make it real 1515 Mega Jewelry Studio Instructions
- June 9, 2024
- make it real
Table of Contents
make it real 1515 Mega Jewelry Studio Instructions
Instructions
Legend
Scissors
Ruler
Adhesive tape
Craft glue
Knot
Double knot
Let dry
Repeat
READ THE INSTRUCTIONS ALL THE WAY TO THE END BEFORE STARTING YOUR PROJECT.
Install the PlayTray by taping it to a flat surface as shown.
Gut a 25 cm (9.5 in) long piece of clear plastic cord.
Thread the beads onto the cord as shown.
Make a double knot with the ends of the cord.
Use a drop of craft glue to secure the knot Cut off the excess cords after the
knot.
Cut three 30 cm (12 in) long pieces of purple cord. Cut a 30 cm (12 in) long piece of blue cord.
Use adhesive tape to secure the PlayTray to the work surface.
Make a simple knot with the ends of the ‘a’ purple cord. Secure the knot in a slot of the Playtray.
Tape the t’ threads on either side of the ‘a’ cords as shown.
Leaving 12.5 cm (5 in) free, begin making a braid of square knots following
the steps.
Repeat step 5 until there are 5 cm (2 in) of knots and 12.5 cm (5 in) of cord
on either side of the knots.
Cross the ends of the cords in opposite directions.
Make a simple knot with the right cords to the left cords as shown. Tighten
the knot.
Cut two lengths of 30 cm (12 in) long clear plastic cords.
Tape both ends of the cords to the work surface.
Tape both ends of the cords to the work surface.
Thread a bead up the left cord only.
Thread 4 beads through both cords.
Thread a bead up the left cord only.
Thread a gold ring through both cords.
Thread the next bead up the right cord only.
Continue steps ‘A’ to ‘D’,a Iternating beads and rings.
Continue step 5 until the desired length is reached.
Make a double knot with the ends of the cord.
Use a drop of craft glue to secure the knot. Cut off the excess cords after
the knot.
Cut both ends of the ribbon to a taper point.
Seal each end with craft glue and wait for it to dry.
Slide the pendant onto the braid.
Slide the large white bead through one ribbon end.
Thread the other end of the ribbon through the bead in the opposite direction.
Make a simple knot on each end of the ribbon, leaving some space. Thread a
purple bead onto each end.
‘Add the seashell beads to the inside of the pendant.
Clip on the mermaid charm to finish your necklace!
Cut the green ribbon to a length of 25 cm (9.5 in).
Begin threading the ribbon, alternating through the chain links as shown.
Halfway through, slide the tassel onto the ribbon.
Continue threading the ribbon through the rest of the chain
Make a double knot with the ends of the ribbon.
Cut the excess ribbon ends after the knot.
Cut a 15 cm (6 in) long piece of clear plastic cord.
Thread the beads onto the cord following the pattern shown.
Make a double knot with both ends of the cord. Seal the knot with a drop of craft glue and cut off the excess cords after the knot.
Avoid soaking the bracelets in water.
WARNING!
CHOKING HAZARD – small parts. Not suitable for children under 3 years.
STRANGULATION HAZARD – Functional long cord — Adult supervision required.
MAKE IT REAL
1700 Reisterstown Rd Ste 214
Pikesville MD 21208 USA
410-995-8685
© 2022 MAKE IT REAL, LLC
Jactin House, 24 Hood Street
Ancoats, Manchester, M4 6WX UK
+44 (0) 161 302 4100
EUCEREP B.V.
Roald Dahllaan 33, 5629MC, Eindhoven, NL
+31685008887