Godox ML-150 Macro Ringflash User Manual
- June 9, 2024
- Godox
Table of Contents
Godox ML-150 Macro Ringflash User Manual
Before using the product, make sure to read through this instruction manual. Familiarity with connecting, operating or adjusting procedures will help you obtain the best performance. Keep the manual for future reference.
FOREWORD
Thank you for choosing this GODOX product. GODOX Macro Ring Flash ML-150 is the perfect choice for photographers who require shadow free illumination. It is extremely effective for medical, forensic, scientific, and small commodities photography. Adopting the CPU control circuit, the flash provides high-quality and high-precision, its power output lowest to 1/16.
WARNING!
⚠ Always keep this product from rain or damp in order to prevent fire or
electric shock.
⚠ The flash unit contains high voltage electric parts, do not try to open or
repair the flash unit. If you touch the high-voltage circuit inside this
product, electric shock may occur. Return it back to the nominated repair
service station.
⚠ If the unit is extruded, fallen, suffered from strong impact and thus its
inside is exposed, stop using immediately so as to prevent electric shock
leading from touching the inside electric components. ⚠ Do not fire the flash
direct to the eyes at short distances (especially baby’s eyes), or it may
cause damage to the eyes. When taking flash picture toward baby, it is
recommended to keep the flash unit at least 1 meter (3.3 feet) away from the
subject. Or use diffuser or bounce the light to soften its intensity.
⚠ Always keep the battery or anything easy to be gulped out of children’s
reach. In case of gulping due to carelessness, please contact a doctor
immediately.
⚠ When there is caustic liquid leakage inside, it is necessary to wear gloves
to take out the batter.
⚠ Do not use the flash unit in the flammable gas, chemical or such liquids.
These materials may be sensitive to the flash from the unit in some
circumstance. It may cause fire or electromagnetic interference.
⚠ Do not leave or store the flash unit in temperature over 40 (such like in
the automobile), or it may damage the electronic components. ⚠ The flash unit
isn’t water resistant. Please keep it away from rain or humidity.
⚠ If the flash unit is idle for long, please take out all batteries and keep
the flash unit in dry area.
NOMENCLATURE
- Ring Flash Head
- Locking Ring
- Hot Shoe Stand
- Dedicated Hot Shoe Contact
- Output Level Indicator
- Flash Power Level Button
- Test Button
- Battery Chamber Cover
- Power Switch
- Charging Indicator
- External Power Pack Terminal Cover
- External Power Pack Terminal
- PC Sync Socket Cover
- PC Sync Socket
INSTALLATION
Installing Batteries
NOTE: Take care of the hot battery when changing them after continuous flashes. Take out of the battery when idle in case the battery leakage damages the flash unit.
Mounting Ring Flash on the Camera
- Attach the Control Unit on the Camera
- Attach the Flash Ring on the Camera. 6 types of adapter rings available to suit the camera lens: 49mm, 52mm, 55mm, 58mm, 62mm and 67mm. Choose the adapter ring needed for your camera and attach to the camera lens. Mount the flash ring onto the adapter ring.
USING RING FLASH
Power Management
NOTE: After use, slide the power switch to OFF position.
- Switch to the ON, the flash will start charging (the charging indicator is dim). After several seconds, the charging indicator turns red and the macro ring flash is ready to shoot. For a test flash, press the test button. After use, slide the power switch to OFF position to power off.
- If the red charging indicator lamp flickers in every 1s, it indicates low battery. In such case, the power will turn off automatically and you need to replace the batteries.
Output Control
The flash unit has 5 steps of power output control which indicated by 5 pieces of LED lamp for different level. Press “+” to make power higher and they are 1/16, 1/8, 1/4, 1/2, 1/1, otherwise, press “-” to make power lower.
Synchronization Function
The ring flash and camera will trigger synchronously by using a PC sync cord to connect the sync terminals of the camera and the ring flash together.
Power Saving Function
The flash unit is equipped with power saving mode. When idle for about 30
minutes, it will enter “deeper sleep” state automatically to save power. In
this case, the charging indicator flicks every 3 seconds. To restart the unit,
just press any button.
Protection Function
1. Protection in Continuous Flashes
To prevent the flash head from getting too hot and damage, please do not flash
over 50 times when in power level 1/2, 1/1. Please cool down the flash unit
for at least 10 minutes. The over-temperature protection function will be
activated if you continue to flash after 50 times. In this case, the charging
time will turn to 10-25s. Please cool down the flash unit around 10 minutes
and it will turn to normal state.
Number of flashes that will activate over-temperature protection:
2. Systematic Over-temperature Protection
When the inner circuit is over-heating, which indicates over use of the flash
unit, the inner circuit will shut down power automatically. The flash unit
will turn to normal state after the inner circuit is cooled down (about 10
minutes).
SPECIFICATIONS
Packaging Includes:
Ring Flash…(1)
Instruction Manual…(1)
Adapter Rings49mm,52mm,55mm,58mm,62mm and 67mm
OPTIONAL ACCESSORIES
To provide power supply for Speedlight, shorten the recycle time, up to
300~1000 flashes at full power.
Cx(Canon), Nx(Nikon), Sx(Sony), Mx(Metz)
To connect the speedlite and power pack, dedicated cable available for
different speedlite.
GODOX Photo Equipment Co., Ltd.
1st to 4th Floor, Building 2/ 1st to 4th Floor, Building 4, Yaochuan
Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen
518103, China
Tel: +86-755-29609320(8062)
E-mail: godox@godox.com
705-ML1500-00
Fax: +86-755-25723423
http://www.godox.com
Made In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>