SAMSUNG HW-Q930B Soundbar with Wireless Dolby Atmos User Manual

: June 9, 2024
: Samsung

FULL MANUAL
HW-Q930B / HW-Q800B / HW-Q700B
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register your product at
www.samsung.com/register

SAFETY INFORMATION

SAFETY WARNINGS
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Refer to the table below for an explanation of symbols which may be on your Samsung product.

CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.

| This symbol indicates that high voltage is present inside.
It is dangerous to make any kind of contact with any internal part of this product.
---|---
| This symbol indicates that this product has included important literature concerning operation and maintenance.
| Class II product : This symbol indicates that a safety connection to electrical earth (ground) is not required.
If this symbol is not present on a product with a power cord, the product MUST have a reliable connection to
protective earth (ground).
| AC voltage : Rated voltage marked with this symbol is AC voltage.
| DC voltage : Rated voltage marked with this symbol is DC voltage.
| Caution. Consult Instructions for use : This symbol instructs the user to consult the user manual for further safety related information.

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

CAUTION

Do not expose this apparatus to dripping or splashing. Do not put objects filled with liquids, such as vases, on the apparatus.
To turn this apparatus off completely, you must pull the power plug out of the wall socket. Consequently, the power plug must be easily and readily accessible at all times.

CAUTION (for Canada)
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
This device may automatically discontinue transmission if there is no information to transmit, or an operational failure. Note that this is not intended to prohibit the transmission of control or signaling information or the use of repetitive codes where required by the technology.
This Class B digital apparatus complies with Canadian ICES-003.

Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Important Safety Instructions
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

Read these instructions.
Keep these Instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PRECAUTIONS

Ensure that the AC power supply in your house complies with the power requirements listed on the identification sticker located on the bottom of your product. Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4 inches). Make sure the ventilation slots are not covered. Do not place the unit on amplifiers or other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, disconnect the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.
During thunderstorms, disconnect the AC plug from the wall outlet. Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat sources. This could lead to overheating and cause the unit to malfunction.
Protect the product from moisture (i.e. vases), and excess heat (e.g. a fireplace) or equipment creating strong magnetic or electric fields. Unplug the power cable from the AC wall socket if the unit malfunctions. Your product is not intended for industrial use. It is for personal use only. Condensation may occur if your product has been stored in cold temperatures. If transporting the unit during the winter, wait approximately 2 hours until the unit has reached room temperature before using.
The battery used with this product contains chemicals that are harmful to the environment. Do not dispose of the battery in the general household trash. Do not expose the battery to excess heat, direct sunlight, or fire. Do not short circuit, disassemble, or overheat the battery.
CAUTION : Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type.

CHECKING THE COMPONENTS

For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Rear of the Soundbar
Main Unit)
To purchase additional components or optional cables, contact a Samsung Service Center or Samsung Customer Care.
For more information about the wallmount or rubber-foot, see pages 32~34.
Design, specifications, and App screen are subject to change without prior notice.
The appearance of the accessories may differ slightly from the illustrations above.

PRODUCT OVERVIEW

Top Panel of the Soundbar

1| (Multi Function) Button (Q930B / Q800B models)
• In standby mode, press the (Multi Function) button to turn on the Soundbar.
• Press the (Multi Function) button to change the input source.
---|---
1| (Power) Button (Q700B model)
Turns the power on and off.
2| (Volume) Button
Adjusts the volume.
3| (Mic On/Off) Button (Q930B / Q800B models)
Press the button to turn the microphone on or off.
3| (Source) Button (Q700B model)
Press the (Source) button to change the input source.
4| Display
Displays the product’s status and current mode.
D.IN → HDMI → Wi-Fi → BT

When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.
When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.
If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and change the TV speaker to External Speaker.

Bottom Panel of the Soundbar

1| POWER
Connect the Sound bar’s AC power cable. (See page 14)
---|---
2| SERVICE
Connect a USB storage device to upgrade the product’s software.
3| DIGITAL AUDIO IN (OPTICAL)
Connect to the digital (optical) output of an external device. (See page 26)
6| HDMI
Inputs digital video and audio signals simultaneously using an HDMI cable.
Connect to the HDMI output of an external device. (See page 25)
7| HDMI TO TV (ear/ARC)
Connect to the HDMI jack on a TV. (See page 18)

When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable.
Do not connect this unit or other components to an AC outlet until all connections between components are complete.

USING THE SOUNDBAR REMOTE CONTROL

Inserting Batteries before using the Remote Control (AAA batteries X 2)
Slide the back cover in the direction of the arrow until it is completely removed. Insert 2 AAA batteries (1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.

