kleenmaid RHUC92 Fixed Undermount Rangehood User Manual

June 9, 2024
kleenmaid

kleenmaid RHUC92 Fixed Undermount Rangehood User Manual

Safety Warning

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
  • Children shall not play with the appliance.
  • Cleaning and user maintenance shall not be made by children without supervision.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
  • There should be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels.
  • The filter is made of high-density aluminum.
  • Please do not use corrosive detergent for cleaning.
  • Regular maintenance is recommended for the unit to continue to function properly.
  • To protect the main body from corrosion due to the accumulation of dirt over time the rangehood should be cleaned With hot water and non-corrosive detergent every two months.
  • There is a fire risk if cleaning is not carried out in accordance with the instructions.
  • Do not flambé under the rangehood. Exhaust air must not be discharged into an existing flue which is used for exhausting fumes from appliances burning gas or other fuels.
  • The safety gap between the range hood and the hob below must comply with the recommendations of the hob manufacturer.
  • In case of no instructions, a minimum distance of 650mm (or other minimum distance as may be specified by AS/NZS 5601 and interpreted by a certified installer) should apply.
  • Regulations concerning the discharge of air must be fulfilled.
    CAUTION:  Accessible parts may become hot when used with cookina appliances

Measurement

Note: measurements are in mm.

Installation

NOTE: Before making preparations for or commencing installation, the installer should refer to the current online version of the User Manual, which is available on the Kleenmaid website (see back cover for details). Two venting modes are available, extraction-air mode and recirculation mode. Select desired mode before installation.

  • Press the lock catch of metal filter, remove the filiter.

  • Remove the stainless steel frame by unfastening the4 screws (M4″10) and the other 2 screws (M4*8).

  • Unfastenin the screws (ST4″10). remove the lid of terminal box, disconnect the wires to the commands at the connectors.

  • Disconnect the wires to the light at the connectors.

  • Fasten the hood in the cabinet by using the 12 screws (ST4″18)

  • Screw the stainles3 steel frame back into place using the screws removed as described above.

  • Reconnect the wires to the commands and light.

  • Replace the metal filter. Install the air outlet pipe (optional).

  • Rigid pipe recommended.

Use

  • Speed adjustment. See the figure below.
  • Rotate the knob to the Stop graphic, the motor will stop running.
  • Rotate the knob to the Light graphic, the two lighting lamps will come on.
  • Rotate the knob to the Low (speed) graphic, the motor runs at low speed, two lights on.
  • Rotate the knob to the Mid (speed) graphic, the motor runs at mid speed, two lights on.
  • Rotate the knob to the High (speed) graphic, the motor runs at high speed, two lights on.

Maintenance

Maintenance and replacement of your Kleenmaid Rangehood Filters. Your Kleenmaid rangehood has one or both of the following types of filters:

  1. The visible aluminium or stainless steel grease filter, which should be present on every rangehood. These filters should be removed, cleaned and re-installed at least every three months, and more often if food is regularly fried or grilled. These fiters may be cleaned either with a soft-bristled brush in warm soapy water, or in a dishwasher (without other items). Make sure that the rangehood is turned off before cleaning. Ensure that each filter is completely dry before re-installing it into the range hood. Normally these fiters will last the life of the rangehood, however if they are damaged in any way, replacements may be purchased by visiting the Kleenmaid website www.kleenmaid.com.au emailing support@kleenmaid.com.au or callina 02 9310 1207
Cleaning of the filter
  • Removing the metal filter according to Installation instructions (p7) Put it into a dishwasher with detergent, set the temperature to below 60 degrees.
  • Please do not use abrasive detergent as it will damage the rangehood.
  • Make sure that power to the rangehood is shut off before cleaning.

Warning:  It must be ensured that the grease filters are correctly installed whenever the range hood is operating. Failure to do so may damage the range hood, and such damage will not be covered by the manufacturers.

