AURA VENOM-D2.1 500 2 Channel Stereo Power Amplifier Owner’s Manual
- June 9, 2024
- Aura
Table of Contents
VENOM-D2.1500
2 CHANNEL STEREO POWER AMPLIFIER
Owner’s Manual
VENOM-D2.1 500 2 Channel Stereo Power Amplifier
WARNING!
PLEASE READ CAREFULLY BEFORE USING
INTRODUCTION
Congratulations and thank you for purchasing AurA VENOM series amplifiers, the logical choice in mobile audio amplification. Your amplifiers have been designed and engineered with the highest quality components and top of the line workmanship to help you reach the superior sound you are after. To achieve optimal performance of your system, please take a few moments to read over this Owner’s manual or visit authorized dealer if needed before starting your installation.
FEATURES
- HIGH SPEED MOSFET POWER SUPPLY
- 12dB/OCT, HIGH PASS FILTER
- 12dB/OCT, LOW PASS FILTER
- BAND-PASS CAPABLE
- SURFACE MOUNT TECHNOLOGY
- DOUBLE SIDED PRINTED CIRCUIT BOARD
- 6dB / 12dB SELECTABLE BASS BOOST
SPECIFICATIONS
| Model | VENOM-D2.1500 |
|---|---|
| RMS power @ 4 ohm | 700 x 2 |
| RMS power @ 2 ohm | 1100 x 2 |
| RMS power @ 1 ohm | 1500 x 2 |
| RMS power @ 4 ohm mono | 2200 x 1 |
| RMS power @ 2 ohm mono | 3000 x 1 |
| Input Sensitivity | 7 V – 0.25 V |
| High Pass Filter | 50 Hz – 800 Hz, 500 Hz – 8 kHz (x10) |
| Low Pass Filter | 20 Hz – 800 Hz, 200 Hz – 8 kHz (x10) |
| Frequency Response | 10 Hz – 34 kHz |
| Signal to Noise Ratio | >90 dB |
| THD @ 4ohm | < 0.15% |
| Working voltage | 9 V – 16 V |
| Fuse Rating | 100A (4 OM), 200A (2 OM), 300A (1 OM), 200A (4 OM bridged), 350A |
(2 OM bridged)
Dimensions| 319 x 210 x 62 mm
All features are subject to change In the continuing effort to improve the products without notice.
POWER CONNECTION
BATT (12V POWER)
Before mounting amplifiers, disconnect the negative cable from the battery to
protect any accidential damage to your amplifiers and audio system. Connect
the power cables to power terminal 12V. All AurA VENOM series amplifiers are
not equipped with fuses so that external fuses should be used. Connect one end
of fuse holder to the power cable going into the amplifiers and the other end
of fuse holder to positive battery. This fuse location will protect the system
and the vehicle against the possibility of a short circuit in the power cable.
Be sure to use fuses and fuse holder adequate for the application.
GND (GROUND)
Locate a secure grounding connection as close to amplifier as possible. Make
sure the location is clean and provides a direct electrical connection to the
frame of the vehicle. The ground needs to have as low of a resistance as
possible. Connect one end of a short piece of the same size cable as the power
cable to the grounding point or to one of your batteries or battery bank. Run
the other end of the ground cable to the mounting location of the amplifiers
for connection to the amplifiers ground terminals and connect the ground cable
to the GND (ground terminal).
REM (REMOTE)
Run a remote turn on cable from the switched 12V source . This may be a toggle
switch, a relay, your source unit’s remote trigger cables, or power antenna
trigger cable. Connect the remote turn on cable to the REM (remote) terminal.
RCA INPURT CONNECTION
SPEAKER CONNECTION
TROUBLE SHOOTING
- AurA VENOM series amplifiers have protection features to prevent any damages from misuse or faulty conditions.
- If VENOM series amplifiers sense excessive heat, short circuited speakers DC, or voltage the protection indicator will light, and the system will be turned off.
- In order to check the problem, you should turn all levels down and all power off and carefully check the installation for wiring mistakes or short.
- If AurA VENOM series amplifiers shuts down due to excessive heat, they will be working later when it is cooled down.
- Before removing your amplfier, refer to the list below and follow the suggested procedures.
NO SOUND (NO OUTPUT)
- Please check all connections, cables routing, short & voltage.
- Please check the fuses. If they are blown, please replace with new one.
- Please check whether speakers work well, you can test speakers by connecting to another amplifier
DISTORTION & NOISE
- Readjust input level and check the speaker quality at another amplifier. Replace poor quality speakers with good quality ones.
- Check amplifiers and headunit’s ground contact. All grounds should be common.
- Check RCA cable, then repalce with new one or reroute RCA cable.
- Engine noise is caused by poor grounding of amplifiers, headunit, other components, battery or alternator, so please check all grounding connection.
POOR BASS RESPONSE
- Please check speaker cables and reverse polarity.
www.aurael.ru
© AURA Electronics lnc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>