How to Use the Remote Control

1| Power| Turns the Soundbar on and off.
• Auto Power Down Function
The unit turns off automatically in the following situations:
• In D.IN / HDMI / Wi-Fi / BT mode if there is no audio signal for 18 minutes.
---|---|---
2| Source| Press to select a source connected to the Soundbar.
3| Bluetooth PAIR| Switch the Soundbar to Bluetooth pairing mode. Press the button and wait for the “BT PAIRING” screen to connect to a new Bluetooth device.
4| Mute| Press the (Mute) button to mute the sound.
Press it again to unmute the sound.
5| SOUND MODE| By pressing the button, you can select the desired audio mode such as
Surround, Game, Standard, Adaptive sound.
• Standard
Outputs the original sound.
• Surround
Provides a wider sound field than standard.
• Game
Provides stereoscopic sound to immerse you in the action while gaming.
• Adaptive sound
Analyzes the content in real time and automatically provides the optimal sound field based on the characteristics of the content.
6| CH LEVEL| By pressing the button, you can adjust the volume of the each speaker such as Center level, Side level, Wide level, Front Top level, Rear level, and Rear top level.
• To control the volume of the each speaker select Center level, Side level, Wide level, or Front Top level in Sound Settings, and then adjust the volume between -6~+6 by using the Up/Down buttons.
• If Surround Speakers are connected, select Rear level or Rear top level and then use the Up/Down buttons to adjust the volume within a -6 to +6 range.
• CH LEVEL specifications may differ with the respective model.
7| Sound Control| By pressing the button, you can set the audio function such as Space fit sound, AVA, Voice enhance mode, Night mode, Sync, Surround speaker mode, Virtual. The desired item can be adjusted using the Up/Down buttons.
• The Spacefit sound and AVA functions are not supported by Q700B model.
• Voice enhance mode enhances spoken dialog in movies and TV to make it easier to hear.
• Night mode is optimized for night time viewing with the settings adjusted to bring the volume down but keep the dialog clear.
• Press and hold the (Sound Control) button for about 5 seconds to adjust the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the Left/Right buttons and each can be adjusted to a setting between -6 to +6 using the Up/Down buttons. (Make sure the Sound mode is set to “Standard”.)
• If the video on the TV and audio from the Soundbar are not synchronized, select Sync in Sound Control, and then set the audio delay between 0~300 milliseconds by using the Up/Down buttons.
• Sync is only supported for some functions.
• Available Surround speaker mode settings are supported only by Q930B model.
• The Virtual Speaker function can be turned ON/OFF by using the Up/Down buttons.
8| Play / Pause| You can also play or pause music by pressing the button.
9|
Up/Down/Left/
Right| Press the indicated areas to select Up/Down/Left/Right.
Press Up/Down/Left/Right on the button to select or set functions.
• Music Skip
Press the Right button to select the next music file. Press the Left button to select the previous music file.
• ID SET
Use this option when the Subwoofer or Surround Speakers are not connected or need reconnection.
While powered off, press and hold the Up button for 5 seconds to perform ID SET. (See page 16.)
10| Info| Press to display information about the active function or the codec available.
In BT mode, it displays the connected device (when pairing is complete) or “BT ready” (when pairing is required).
11| WOOFER LEVEL|

Push the button up or down to adjust the level of the woofer (bass).

12|
VOLUME| Push the button up or down to adjust the volume.
• Mute
Press the VOL button to mute the sound. Press it again to unmute the sound.
13| TONE CONTROL| By pressing the button, you can adjust the volume of the treble or bass sound. The deferred item can be adjusted using the Up/Down buttons. This function is enabled in Sound mode excluding in Standard mode.
• To control the volume of the treble or bass sound, select TREBLE or BASS in Sound Settings, and then adjust the volume between -6~+6 by using the Up/Down buttons.
• Once the bass level is changed, the woofer level will be also adjusted accordingly.

Active Voice Amplifier (AVA)

Analyzes external noise in real time while soundbar is playing, so that voice audio can always be heard clearly.
No data is saved during the analysis.
This function is not supported by Q700B model.

Using the Hidden Buttons (Buttons with more than one function)

Hidden Button	Reference page
Remote Control Button	Function
WOOFER (Up)	TV remote control On/Off (Standby)
Up	ID SET
C3 (Sound Control)	7 Band EQ

Output specifications for the different sound effect modes
< HW-Q930B>

Effect	Input	Output

< HW-Q800B>

Effect	Input	Output
With Subwoofer Only	With Subwoofer & Surround

Speaker
Standard| 2.0 ch| 2.1 ch| 21 ch
51 ch| 51 ch| 51 ch / 71 ch (DTS)
71 ch| 51 ch| 71 ch
Dolby Atmos(), DTS:X| 51.2 ch| 7.1.4 ch
Surround| 2.0 ch| 51.2 ch| 71.4 ch
51 ch| 51.2 ch| 71.4 ch
7.1 ch| 51.2 ch| 7.1.4 ch
Dolby Atmos0, DTS:X| 51.2 ch| 71.4 ch
Game| 2.0 ch| 51.2 ch| 71.4 ch
51 ch| 51.2 ch| 71.4 ch
71 ch| 51.2 ch| 71.4 ch
Dolby Atmos0, DTS:X| 5.1.2 ch| 7.1.4 ch
Adaptive sound| 2.0 ch| 51.2 ch| 71.4 ch
51 ch| 51.2 ch| 71.4 ch
71 ch| 51.2 ch| 71.4 ch
Dolby AtmosCi, DTS:X| 51.2 ch| 71.4 ch

< HW-Q700B>

Effect	Input	Output
With Subwoofer Only	With Subwoofer & Surround

Speaker
Standard| 2.0 ch| 2.1 ch| 21 ch
51 ch| 3.1 ch| 51 ch
Dolby Atmos®, DTS:X| 3.1.2 ch| 5.1.4 ch
Surround| 2.0 ch| 3.1.2 ch| 5.1.4 ch
51 ch| 3.1.2 ch| 5.1.4 ch
Dolby Atmos®, DTS:X| 3.1.2 ch| 5.1.4 ch
Game| 2.0 ch| 3.1.2 ch| 5.1.4 ch
51 ch| 31.2 ch| 51.4 ch
Dolby Atmos0, DTS:X| 3.1.2 ch| 51.4 ch
Adaptive sound| 2.0 ch| 3.1.2 ch| 51.4 ch
51 ch| 31.2 ch| 51.4 ch
Dolby Atmos®, DTS:X| 31.2 ch| 51.4 ch

The Surround Speakers will not produce sounds for 2 channel output while Standard mode is in use. To enable sound for the Surround Speakers, change the effect mode to Surround.

Adjusting the Soundbar volume with a TV remote control
Adjust the Soundbar volume using the TV’s remote control.

This function can be used with IR remote controls only. Bluetooth remote controls (remote controls that require pairing) are not supported.
Set the TV speaker to External Speaker to use this function.
Manufacturers supporting this function:
Samsung, VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA

Turn Off the Soundbar.
Push up and hold the WOOFER button for 5 seconds.
Each time you push the WOOFER button up and hold it for 5 seconds, the mode switches in the following order: “OFF-TV REMOTE” Default mode), “SAMSUNG-TV REMOTE”, “ALL-TV REMOTE”.

Remote Control Button	Display	Status
(Default mode)
Disable the TV remote control.
	Enable a Samsung TV’s IR remote control.
	Enable a third-party TV’s IR remote control.

