To decrease the miter angle when mitering to the right, move the arm to
align the appropriate Vernier mark with the closest mark on the miter scale to
the left.
When Mitering to the Left
To increase the miter angle when mitering to the left, move the arm to align
the appropriate vernier mark with the closest mark on the miter scale to the
left. To decrease the miter angle when mitering to the left, move the arm to
align the appropriate vernier mark with the closest mark on the miter scale to
the right.
Cutting Base Molding
ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE MAKING ANY CUTS.
Straight 90° Cuts (Fig. S)
Position the wood against the fence as shown in Figure S. Turn on the saw,
allow the blade to reach full speed and lower the arm smoothly through the
cut.
Cutting Base Molding up to 3.5″ (88.9 mm) High Vertically Against The Fence
(Fig. L, S)
Position molding as shown in Figure S.
All cuts are made with the back of the molding against the fence and bottom of
the molding against the base.
| inside corner| Outside corner
---|---|---
Left side| 1. Miter left 45°
2. Save left side of cut
| 1. Miter right 45°
2. Save left side of cut
Right side| 1. Miter right 45°
2. Save right side of cut
| 1. Miter left 45°
2. Save right side of cut
Material up to 3.5″ (88.9 mm) can be cut as described above. For wider
boards [up to 4.25″
(107.95 mm)] several minor concessions must be made.
When cutting a board between 3.5″ (88.9 mm) and 4.25″ (107.95 mm) in width the
roller on the tip of the guard could hang up on the workpiece. If this occurs,
simply place your right thumb on the upper side of the guard and roll the
guard up just enough to clear the workpiece, as shown in Figure Once you have
cleared the workpiece, you can release the guard and it will continue to open
as the cut progresses.
When mitering to the right side of a base molding wider than 3.5″ (88.9 mm)
standing vertically against the fence as in Figure S, the saw can only cut
through the board up to 1 inch (25,4 mm) from the end of the board. Trying to
cut more than 1 inch (25,4 mm) will cause the saw’s gear case to interfere
with the workpiece. If you want to cut base molding between 3–1/2″ (88.9 mm)
and 4.25″ (107.95 mm) wide vertically follow the directions below.
Cutting 3.5″–4-1/4″ (88.9 mm–107.95 mm) Base Molding Vertically Against the Fence (Fig. S)
- Position molding as shown in Figure S.
- All cuts made with the back of the molding against the fence
Inside corner Outside corner
Left side
- Position molding with bottom of molding against the base of the saw
- Miter left 45°
- Save left side of cut
- Position molding with bottom of molding against the base of the saw
- Miter right 45°
- Save left side of cut
Right side
- Position molding with bottom of the molding resting on the base of the saw
- Miter right 45°
- Save right side of cut
- Position molding with bottom of the molding against the base of the saw
- Miter left 45°
- Save right side of cut
NOTE
If the cut must be made somewhere other than 1″ (25.4 mm) from the end of the
molding: cut off the molding at 90° approx. 1″ (25.4 mm) longer than your
final length then make the miter cut as described above. Another method of
making the cut is to make a zero degree miter, 45° bevel cut. Your saw can cut
a bevel 6.2″ (157.5 mm) wide.
Cutting Base Molding Laying Flat and Using the Bevel Feature
- All cuts made with the saw set at 45° bevel and 0 miter.
- All cuts made with back of molding laying flat on the saw.
- Move the left side fence out of the path of the blade before attempting any of the following cuts.
Cutting Crown Molding
Your miter saw is better suited to the task of cutting crown molding than any tool made. In order to fit properly, crown molding must be compound mitered with extreme accuracy. The two flat surfaces on a given piece of crown molding are at angles that, when added together, equal exactly 90°. Most, but not all, crown molding has a top rear angle (the section that fits flat against the ceiling) of 52° and a bottom rear angle (the part that fits flat against the wall) of 38°. Your miter saw has special pre-set miter detent points at 31.62° left and right for cutting crown molding at the proper angle. There is also a mark on the Bevel scale at 33.85°. The Bevel Setting/Type of Cut chart gives the proper settings for cutting crown molding. (The numbers for the miter and bevel settings are very precise and are not easy to accurately set on your saw.) Since most rooms do not have angles of precisely 90°, you will have to fine tune your settings anyway.