The internal Kleenmaid Activated Charcoal (or “Carbon”) Filter, should be present on a range hood that is installed in recirculating mode i.e. not vented outdoors.
These filters are located inside the rangehood and remove cooking odors from the air. These filters cannot be cleaned and will require replacement. The effective life of the filter depends on the type and amount of cooking you do. Generally, the life of these filters is approximately six months. However, always replace the filter when it no longer absorbs odors effectively. When replacement Activated Charcoal filters are required they may be purchased by visiting the Kleenmaid website www.kleenmaid.com.au, emailing support@kleenmaid.com.au or calling 02 9310 1207. Order Code KMCF200

Changing the filter
  • Remove the metal fitler according to the Installation instructions (p7)
  • Remove the saturated activated charcoal fiters as indicated in the diagram below.
  • Ft the new charcoal fiters, as indicated in the diagram below.
  • Replace the metal filter according to the Installation instructions (p 8).

Replacing the lamp

  • Press the lock catch of the metal Filter, and remove the Filter.

  • Push the lamp from the inside, to remove the Lamp.

  • Disconnect the wires to the Lamp.

  • Connect the wires of the new Lamp.

  • Push the new Lamp from outside and fix it to the hole.

| Max Power| Voltage| Picture| Lamp Cap| ILCOS D code
---|---|---|---|---|---

Square / Diameter

: 33.2mm x 120mm

|

1.5W

|

DC 12 V

| |

——

|

DSS-1.5-S-33.2

/120

Trouble Shooting

Fault Cause Solution

Light on, but motor does not work.

| The blades are blocked.|
The capacitor is damaged.| Replace capacitor.
The motor is damaged.| Replace motor.
The internal wiring of motor is cut off / disconnected. An unpleaseant smellmay be produced.| Replace motor.
Both light and motor do not work.| Apart from the above mentioned, check the following:
Light damaged.| Replace lights.
Power cord loose.| Connect the wires electric diagram.| as| per| the

Oil leakage.

| Outlet and the air ventilation entranceare not tightly sealed.| Take down the outlet and seal withglue.
Leakage    from   the    connectionU-shaped section and cover.| of| Take U-shaped section down andseal with soap or paint.

Vibration.

| The blade, if damaged, can cause vibrating.| Replace the blade.
The motor is not tightly fastened.| Fasten the motor tightly.
The rangehood is not tightly fixed.| Fixed the rangehood tightly.

Insufficient suction.

| The distance between therangehood and the cookop is too large.| Readjust the distance.
Too much ventilation from open doors or windows.| Choose a new place to install theappliance or close some doors / windows.

The machine inclines.

| The    fixing    screws    are    not    tightenough.| Tighten the fixing screw and makeit horizontal.
The hanging      screws are not tightenough.| Tighten the hanging screw andmake it horizontal.

Electrical Diagram

Electrical diagram see label on main body of the actual product.
WARNING:  MUST BE ENSURED THAT THIS APPLIANCE IS SUPPLIED WHICH CONTINUOUSLY COMPLIES WITH THE RELEVANT AUSTRALIAN STANDARD. FAILURE TO DO SO MAY SERIOUSLY DAMAGE THE APPLIANCE AND ANY SUCH DAMAGE IS NOT COVERED A BY THE MANUFACTURER’S WARRANTY.

Main Parameters

Voltage 220-240V~ 50Hz
Rated Power 213W
Lighting Power 1.5W x 2
Motor Power 210W
Diameter of air tube 150mm
Air flow Max 900m 3/h (air flow meter)
Noise 56 dB(A) at Low Speed

The air flow parameter is tested under conditions of 230V 50Hz when the voltage is 220-240V 50Hz and without carbon filters.

Disposal

Please dispose of it at your local community waste collection recycling center and ensure it presents no danger to children while being stored for disposal. The plug must be rendered useless and the cable cut off to prevent misuse.