CONNECTING THE SOUNDBAR

Connecting the power and units
Use the Power cord to connect the Subwoofer, Surround Speakers, and Soundbar to an electrical outlet in the following order:

For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label: Rear of the Soundbar Main Unit)
1. Connect the Power cord to the Subwoofer.
2. Connect the power cord to the Left and Right Surround Speakers. (optional)
3. Connect the Power cord to the Soundbar.
4. Connect power to the Soundbar, Subwoofer and Surround Speakers. The Subwoofer and Surround Speakers are automatically connected when the Soundbar is turned on.

NOTE

Connect the Subwoofer and Surround Speakers power before connecting to the Soundbar. The Subwoofer and Surround Speakers will be automatically connected when turning on the Soundbar.
If you unplug and reconnect the power cord when the product is turned on, the Soundbar turns on automatically.
The surround speaker system is supported by applicable models only.

Recommended Speaker Layout

CAUTION

Wireless receiving antennas are built into the wireless subwoofer and surround speakers. Keep the units away from water and moisture.
For optimal listening performance, make sure that the areas around the wireless subwoofer and surround speakers locations are clear of any obstructions.

Surround speaker mode (HW-Q930B only)
An optimal surround sound may be delivered depending on the position of the rear speaker. See the illustration below for speaker positioning.
To activate this mode, select the Surround Speaker mode using the remote control of the Soundbar.
( (Sound Control) → Surround speaker → ▲ (Up) /▼ (Down) → Front / Rear)

NOTE

This mode is available only with Soundbar models including a specific surround speaker.
In Front speaker mode, position the front speakers toward you.
The Rear Speaker mode is enabled by default.

Manually connecting the Subwoofer or Surround Speakers
Before performing the manual connection procedure below:

Check whether the power cables for the Soundbar and subwoofer or Surround Speakers are connected properly.
Make sure that the Soundbar is turned off.
1. Turn off the Soundbar main.
2. Press and hold ID SET on the rear of the subwoofer and surround speakers for at least 5 seconds.
The red indicator at the rear of each speaker turns off and the blue indicator blinks.
3. Press the Up button on the remote control for 5 seconds.
The ID SET message appears on the display of the Soundbar for a moment, and then it disappears.
The Soundbar will automatically power on when ID SET is complete.
4. Check if the LINK LED is solid blue (connection complete).
The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the Wireless Subwoofer, surround speakers.

LED Indicator Lights on the Rear of Subwoofer and Surround Speakers

LED	Status	Description
On	Successfully connected
(normal operation)
Blinking	Recovering the connection	Check if the power cable attached to the

main Soundbar unit is connected properly or wait about 5 minutes.
If blinking persists, try manually connecting the
subwoofer and Surround Speakers. See page 16.
| On| Standby (with the
Soundbar main unit turned
off)| Check if the power cable attached to the main Soundbar unit is connected properly.
Connection failed| Connect again. See the instructions for manual
connection on page 16.
| Blinking| Malfunction| See the contact information for the Samsung Service
Center in this manual.

NOTE

If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED on the rear of the sub-woofer will
turn red after blinking in blue several times.
If you use a device that uses the same frequency as the Soundbar near the Soundbar, interference may cause some sound interruption.
The maximum transmission distance of the main unit’s wireless signal is about 32.8 ft (10 m), but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the main unit and the wireless subwoofer, the system may not operate at all because the wireless signal cannot penetrate metal.
The surround speaker system is supported by applicable models only.

CAUTION

Wireless receiving antennas are built into the wireless subwoofer and Surround Speakers. Keep the unit away from water and moisture.
For optimal listening performance, make sure that the area around the wireless subwoofer and the Surround Speakers are clear of any obstructions.

CONNECTING TO A TV

Connecting the TV that supports HDMI ARC (Audio Return Channel)
CAUTION

When both the HDMI cable and optical cable are connected, the HDMI signal is received first.
To connect the HDMI cable between the TV and Soundbar, be sure to connect the terminals marked ARC. Otherwise, the TV sound may not
be output.
The recommended cable is High Speed HDMI Cable with Ethernet.

With the Soundbar and TV turned off, connect the HDMI cable as shown in the figure.
Turn on the Soundbar and TV.
“TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV sound.
• When the TV sound is not output, press the (Multi Function) / (Source) button at the top of the Soundbar or the (Source) button on the remote control to select the “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence, and TV sound is played.
• When connecting a TV that supports the eARC function, “eARC” appears on the display and the sound is heard.
• To connect with eARC, the eARC function in the TV menu should be set to On. Refer to the TV user manual for details on setting. (e.g. Samsung TV : Home ( ) → Menu → Settings ( ) → All Settings ( ) → Sound → Expert Settings → HDMI- eARC Mode (Auto))
• If “TV ARC” does not appear in the display window of the Soundbar main unit, confirm that the HDMI cable is connected to the correct port.
• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.

NOTE

When you connect the TV that supports the HDMI ARC (Audio Return Channel) to the Soundbar with an HDMI cable, you can transmit the
digital video and audio data without connecting a separate optical cable.
We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one whose diameter is less than 0.55 inches (14
mm).
This function is not available if the HDMI cable does not support ARC.
When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on the TV is changed, you will experience better sound quality. (The TV menu may use different words for Dolby Digital and PCM depending on the TV manufacturer.)
The ARC/eARC protocols support Dolby Atmos.
Make sure that the content supports Dolby Atmos®.

Connecting using an Optical Cable
Pre-connection Checklist

When both the HDMI cable and optical cable are connected, the HDMI signal is received first.
When you use an optical cable and the terminals have covers, be sure to remove the covers.

With the TV and Soundbar turned off, connect the DIGITAL AUDIO IN (OPTICAL) port on the Soundbar and the OPTICAL output port on the TV with the optical cable (not supplied), as shown in the figure.
Turn on the Sound bar and TV.
Press the (Multi Function) / (Source) button at the top of the Soundbar or the (Source) button on the remote control to select the “D.IN” mode.
The TV sound is output from the Soundbar.

Connecting via Bluetooth
When a Samsung TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

Only one Samsung TV can be connected at a time.
Samsung TV that supports Bluetooth can be connected. Check the specifications of your TV.

