SONY KLV-S19A10 19 Inch HDTV-ready LCD TV User Guide
- June 9, 2024
- Sony
Table of Contents
SONY KLV-S19A10 19 Inch HDTV-ready LCD TV
Checking the Supplied Accessories
- Remote control (RM-YA001) (1) and size AA batteries (2)
- 75-ohm coaxial cable (ferrite core attached) (1)
- AC power cord (1)
- AC power adaptor (1) (KLV-S19A10 only)
- HD15-HD15 cable (1)
- Support belt (1), securing screw (1) and wood screw (1)
- Operating Instructions (1)
- Quick Setup Guide (1)
- Leaflet (Installing the Wall-Mount Bracket to the TV) (1)
- Warranty Card (1)
Inserting Batteries into the Remote Control
- Insert two size AA batteries (supplied) by matching the + and – on the batteries to the diagram inside the remote control’s battery compartment.
Connecting Your TV
- Review the following chart to determine which diagram to use to connect the components in your system:
- See the “Cables Required” chart that appears with the diagram to determine which cables you’ll need. You may need to purchase extra accessories, such as cables and splitters, depending on the components you plan to connect.
- Turn off and unplug all components before making connections.
- If you are connecting a digital cable box, you’ll need a special bidirectional splitter that’s compatible with your cable box. Contact your cable provider for details.
Making Video Connections
- Your TV includes several types of video inputs. Use the inputs that are available on your components that provide the best video performance, as shown in the table on the right.
Best Video Performance
Additional Connections
For best audio performance, connect your digital audio components using either digital optical or digital coaxial audio connections. Depending on which components are in your system, you may need to complete additional connections. For example, if you have a satellite receiver, you’ll need to connect the satellite antenna. If you have an A/V receiver, you’ll need to connect speakers.
Notes
- The connection diagrams shown on the reverse side are recommendations only; other possible solutions may exist. Connections that include an A/V receiver can often be very complex, so check your A/V receiver’s instruction manual for additional details.
- See the Operating Instructions when connecting to a personal computer.
Running Initial Setup
- Press POWER to turn on the TV.
- The Initial Setup screen appears.
- Press or to select the on-screen display language. Then press .
- The message “First please connet cable/antenna” appears.
- Note: By default, Auto Program is set to scan cable TV channels.
- Press CH+ to start Auto Program.
Auto Program automatically creates a list of receivable channels. When finished, the lowest numbered channel is displayed. When all the receivable channels are stored, the “Show/Hide Channels” settings appear.
To scan available VHF/UHF antenna channels instead of the cable TV channels
- Select Settings in WEGA GATE, then go to Channels settings.
- Set Cable to Off.
- Start Auto Program by pressing CH+.
To perform Auto Program again, follow the above instructions. Depending on your signal source, be sure to set Cable to On or Off accordingly (see Operating Instructions).
Note: The Initial Setup menu will appear each time the TV is turned on until you complete the scanning for the available channels.
Programming the Remote Control
The remote control is preset to operate Sony brand video equipment.
- Sony Equipment: Programmable Code Number
- DVD/VCR 601: (Sony Dream System)
- SAT/Cable 801: (Sony Satellite Receiver)
Follow the steps below to program your TV’s remote control to operate the non- Sony video equipment. Using the code list below, find the three-digit code number for the manufacturer of your equipment. (If more than one code number is listed, use the number listed first.)
- Press and hold the FUNCTION button you want to program on the remote control and press the button simultaneously. The selected FUNCTION button (DVD/VCR or SAT/CABLE) will flash.
- Enter the three-digit manufacturer’s code number using the 0-9 buttons while the button is lit, approximately 10 seconds.
- Press button. When the programming is correct, the selected FUNCTION button will flash twice slowly, and when not, flashes five times quickly.
To check if the code works
Aim your TV’s remote control at the equipment, and press the green POWER button. If the equipment responds, the programming is completed. If not, try the next code listed.
Tips
- If no code is input within the above specified time, or an invalid or incorrect code number is input, the remote control automatically goes back to the previous setting.
- In some cases, you may not be able to program your remote control to operate other equipment. In such cases, use the equipment’s own remote control.
- Dead batteries or removing the batteries may cause the programmable codes to be lost and revert back to factory settings. Reprogramming the codes may be necessary.
Manufacturer’s Codes
- If an Aiwa VCR does not work even though you enter the code for Aiwa, enter the code for Sony instead.
CONNECTIONS
Use this diagram if you have
Cable/Antenna VCR DVD OR
Cables Required
- Splitter: 1
- Coaxial: 4
- Composite: 2
- Component: 1
- Audio: 1
- If your DVD player or satellite receiver has an HDMI jack, use that instead of the video connections shown here.
- If you are not using a cable box or satellite receiver, connect your cable or antenna to the VCR’s RF IN jack.
Use this diagram if you have
Cable/Antenna VCR DVD Player OR
Cables Required
- Splitter: 1
- Coaxial: 4
- Composite: 3
- Component: 1
- Audio: 2
- If your DVD player or satellite receiver has an HDMI jack, use that instead of the video connections shown here.
- If you are not using a cable box or satellite receiver, connect your cable or antenna to the VCR’s RF IN jack.
Use this diagram if you have
Cable/Antenna VCR DVD Player
Cables Required
- Splitter: 1
- Coaxial: 6
- Composite: 3
- Component: 1
- HDMI: 1
- Audio: 1
- The DVI-HDTV VIDEO connector does not provide audio, so audio cables must be connected to provide sound when a DVI to HDMI adaptor is used.
- If you are not using a cable box, connect your cable or antenna to the VCR’s RF IN jack.
Use this diagram if you have
Cable/Antenna OR
Cables Required
- Splitter: 1
- Coaxial: 3
- Composite: 3
- Component: 1
- Audio: 2
- If your DVD player or satellite receiver has an HDMI jack, use that instead of the video connections shown here.
- If you are not using a cable box or satellite receiver, connect your cable or antenna to the VCR’s RF IN jack.
Use this diagram if you have
Cable/Antenna VCR DVD Player OR
Cables Required
- Splitter: 1
- Coaxial: 3
- Composite: 2
- Component: 1
- HDMI: 1
- Audio: 1
- The DVI-HDTV VIDEO connector does not provide audio, so audio cables must be connected to provide sound when a DVI to HDMI adaptor is used.
- If your cable box has a DVI jack, use that instead of the video connections shown here.
Use this diagram if you have
Cable/Antenna OR
Cables Required
- Splitter: 1
- Coaxial: 4
- Composite: 2
- Composite: 1
- (without Audio)
- Component: 1
- If you are not using a cable box or satellite receiver, connect your cable or antenna to the VCR’s RF IN jack.
Satelite Antenna Cable not shown.
This file has been downloaded from: www.UsersManualGuide.com
User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, DVD, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner’s, manual guide, manual operation, operating manual, user’s manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual.
If your product is not working properly
DO NOT RETURN TO THE STORE.
For service and technical assistance
- Call our Customer Information Service Center (Toll-Free): 1-800-222-SONY (7669) for US residents.
- 1-877-899-SONY (7669) for Canadian residents.
Sony Corporation © 2005 Printed in Japan