KLEENMAID WARRANTY

TERMS AND CONDITIONS
  1. Compass customer as Capital set out Services herein. Pty Ltd ABN 96 138 214 525 trading as
  2. Kleenmaid will provides parts and labor to you the 2 Kleenmaid’s Products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major faiure and for compensation for any other reasonably foreseeable loss or damage.
  3. You are also entiled to have the goods repaired or replaced itf the goods fail to be of acceptable quality and the failure does not amount to a major tenure. The benefits given to you under this Kleenmaid Warranty are in addtion to other ights and remedies to which you may be entited under the Australian Consumer Law in relation to the Product to which this Kleenmaid Warranty relates. Subject to the conditions below. the Product is warranted by Kleenmaid andiron ts agents to be tree from defects in materials and workmanship for the Warranty Period for nomal Domestic Use.
  4. Product densification:
  5. Kleenmaid reserves the right to reject claims for any services or work where you cannot produce Tor verification the serial number and proof of purchase for the Product (including but not limited to the original invoIce).
  6. this Kleenmaid Warranty will be voided if the serial number for the Product cannot be verified.
  7. This is not intended to exclude, restrict or modify any right or remedy to which you may otherwise be entitled under the consumer guarantee provisions of the Australian Consumer Law.
  8. Kleenmaid Warranty where the serial number for the Product cannot be verified or you cannot produce for verification proof of purchase for the Product (including but not limited to the original invoice), the repairer will not carry out any repairs on the Product and you will be charged a service call-out fee.
  9. What is covered by this Kleenmaid Warranty:
    • the Product is covered for faulty workmanship or parts that have failed under normal Domestic Use.
    • Kleenmaid and/or its agents will determine by objective testing if there are any defects in the Product and/or faulty workmanship.
    • this Kleenmaid Warranty is only applicable if repairs on Products are carried out within Mainland Australia.
    • this Kleenmaid Warranty:
    • coversa Product purchased as new, manufactured for use in Mainland Australia;
    • commences from the date of delivery of the Product;
    • provides for the labour and replacement parts necessary to maintain the Product in good operating condition as specified in this Kleenmaid Warranty, however, if repair is needed because of a Product failure during normal Domestic Use, Kleenmaid has the option to repair or replace the defective Product or part of the Product with a product or part of like kind and quality. A replacement part may be new or reconditioned of like kind and quality and may cost less than the original Product purchased and no charges or refunds will be made based on the replacement product or part cost difference, and
    • is only annlicahle when the Product is used and onerated in accordance with the manufacturer’s instructions
  10. What is not covered by this Kleenmaid warranty (excluded)
    • any damage or failure to or of the Product or part of the Product due to the Product being inadequately serviced to manufacturer’s recommendations; ii. resulting from environmental conditions including and not limited to dirt, dust, rodents, insects, rust, corrosion, salt built-up, of or in any part of the Product; i. resulting from excessive use but fair wear and tear is excepted;
    • resulting from poor installation including and not limited to positioning and externally fited equipment such as plumbing and drainage, cabling, antennae or due to incompatibility of connected equipment
    • caused by overheating as a result of sitting or positioning of the Product, where there is no provision for adequate ventilation or adequate protection from excessive dust;
    • if the Product has been dismantled, repaired or serviced by any person other than someone authorized by Kleenmaid or its agents or representatives;
    • caused by power surges or spikes, including and not limited to, mains power and telecommunications connections, or to other unspecified sources, incorrect power current, voltage fluctuation, amperage fluctuation, rust Or corrosion;
    • it the Product is dropped, the collision of the Product with another object, use for which the Product is not designed, damage to the Product caused by your own negligence, accidental or deliberate misuse of the Product by you, theft, abuse, vandalism, flood, fire, earthquake, electrical storms or any other act of God or any war-related events
    • due to the introduction of abnormal heat loads to the Product
    • costs of attendance and testing where no fault or defect covered by the terms of this Kleenmaid Warranty is identified in the Product;
    • initial setup and installation of the Product
    • normal maintenance costs and costs incurred through the installation of items listed as requiring periodic replacement
    • Products with removed or altered serial numbers
    • broken or cracked glass other than transport damage to the initial point of delivery
    • consumables such as but not limited to bulbs/globes, seals, filters, batteries, and remote controls
    • removal and reinstallation of an internal component not performed by an authorized Kleenmaid agent or representative or authorized service center cosmetic or structural items;