The initial connection

Press the PAIR button on the Soundbar remote control to enter the “BT PAIRING” mode.
(OR) a. Press the (Multi Function) / (Source) button on the top panel and then select “BT”. “BT” changes to “BT PAIRING” in a few seconds automatically or changes to “BT READY” if there is a connect record.
b. When “BT READY” appears, press and hold the (Mic On/Off) / (Source) button on the top panel of the Soundbar for more than 5 seconds to display “BT PAIRING”.
Select Bluetooth mode on the Samsung TV.
(e.g. Home ( ) → Menu → Settings ( ) → All Settings ( ) → Sound → Sound Output → Bluetooth Speaker List → Soundbar Q***B (Bluetooth))
Select “Soundbar Q***B” from the list on TV’s screen.
An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device list. To connect the Samsung TV to the Soundbar, select the message, and then establish a connection.
• When the Samsung TV is connected, [TV Name] → “BT” appears on the Sound bar’s front display.
You can now hear Samsung TV sound from the Soundbar.
• After you have connected the Soundbar to your Samsung TV the first time, use the “BT READY” mode to reconnect.

If the device fails to connect

If you have an existing Soundbar (e.g., Soundbar Q***B) on the list of speakers on the Samsung TV, delete it.
Then repeat steps 1 through 3.

Disconnecting the Soundbar from the Samsung TV
Press the (Multi Function) / (Source) button at the top of the Soundbar or the (Source) button on the remote control to select the mode other than “BT”.

Disconnecting takes time because the Samsung TV must receive a response from the Soundbar. (The time required may differ, depending on the Samsung TV model.)

What is the difference between BT READY and BT PAIRING?

BT READY : In this mode, you can reconnect any Samsung TV or mobile device that was connected before.
BT PAIRING : In this mode, you can connect a new device to the Soundbar.
(Press the PAIR button on the Soundbar remote control or press and hold the (Mic On/Off) / (Source) button on the top of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.)

Notes on Bluetooth connection

Locate a new device within 3.28 ft (1 m) to connect via Bluetooth communication.
If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
The Soundbar automatically turns off after 18 minutes in the Ready state.
The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:
- If there is a strong electrical field around the Soundbar.
- If several Bluetooth devices are simultaneously paired with the Soundbar.
- If the Bluetooth device is turned off, not in place, or malfunctions.
Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit – e.g., microwaves, wireless LAN devices, etc.

Connecting via Wi-Fi
Pre-connection Checklist

Wi-Fi connection is available only on Samsung TV.
Check whether the wireless router (Wi-Fi) is turned on and the TV is connected to the router.
The TV and Soundbar must be connected to the same wireless network (Wi-Fi).
If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi connection between the TV and Soundbar.
Contact your Internet service provider for details.
Because the menus may differ depending on the year of manufacture, refer to your TV manual.
To connect the TV to the Soundbar via Wi-Fi, connect the Soundbar to the wireless router first. See page 29, for details on how to establish a Wi-Fi connection.

For more information about Wi-Fi connection to the Soundbar, see page 29, “Method 2. Connecting via Wi-Fi (Wireless Network)”.
Change the input source of the TV by using the Audio menu to Soundbar.
• Samsung TVs released in 2017 or later
Home ( ) → Menu → Settings ( ) → All Settings ( ) → Sound → Sound Output → Soundbar Q***B (Wi-Fi)

NOTE
The Wi-Fi Dolby Atmos connection is available in some Samsung TVs and some Soundbar models.

Using the Q-Symphony Function
For Q-Symphony, the Soundbar syncs with a Samsung TV to output sound through two devices for optimum surround effect. When the Soundbar is connected, the menu, “TV+Soundbar” appears under the Sound Output menu of the TV. Select the corresponding menu.

• TV menu example: TV + [AV] Soundbar series name (HDMI)

• TV menu example: TV + [AV] Soundbar series name (Wi-Fi)

NOTE

It can operate according to the Codec supported by TV.
This function is supported only when the HDMI Cable or Optical Cable (not supplied) or Wi-Fi is connected.
The message displayed may differ with the TV model.
Ensure that your TV and Soundbar are connected to the same wireless router/frequency.
This function is available in some Samsung TVs and some Soundbar models.

Using the Space fit sound
Provides optimized sound quality by analyzing the listening spaces.

Method 1. Connecting via Soundbar
To enable this function, turn on the Space fit sound mode with the remote control of the Soundbar. ( (Sound Control) → “Spacefit sound Off” → ▲( Up ) → “Spacefit sound On”)
• This is available in all Sound modes.

Method 2. Connecting via TV
To enable this function, turn on the Adaptive Sound+ mode on your Samsung TV menu.
(Home ( ) → Menu → Settings ( ) → All Settings ( ) → General → Intelligent Mode Settings → Adaptive Sound+)
• The sound mode on your Soundbar will automatically change to Adaptive Sound+ if you enable the Adaptive Sound+ mode on your TV.

NOTE
• This function works when the Soundbar connects to some of the Samsung TVs.
• Q700B models support only the method of “Connecting via TV”.

CONNECTING AN EXTERNAL DEVICE

Method 1. Connecting using an HDMI Cable (Capable of Dolby Atmos / DTS:X decoding and playback)
Pre-connection Checklist

If the Audio Output options include Secondary Audio, make sure Secondary Audio is set to Off.
Make sure that the content supports Dolby Atmos® / DTS:X.

Use an HDMI cable to connect the HDMI OUT port on the external device and the HDMI port on the bottom of the Soundbar.
Use an HDMI cable to connect the HDMI IN port of the TV and the HDMI TO TV (eARC/ARC) port on the bottom of the Soundbar.
Turn on the Soundbar, TV, and the external device.
Press the (Multi Function) / (Source) button on the top of the Soundbar or the (Source) button on the remote control to select “HDMI” mode.
The Soundbar display indicates that “HDMI” mode is currently selected and the Soundbar will start playing sounds.

NOTE

When you use Dolby Atmos® / DTS:X: If the input source is Dolby Atmos® / DTS:X, refer to “Output specifications for the different sound effect modes” on page 11.
When Dolby Atmos® is activated, “DOLBY ATMOS” appears in the front display.
When DTS:X is activated, “DTS:X” appear in the front display.
Configuring Dolby Atmos® / DTS:X on your BD player or other device
Open the audio output options on the settings menu of your BD player or other device and make sure that “No Encoding” is selected for Bitstream. For example, on a Samsung BD Player, go to Home Menu → Sound → Digital Output and then select Bitstream (unprocessed).