PRETESTING WITH SCRAP MATERIAL IS EX TREME LY IMPORTANT
For Cutting Crown Molding Laying Flat and Using the Compound Features (Fig. T)
- Move the left side fence 10 out of the path of the blade before attempting any of the following cuts.
- Molding laying with broad back surface down flat on saw table 34 (Fig. T).
- The settings below are for all Standard (U.S.) crown molding with 52° and 38° angles.
| Bevel setting| TYPE OF CUT| Fig. V
---|---|---|---
|
33.9°
| LEFT SIDE, INSIDE CORNER|
1. Top of molding against fence|
2. Miter table set right 31.6°|
3. Save left end of cut |
|
33.9°
| Right SI DE, OUTSIDE CORNER|
1. Bottom of molding against fence|
2. Miter table set left 31.6°| 10
3. Save left end of cut |
|
33.9°
| l EFT siDE, OUTsiDE CORnER|
1. Bottom of molding against fence| 23
2. Miter table set left 31.6°|
__3. Save right end of cut|
|
33.9°
| Right SI DE, OUTSIDE CORNER| RIGHT
1. Top of molding against fence|
2. Miter table set right 31.6°| Fig. W
3. Save right end of cut|
When setting bevel and miter angles for all compound miters, remember that:
The angles presented for crown moldings are very precise and difficult to set
exactly. Since they can easily shift slightly and very few rooms have exactly
square corners, all settings should be tested on scrap molding.
PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT!
Alternative Method for Cutting Crown Molding (Fig. U)
Place the molding on the table at an angle between the fence 10 and the saw
table 34 , as shown in Figure U. Use of the crown molding fence accessory
(DW7084) is highly recommended because of its degree of accuracy and
convenience. The crown molding fence accessory is available at extra cost from
your local dealer. The advantage to cutting crown molding using this method is
that no bevel cut is required. Minute changes in the miter angle can be made
without affecting the bevel angle. This way, when corners other than 90° are
encountered, the saw can be quickly and easily adjusted for them. Use the
crown molding fence accessory (DW7084) to maintain the angle at which the
molding will be on the wall.
Instructions for Cutting Crown Molding Angled Between the Fence and Base of the Saw for All Cuts
- Angle the molding so the bottom of the molding (part which goes against the wall when installed) is against the fence and the top of the molding is resting on the base of the saw, as shown in Figure U.
- The angled “flats” on the back of the molding must rest squarely on the fence and base of the saw.
Inside corner Outside corner
Left side
- Miter right 45°
- Save right side of cut
- Miter left 45°
- Save right side of cu
Right side
- Miter left 45°
- Save left side of cut
- Miter right 45°
- Save left side of cut
Special Cuts
NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST THE FENCE.
Aluminum Cutting (Fig, A, V, W)
ALWAYS USE THE APPROPRIATE SAW BLADE MADE ESPECIALLY FOR CUTTING ALUMINUM.
These are available at your local DE WALT retailer or DeWALT service center.
Certain workpieces, due to their size, shape or surface finish, may require
the use of a clamp or fixture to prevent movement during the cut. Position the
material so that you will be cutting the thinnest cross section, as shown in
Figure V. Figure W illustrates the wrong way to cut these extrusions. Use a
stick wax cutting lubricant when cutting aluminum. Apply the stick wax
directly to the saw blade 23 before cutting. Never apply stick wax to a moving
blade. The wax, available at most hardware stores and industrial mill supply
houses, provides proper lubrication and keeps chips from adhering to the
blade. Be sure to properly secure workpiece. Refer to Saw Blades under
Accessories for correct saw blade.
Bowed Material (Fig. X, Y)
When cutting bowed material always position it as shown in Figure X and never
like that shown in Figure Y. Positioning the material incorrectly will cause
it to pinch the blade near the completion of the cut.