    • or any failures due to interference from or With other products and/or sources.
  11. This Kleenmaid warranty ceases if:
    • the Product ceases to carry the original manufacturer’s serial number or is sold at an auction;
    • the Product is rented
    • there is failure to pay monies owing on invoices as a result of non-warranty work being carried out at the request of the end user as per point 16 below.
  12. Neither Kleenmaid nor its representatives provide loan equipment under the terms of this Kleenmaid Warranty.
  13. Any unauthorised access to the internal hardware of the Product will void this Kleenmaid Warranty.
  14. Repair Notice: Products presented for repair may be replaced by refurbished Products of the same type rather than being repaired. Refurbished parts may be used to repair the Products.
  15. Replacement items are “like for like” and is not “new for old’”‘ and does not indicate in any way that a faulty Product will be replaced with a new part or unit. “Like for like” may either be a quality checked, refurbished or reconditioned unit of the same or later batch of model/size specifications
  16. The cost of making a claim under this Kleenmaid Warranty is not covered by Kleenmaid, including any costs of transportation or travel expenses between your home and your nearest authorised service agent.
  17. Kleenmaid accepts no liability for items that are lost, damaged, or stolen as a result of freight, transport or storage. If you are required to transport the Product to an authorised service centre, you must ensure that it is securely packed and insured.
  18. On Public Holidays or other periods when regular business and wholesale operations are temporarily ceased, repairer availability and warranty response times may extend beyond the standard response times due to the unavailability of repairers and parts.
  19. For any repair performed on a Product under this Kleenmaid Warranty where no fault can be found, or the item is deemed by Kleenmaid or an authorised agent, to be not faulty under this Kleenmaid Warranty, or the repair or fault is not covered under this Kleenmaid Warranty, a ‘No Fault Found’ fee is payable by you. Kleenmaid will advise you of this cost and seek your agreement to pay such costs before commencing such repairs.
  20. Any repairs or services required that are outside the terms and conditions of this Kleenmaid Warranty can be carried out at your request at your cost (including where the Product has not been installed or set up correctly). Kleenmaid will always advise you of this cost and seek your agreement to pay such costs before commencing such repairs. A credit card may be required prior to the commencement of such services
  21. Extra charges wil be payable by the customer should the Product not be readily accessible without special equipment, such as but not limited to cranes and lifts or should the Product be installed in a position that service access is blocked and/or repair work is not possible without uninstalling the Product to gain access.
  22. You, the customer, may be entitled to purchase an extended warranty in respect of the Product. Any extended waranty will not be issued by Kleenmaid but by a third party. Any extended warranty services will be provided directly by the third party as principal and not as agent for Kleenmaid, under their extended warranty terms and conditions and not under this Kleenmaid Warranty
  23. To make a claim under this Kleenmaid Warranty, please have your proof of purchase and the serial number of the Product ready and call (02) 9310 1207 during business hours.
  24. This Kleenmaid Warranty is given by: Name: Compass Capital Services Pty Ltd ABN 96 138 214 525 trading as Kleenmaid Business address: Level 2, Suite 3, 204 Botany Rd, Alexandria NSW Australia 2015 Telephone: (02) 9310 1207
  25. Definitions
    • Australian Consumer Law means the Competition and Consumer Act 2010 (Cth).
    • Domestic Use means use of the Product for personal, domestic or household purposes.
    • Kleenmaid means Compass Capital Services Pty Ltd ABN 96 138 214 525 trading as Kleenmaid.
    • Mainland Australia means the following States and Territories of Australia: New South Wales, Victoria, South Australia, Western Australia, Queensland, Tasmania, Northern Territory, and Australian Capital Territory.
    • Product means the appliance sold by Kleenmaid to you as evidenced by the original purchase invoice.
    • Warranty Period means the period of 60 months for domestic use, 12 months for non-domestic use or such alternative period as may be specified.

UPDATE NOTICE:  This Kleenmaid Warranty is current as at 1 January 2019 but is subject to variation from time to time. For the latest version of the Kleenmaid Warranty, please see our website https://kleenmaid.com.au/warranty/ or phone us on (02) 9310 1207.

Other products available in the Kleenmaid range of appliances
  • Washing machines
  • Clothes dryers
  • Dishwashers
  • Ovens
  • Cooktops
  • Steam ovens
  • microwave ovens
  • Built-in express
  • coffee machines
  • Rangehoods
  • Freestanding ovens
  • Refrigerators & Freezers
  • Beverage Serving Cabinets
  • Water Dispensers
  • Vacuum Cleaners

Read More About This Manual & Download PDF:

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

kleenmaid User Manuals

Related Manuals