Supported UHD Signals Specification (3840 x 2160p)

Frame rate (fps)| Color depth| RGB 4:4:4| YCbCr 4:4:4| YCbCr 4:2:2| YCbCr 4:2:0
---|---|---|---|---|---
< 60| 8 bit| 0| 0| 0| 0
10 bit| –| –| 0| 0
12 bit| –| –| 0| 0
120| 8 bit| –| –| –| –
10 bit| –| –| –| –

• Supported specification may vary depending on the connected external device or usage conditions.

Method 2. Connecting using an Optical Cable

Use an optical cable (not supplied) to connect the DIGITAL AUDIO IN (OPTICAL) on the Soundbar main and the OPTICAL OUT port on the external device.
Turn on the Soundbar and external device.
To select “D.IN” mode, press the (Multi Function) / (Source) button on the top of the Soundbar or the (Source) button on the remote control.
Your Soundbar will play sounds from the external device.

CONNECTING A MOBILE DEVICE

Method 1. Connecting via Bluetooth
When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

When you connect a paired Bluetooth device with the Soundbar off, the Soundbar automatically turns on.

The initial connection

When connecting to a new Bluetooth device, make sure the device is within 3.28 ft (1 m) distance.
1. Press the PAIR button on the Soundbar remote control to enter the “BT PAIRING” mode.
(OR)
a. Press the (Multi Function) / (Source) button on the top panel and then select “BT”. “BT” changes to “BT PAIRING” in a few seconds automatically or changes to “BT READY” if there is a connect record.
b. When “BT READY” appears, press and hold the (Mic On/Off) / (Source) button on the top panel of the Soundbar for more than 5 seconds to display “BT PAIRING”.
2. On your device, select “Soundbar Q***B” from the list that appears.
When the Soundbar is connected to the Mobile device, [Mobile Device Name] → “BT” appears in the front display.
3. Play music files from the device connected via Bluetooth through the Soundbar.
After you have connected the Soundbar to your mobile device the first time, use the “BT READY” mode to reconnect.
If the device fails to connect
If you have an existing Soundbar (e.g., “Soundbar Q***B”) in the list of speakers on the Mobile device, delete it.
Repeat steps 1 and 2.

What is the difference between BT READY and BT PAIRING?

BT READY : In this mode, you can reconnect any Samsung TV or mobile device that was connected before.
BT PAIRING : In this mode, you can connect a new device to the Soundbar.
(Press the PAIR button on the Soundbar remote control or press and hold the (Mic On/Off) / (Source) button on the top of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.)

Notes on Bluetooth connection

Locate a new device within 3.28 ft (1 m) to connect via Bluetooth communication.
If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
The Soundbar automatically turns off after 18 minutes in the Ready state.
The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:
- If there is a strong electrical field around the Soundbar.
- If several Bluetooth devices are simultaneously paired with the Soundbar.
- If the Bluetooth device is turned off, not in place, or malfunctions.
Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main unit – e.g., microwaves, wireless LAN devices, etc.
The Soundbar supports SBC data (44.1kHz, 48kHz).
Connect only to a Bluetooth device that supports the A2DP (AV) function.
You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free) function.
When connecting the Soundbar to a Bluetooth device, place them as close to each other as possible.
The farther the Soundbar and Bluetooth device are from each other, the lower the sound quality will become.
The Bluetooth connection may break when the devices are out of the effective range.
The Bluetooth connection may not function as intended in areas with poor reception.
A Bluetooth device may experience noise or malfunction under in the following conditions:
- When the body is in contact with the signal transceiver on the Bluetooth device or Soundbar
- In corners or when there is an obstacle in proximity, such as a wall or partition, where electrical changes may occur.
- When exposed to radio interferences by other products operating on the same frequency ranges, such as medical equipment, microwave
  ovens, and wireless LAN devices.
- Obstacles such as doors and walls may still impact the sound quality even when the devices are within the effective range.
Note that your Soundbar cannot be paired with other Bluetooth devices while using the Bluetooth option.
This wireless device may cause electrical interference during operation.

Disconnecting the Bluetooth device from a Soundbar
You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device’s user manual.

The Soundbar will be disconnected.
When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display “BT DISCONNECTED” on the front display.

Disconnecting the Soundbar from the Bluetooth device
Press the (Multi Function) / (Source) button on the top of the Soundbar or the (Source) button on the remote control to switch the mode from “BT”.

Disconnecting takes time because the Bluetooth device must receive a response from the Soundbar. (Disconnection time may differ, depending on the Bluetooth device)
When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display “BT DISCONNECTED” on the front display.

Method 2. Connecting via Wi-Fi (Wireless Network)
To connect a Soundbar to a mobile device via a wireless network (Wi-Fi), the SmartThings app is required.

The initial connection

Install and launch the SmartThings app from your mobile device (smartphone or tablet).
On the app, follow the screen instructions to add the Soundbar.
• The automatic pop-up (the second screenshot below) may not show on some devices.
If the pop-up window does not appear, press “ + ” on the Home screen. The Soundbar is added to the app.
• The illustration below may differ according to the app version.

Using the Tap Sound
Tap the Soundbar with your mobile device to play the sound of content on the mobile device through the Soundbar.

This function may not be supported, depending on the mobile device.
This function is only compatible with Samsung mobile devices with Android 8.1 or later.

Turn on the Tap Sound function on your mobile device.
• For details on how to turn on the function, refer to “Setting the Tap Sound function” below.
Tap the Soundbar with the mobile device. Select “Start now” in the displayed message window.
A connection is established between the mobile device and Soundbar via Bluetooth.
Play the sound of content on the mobile device through the Soundbar.
• This function connects a mobile device to the Soundbar via Bluetooth by detecting vibration that occurs when the device touches the Soundbar.
• Make sure the mobile device does not tap a sharp corner of the Soundbar. The Soundbar or mobile device may become scratched or damaged.
• It is recommended that the mobile device be covered with a case. Lightly tap the wide area in the upper portion of the Soundbar, without using excessive force.
• To use this function, update the SmartThings app to the latest version.
The function may not be supported, depending on the app version.