Cutting Plastic Pipe or Other Round Material
Plastic pipe can be easily cut with your saw. It should be cut just like wood and CLAMPED OR HELD FIRMLY TO THE FENCE TO KEEP IT FROM ROLLING. This is extremely important when making angle cuts.
Cutting Large Material (Fig. L)
Occasionally you will encounter a piece of wood a little too large to fit
beneath the lower guard. To clear the guard over the wood, with the motor off
and your right hand on the operating handle, place your right thumb outside of
the upper portion of the guard and roll the guard up just enough to clear the
wood, as shown in Figure L. Release the guard prior to starting the motor The
guard mechanism will function properly during the cut. Only do this when
necessary. NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD OPEN WHEN OPERATING
THIS SAW.
MAINTENANCE
WARNING
To reduce the risk of serious personal injury, turn unit off and disconnect it
from power source before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
WARNING
To reduce the risk of serious personal injury, DO NOT touch the sharp points
on the blade with fingers or hands while performing any maintenance.
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic guard. The polycarbonate material used in the guard is subject to attack by certain chemicals.
- All bearings are sealed. They are lubricated for life and need no further maintenance.
- Periodically clean all dust and wood chips from around AND UNDER the base and the rotary table. Even though slots are provided to allow debris to pass through, some dust will accumulate.
- The brushes are designed to give you several years of use. To replace the brushes refer to Brushes or return the tool to the nearest service center for repair. A list of service center locations is packed with your tool.
Brushes (Fig. Z)
WARNING
To reduce the risk of serious personal injury, turn off the tool and
disconnect it from the power source before attempting to move it, change
accessories or make any adjustments. Inspect carbon brushes regularly by
unplugging the tool, removing the motor end cap 36 by removing the two screws
that secure it, and removing the brush cap that holds the spring-loaded brush
assembly. Keep brushes clean and sliding freely in their guides. Always
replace a used brush in the same orientation in the holder as it was prior to
its removal. If the brush is worn down to approximately 1/2″ (12.7 mm), the
spring will no longer exert pressure and they must be replaced. Use only
identical DEWALT brushes. Use of the correct for proper operation of electric
brake. New brush assemblies are centers. The tool should be allowed to “run
in” (run at no load) Use of the correct grade of brush is essential for proper
operation of electric brake. New brush assemblies are available at DeWALT
service centers. The tool should be allowed to “run in” (run at no load) for
10 minutes before use to seat new brushes. The electric brake may be erratic
in operation until the brushes are properly seated (worn in). Always replace
the brush inspection cap after inspection or servicing the brushes. While
“running in” DO NOT TIE, TAPE, OR OTHERWISE LOCK THE TRIGGER SWITCH ON. HOLD
BY HAND ONLY.
Cleaning
WARNING
Blow dirt and dust out of all air vents with clean, dry air at least once
a week. To minimize the risk of eye injury, always wear ANSI Z87.1 approved
eye protection when performing this procedure.
WARNING
Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and mild soap. Never let any
liquid get inside the tool; never immerse any part of the tool into a liquid.
Accessories
WARNING
Since accessories, other than those offered by DeWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended accessories should be
used with this product. Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized service center.
If you need assistance in locating any accessory, please contact DeWALT
Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-DeWALT (1-800-433-9258) or
visit our website: www.dewalt.com.
Optional Accessories
The following accessories, designed for your saw, may be helpful. Use care in selecting and using accessories.
Clamp: DW7090
Used for firmly clamping workpiece to the saw fence for precision cutting.
Dust Bag: DW7053
Included with some models Equipped with a zipper for easy emptying, the dust
bag will capture the majority of the sawdust produced (not shown).
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Miter Saw Stands
DWX723, DWX724, DWX725B, DWX726 Provides stable and accurate work platform
for miter saws.
Saw Blades
ALWAYS USE 10″ (254 mm) SAW BLADES WITH 5/8″ (16 mm) ARBOR HOLES. SPEED RATING
MUST BE AT LEAST 5500 RPM. Never use a smaller diameter blade. It will not be
guarded properly. Use crosscut blades only! Do not use blades designed for
ripping, combination blades or blades with hook angles in excess of 7 degrees.