Setting the Tap Sound function
Use the SmartThings app to turn on the Tap View, Tap Sound function.

On the mobile device, run the SmartThings app.
Select ( → ) in the SmartThings app screen displayed on the mobile device.
Set “Tap View, Tap Sound” to On to allow the function to work when a mobile device moves close to the Soundbar. The function is turned on.

NOTE

When the mobile device is in power-saving mode, the Tap Sound function does not work.
The Tap Sound function may not work if there are devices near the Soundbar that cause radio interference such as electric devices. Make sure devices that may cause radio interference are placed at a sufficient distance away from the Soundbar.

CONNECTING VIA APPLE AIRPLAY 2

This feature may not be available in some countries.
This Samsung Soundbar supports AirPlay 2 and requires iOS 11.4 or later.

With AirPlay 2, you can stream music, podcasts, and other audio from your Apple devices to the Samsung Soundbar.

Make sure the Soundbar is powered on and connected to the same Wi-Fi network as your Apple device.
Select from an AirPlay-supported app or Control Center on your iPhone, iPad, or Mac.
Select the Soundbar from the list of available devices to play the current audio to.

INSTALLING THE WALL MOUNT

Installation Precautions

Install on a vertical wall only.
Do not install in a place with high temperature or humidity.
Verify whether the wall is strong enough to support the product’s weight. If not, reinforce the wall or choose another installation point.
Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster board, iron board, wood, etc.). If possible, fix the support screws into wall studs.
Purchase wall mounting screws according to the type and thickness of the wall you want to mount the Soundbar on.
- Diameter: M5
- Length: 1 3/8 inches (35 mm) or longer recommended.
Connect cables from the unit to external devices before you install the Soundbar on the wall.
Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an electric shock.

Wallmount Components

Bracket-Wall Mount

Place the Wall Mount Guide against the wall surface.
• The Wall Mount Guide must be level.
• If your TV is mounted on the wall, install the Soundbar at least 2 inches (5 cm) below the TV.
Align the Wall Mount Guide’s Center Line with the center of your
TV (if you are mounting the Soundbar below your TV), and then fix the Wall Mount Guide to the wall using tape.
• If you are not mounting below a TV, place the Center Line in the center of the installation area.
Push a pen tip or sharpened pencil tip through the center of the
A-TYPE images on each end of the Guide to mark the holes for the supporting screws, and then remove the Wall Mount Guide.
Using an appropriately sized drill bit, drill a hole in the wall at each marking.
• If the markings do not correspond to the positions of studs, make sure you insert appropriate anchors or mollies into the holes before you insert the support screws. If you use anchors or mollies, make sure the holes you drill are large enough for the anchors or mollies you use.
Push a screw (not supplied) through each Holder-Screw, and then screw each screw firmly into a support screw hole.
Install the 2 Bracket-Wall Mounts in the correct orientation on the bottom of the Soundbar using 2 Screws.
• When assembling, make sure the hanger part of the BracketWall Mounts are located behind the rear of the Soundbar.
Install the Soundbar with the attached Bracket-Wall Mounts by hanging the Bracket-Wall Mounts on the Holder-Screws on the wall.
Slide the Soundbar down as shown below so that the Bracket-Wall Mounts rest securely on the Holder-Screws.
• Insert the Holder-Screws into the wide (bottom) part of the Bracket-Wall Mounts, and then slide the Bracket-Wall Mounts down so that the Bracket-Wall Mounts rest securely on the Holder-Screws.

Installing the Surround Speakers on a Wall (applicable models only)
You can purchase wall mounts separately to install the surround speakers on a wall.
Wall mounts aren’t sold by Samsung Electronics.

Notes for Wall Mounting the Surround Speakers

Surround Speaker wall mounts must be able to support more than 17.6 lbs (8.0 kg).
Hole size : 1/4 – 20 UNC threaded insert
- Standard Screw : 6.35 mm (0.25 Inch) ø, 1.2 7mm (0.05 Inch) Pitch
- Length : 18 mm (0.70 Inch) long
- Quantity : Left 1 EA / Right 1 EA
Check the strength of the wall before you install the Wall Mount Brackets. If the strength is insufficient, make sure to reinforce the wall before installing the Wall Mount Brackets and the speakers on the wall.
Samsung Electronics is not liable for any damage to the product due to the product being installed inappropriately.
Take care not to install the speakers sideways or upside down.

INSTALLING THE SOUNDBAR IN FRONT OF TV

Component

To install, attach the Rubber-Feet to the bottom of the Soundbar before placing it in position above the TV stand. Make sure you attach the Rubber- Feet so they do not lie outside the edges of the TV stand. Refer to the figure below.

Place the Soundbar on a TV stand.

As illustrated in the image, align the center of the Soundbar with the center of the TV, carefully place the Soundbar onto the TV stand.
At this time, place the microphones (applicable models only) at the front of the stand not to interfere with voice recognition.

NOTE

Make sure the Soundbar is placed on a flat and solid surface.
Insufficient gap from the TV may cause voice recognition and acoustic problems.
The illustration above differs with the respective model.
This function is not supported by Q700B model.

SOFTWARE UPDATE

Auto Update
When the Soundbar is connected to the Internet, software updates automatically occur even when the Soundbar is turned off.

To use the Auto Update function, the Soundbar must be connected to the Internet.
The Wi-Fi connection to the Soundbar will be terminated if the Soundbar’s power cord is disconnected or the power is cut off. If the power is cut off, when the power comes back on or you reconnect the power cord, turn on the Soundbar, and then reconnect it to the Internet.

USB Update

Samsung may offer updates for the Soundbar’s system firmware in the future.
When an update is available, you can update the Soundbar by connecting the USB drive that contains the update firmware to the SERVICE port of the Soundbar.

Go to the Samsung Electronics website (www.samsung.com) → search for the model name from the customer support menu option.
• For more information about update, refer to Upgrade Guide.
Download the upgrade file (USB type).
Unzip the file to create a folder with the file name.
Store the created folder in a USB and then connect it to the Soundbar.
Turn on the Soundbar. Then the product is updated within 3 minutes with displaying the message, “UPDATE”.
• During update, do not turn it off or remove the USB.
• If “UPDATE” does not appear on the display window, remove the power cord from the Soundbar and then reconnect it.
• When the latest version is installed, no update is performed.
• Depending on the USB type, update may not be supported.

Initialization

With the Soundbar on, press the (Volume) buttons on the body at the same time for at least 5 seconds. “INIT” appears on the display and then the Soundbar is initialized.

CAUTION

All the settings of the Soundbar are initialized. Be sure to perform this only when initialization is required.

TROUBLESHOOTING

Before seeking assistance, check the following.

Soundbar does not turn on.

Check whether the power cord of the Soundbar is correctly inserted into the outlet.

Soundbar works erratically.

After removing the power cord, insert it again.
Power cycle the external device and try again.
If there is no signal, the Soundbar automatically turns off after a certain period of time. Turn on the power. (See page 9.)

Remote control does not work

Point the remote directly at the soundbar.
Replace the batteries with new ones.

The Soundbar indicator turns solid red.

The microphone is turned off.
Turn on the microphone. (See page 7.)

Sound is not output from the soundbar.

The volume of the Soundbar is too low or muted. Adjust the volume.
When any external device (STB, Bluetooth device, mobile device, etc.) is connected, adjust the volume of the external device.
For sound output of the TV, select Soundbar. (Samsung TV: Home ( ) → Menu → Settings ( ) → All Settings ( ) → Sound → Sound Output → Select Soundbar)
The cable connection to the Soundbar may not be loose. Remove the cable and connect again.
Remove the power cord completely, reconnect, and turn the power on.
Initialize the product and try again. (See page 35.)

Sound is not output from the subwoofer or the rear speakers.

Check whether the LED indicator on the rear of the Subwoofer and Surround Speakers are on in blue. Reconnect the Soundbar and Subwoofer and Surround Speakers if the indicator is blinking in blue or turned red. (See page 16.)
You may experience an issue if there is an obstacle between the Soundbar and Subwoofer. Move devices to an area away from obstacles.
Other devices sending radio frequency signals in proximity may interrupt the connection.
Keep your speaker away from such devices.
Remove and reconnect the power plug.

In case there is sound jitter, delays, or noise from the Subwoofer and Surround Speaker

If there are any objects between the Soundbar and Subwoofer speaker, this could cause a problem. Please reposition these to a place without such an object.
There may be sound jitter or delays when the Subwoofer and Surround Speaker are far from the Soundbar. Please place them near the Soundbar.
There may be sound jitter or delays when the Soundbar is near an instrument or electrical device that can cause radio interference. Place the Soundbar far from such devices that can cause radio interference. (E.g., wireless router)
Change the TV network connection status from wireless to wired.

The Subwoofer volume is too low

The original volume of the content you are playing may be low. Try adjusting the Subwoofer level. (See page 10.)
Bring the Subwoofer speaker closer to you.

If the TV is not connected via HDMI TO TV (eARC/ARC)

Check whether the HDMI cable is correctly connected to the ARC terminal. (See page 18.)
Connection may not be possible due to the connected external device (set-top box, game machine, etc.). Directly connect the Soundbar.
HDMI-CEC may not be activated on the TV. Turn on the CEC on the TV menu. (Samsung TV: Home ( ) → Menu → Settings ( ) → All Settings ( ) → Connection → External Device Manager → Anynet+ (HDMI-CEC) ON)
To connect with eARC, the eARC function in the TV menu should be set to On. (Samsung TV: Home ( ) → Menu → Settings ( ) → All Settings ( ) → Sound → Expert Settings → HDMI-eARC Mode (Auto))

There is no sound in when connecting to the TV in HDMI TO TV (eARC/ARC) mode

Your device is unable to play the input signal. Change the TV’s audio output to PCM or Dolby Digital. (For a Samsung TV: Home ( ) → Menu → Settings ( ) → All Settings ( ) → Sound → Expert Settings → Digital Output Audio Format)

Soundbar will not connect via Bluetooth.

When connecting a new device, switch to “BT PAIRING” for connection. (Press the PAIR button on the remote control or press the
(Mic On/Off) / (Source) button on the body for at least 5 seconds.)
If the Soundbar is connected to another device, disconnect that device first to switch the device.
Reconnect it after removing the Bluetooth speaker list on the device to connect. (Samsung TV: Home ( ) → Menu → Settings ( ) → All Settings ( ) → Sound → Sound Output → Bluetooth Speaker List)
The automatic TV connection may be disabled. While the Soundbar is in “BT READY”, press and hold the Left button on the Soundbar remote control for 5 seconds to select ON-TV CONNECT. If you see OFF-TV CONNECT, press and hold Left button again for 5 seconds to switch the selection.
Remove and reconnect the power plug, then try again.
Initialize the product and try again. (See page 35.)

Sound drops out when connected via Bluetooth.

Some devices can cause radio interference if they are located too close to the Soundbar. e. g. microwaves, wireless routers, etc.
If your device that is connected via Bluetooth moves too far away from the soundbar, it may cause the sound to drop out. Move the device closer to the soundbar.
If a part of your body is in contact with the Bluetooth transceiver or the product is installed on metal furniture, the sound may drop out. Check the installation environment and conditions for use.

Soundbar will not connect to Wi-Fi.

Check whether your wireless router is on.
Turn off the router, turn it back on, and then try again.
The soundbar will not connect if the wireless signal is too weak.
Try moving the router closer to the soundbar, or eliminating any obstacles that are between the soundbar and the router, if possible.
If your wireless router is new, you will need to reconfigure the speaker’s network settings.

The soundbar does not turn on automatically with the TV.

When you turn off the Soundbar while watching TV, power synchronization with the TV is disabled. First turn off the TV.

The AVA function (applicable models only) is not available in the following cases.

The AVA function (applicable models only) will not be available using Q-symphony function.
The AVA function (applicable models only) will not be available when the microphone is turned off.

After connecting the TV to the Soundbar, I switched the Soundbar mode. Then no sound is output from the TV.