BLADE DESCRIPTIONS
APPLICATION| DIAMETER| TEETH
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose| 10″ (254 mm)| 40
Fine Crosscuts| 10″ (254 mm)| 60
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts| 10″ (254 mm)| 80
Non-ferrous metals| 10″ (254 mm)| 80
NOTE: For cutting non-ferrous metals, use only saw blades with TCG teeth
designed for this purpose.
Repairs
WARNING
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when applicable) should be
performed by a DeWALT factory service center or a DeWALT authorized service
center. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
- WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a problem with your product.
- CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof of purchase.
- FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer Safety Act Register online at www.dewalt.com/register.
Three Year Limited Warranty
DeWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DeWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. In addition to the warranty, DeWALT tools are covered by our:
1 YEAR FREE SERVICE
DeWALT will maintain the tool and replace worn parts caused by normal use, for
free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your DeWALT Power
Tool, Laser, or Nailer for any reason, you can return it within 90 days from
the date of purchase with a receipt for a full refund – no questions asked.
LATIN AMERICA
This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in
the packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT
If your warning labels become illegible or are missing, call 1-800-4-DeWALT
(1-800-433-9258) for a free
replacement.
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE!| WHAT’S WRONG?| WHAT TO DO
Saw will not start| Saw not plugged in| Plug in saw.
| Fuse blown or circuit breaker tripped| Replace fuse or reset circuit
breaker.
| Cord damaged| Have cord replaced by authorized service center.
| Brushes worn out| Have brushes replaced by authorized service center or
replace them yourself. Refer to Brushes .
Saw makes unsatisfactory cuts| Dull blade| Replace blade. Refer to
Changing or Installing a New Saw
Blade .
| Blade mounted backwards| Turn blade around. Refer to Changing
or Installing a New Saw Blade .
| Gum or pitch on blade| Remove blade and clean with turpentine and coarse
steel wool or household oven cleaner.
| Incorrect blade for work being done| Change the blade type. Refer to
Saw Blades under Accessories .
Blade does not come up to speed| Extension cord too light or too long| Replace
with adequate size cord. Refer to Additional Saftey Rules
for Miter Saws .
| Low house current| Contact your electric company.
Machine vibrates excessively| Saw not mounted securely to stand or work bench|
Tighten all mounting hardware. Refer to Bench Mounting .
| Stand or bench on uneven floor| Reposition on flat level surface. Refer to
Familiarization .
| Damaged saw blade| Replace blade. Refer to Changing or
Installing a New Saw Blade .
Does not make accurate miter cuts| Miter scale not adjusted correctly| Check
and adjust. Refer to Miter Scale Adjustment under
Assembly and Adjustments .
| Blade is not square to fence| Check and adjust. Refer to Miter
Scale Adjustment under Assembly and Adjustments
.
| Blade is not perpendicular to table| Check and adjust fence. Refer to
Bevel Square to Table under Assembly and
Adjustments .
| Workpiece moving| Clamp workpiece securely to fence or glue 120 grit
sandpaper to fence with rubber cement.
Material pinches blade| Cutting bowed material| Refer to Bowed Material
under Special Cuts .
TABLE 1: COMPOUND MITER CUT
(POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE
AGAINST THE FENCE
SET THIS BEVEL ANGLE ON SAW
Documents / Resources
|
DEWALT DWS713 15 Amp 10 in. Electric Single-Bevel Compound Miter
Saw
[pdf] Instruction Manual
DWS713 15 Amp 10 in. Electric Single-Bevel Compound Miter Saw, DWS713, 15 Amp
10 in. Electric Single-Bevel Compound Miter Saw, Electric Single-Bevel
Compound Miter Saw, Single-Bevel Compound Miter Saw, Bevel Compound Miter Saw,
Compound Miter Saw, Miter Saw, Saw
---|---
References
- DEWALT® Power Tools Official Site | Guaranteed Tough®
- Sign in & Create Account | DEWALT
- Resource for Power Tool Information and Safety Education
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>