If you connect your Soundbar to a mobile device while the Soundbar is connected to the TV, the Soundbar outputs sound from the mobile device while keeping the TV connection. So the TV sound will not be delivered anywhere.
Disconnect the mobile device, and the TV sound will be output from the Soundbar again.

LICENSE

ATMOS

Dolby, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation.
Manufactured under license from Dolby Laboratories. Confidential unpublished works. Copyright © 2012-2021 Dolby Laboratories. All rights reserved.

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. (for companies headquartered in the U.S./ Japan/Taiwan) or under license from DTS Licensing Limited (for all other companies). DTS, DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and other countries. © 2021 DTS, Inc. ALL RIGHTS RESERVED.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

Use your phone, tablet or computer as a remote control for Spotify. Go to spotify.com/connect to learn how
The Spotify Software is subject to third party licenses found here: https://www.spotify.com/connect/third-party-licenses.
Apple, Airplay, iPhone, iPad, and Mac are trademarks of Apple
Inc., registered in the U.S. and other countries.
Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards.

OPEN SOURCE LICENSE NOTICE

To send inquiries and requests for questions regarding open sources, contact Samsung Open Source (http://opensource.samsung.com)

IMPORTANT NOTES ABOUT SERVICE

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

SPECIFICATIONS AND GUIDE

Specifications
Soundbar Main Unit

Model Name	HW-Q930B
Weight	11.9 lbs (5.4 kg)
Dimensions (W x H x D)	43.7 x 2.38 x 4.7 inches

(1110.7 x 60.4 x 120.0 mm)
Operating Temperature Range| +41°F to +95°F (+5°C to +35°C)
Operating Humidity Range| 10 % ~ 75 %
AMPLIFIER Rated Output power| (30 W x 3) + (20 W x 6) + (10 W x 3)
Supported play formats| Dolby 5.1ch / Dolby Digital Plus / Dolby TRUE HD / Dolby ATMOS /
DTS 5.1ch / DTS HD / DTS-HD Master Audio / DTS:X / LPCM 8Ch
Model Name| HW-Q800B
Weight| 11.2 lbs (5.1 kg)
Dimensions (W x H x D)| 43.7 x 2.38 x 4.7 inches
(1110.7 x 60.4 x 120.0 mm)
Operating Temperature Range| +41°F to +95°F (+5°C to +35°C)
Operating Humidity Range| 10 % ~ 75 %
AMPLIFIER Rated Output power| (30 W x 3) + (20 W x 4) + (10 W x 3)
Supported play formats| Dolby 5.1ch / Dolby Digital Plus / Dolby TRUE HD / Dolby ATMOS /
DTS 5.1ch / DTS HD / DTS-HD Master Audio / DTS:X / LPCM 8Ch
Model Name| HW-Q700B
Weight| 10.6 lbs (4.8 kg)
Dimensions (W x H x D)| 43.7 x 2.38 x 4.7 inches
(1110.7 x 60.4 x 120.0 mm)
Operating Temperature Range| +41°F to +95°F (+5°C to +35°C)
Operating Humidity Range| 10 % ~ 75 %
AMPLIFIER Rated Output power| (30 W x 3) + (20 W x 2) + (10 W x 3)
Supported play formats| Dolby 5.1ch / Dolby Digital Plus / Dolby TRUE HD / Dolby ATMOS /
DTS 5.1ch / DTS HD / DTS-HD Master Audio / DTS:X / LPCM 8Ch

Subwoofer

Subwoofer Name	PS-WB96B
Weight	21.6 lbs (9.8 kg)
Dimensions (W x H x D)	8.3 x15.9 x15.9 inches

Surround Speaker (applicable models only)

Wireless Surround Speaker SET Name	PS-RB96B (LEFT/RIGHT)
Weight	6.8 lbs (3.1 kg)
Dimensions (W x H x D)	5.1 x 7.9 x 5.5 inches (129.5 x 201.3 x 140.4 mm)
AMPLIFIER Rated Output power	140 W

NOTE

Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
Weight and dimensions are approximate.
Precaution : The Soundbar will restart automatically if you turn on/turn off Wi-Fi.

Wi-Fi Port deactivation method| Press the CH LEVEL button on the remote control of the Soundbar for 30 seconds to turn Wi-Fi On / Off.
---|---
Bluetooth Port deactivation method| Press the TONE CONTROL button on the remote control of the Soundbar for 30 seconds to turn Bluetooth On / Off.

LIMITED WARRANTY TO ORIGINAL PURCHASER

Samsung Electronics Canada Inc.(SECA), warrants that this product is free from defective material and workmanship.
SECA further warrants that if this product falls to operate properly within the specified warranty period and the failure is due to improper workmanship or defective materials, SECA will repair or replace the product at its option.
All warranty repairs must be performed by a SECA Authorized Service Center. (The name and address of the location nearest you can be obtained by calling toll free: 1- 800- SAMSUNG)

LABOR	PARTS
One year (Carry- in)	One year

On carry-in models, transportation to and from the service center is the customer’s responsibility.
The original dated sales receipt must be retained by the customer and is the only acceptable proof of purchase. It must be presented to the authorized service center at the time service is requested.

EXCLUSIONS (WHAT IS NOT COVERED)
This warranty does not cover damage due to accident, fire, flood and/ or other acts of God; misuse, incorrect line voltage, improper installation, improper or unauthorized repairs, commercial use or damage that occurs in shipping. Exterior and interior finish, lamps, glass are not covered under this warranty. Customer adjustments which are explained in the instruction manual are not covered under the terms of this warranty. This warranty will automatically be voided for any unit found with a missing or altered serial number. This warranty is valid only on products purchased and used in Canada.

Samsung Electronics Canada Inc
2050 Derry Rd West
Mississauga, On. L5N 0B9
Tel: 1-800-SAMSUNG (726-7864)
Fax: (905) 542- 1199
Website: www.samsung.com/ca

© 2022 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Center.

HEADQUARTERS
Samsung Electronics Canada Inc. 2050 Derry Road West, Mississauga, Ontario L5N 0B9 Canada
TEL: 1-800-SAMSUNG (1-800-726-7864)
www.samsung.com/ca/support