Kleenmaid RHSC91 Wall Mounted Canopy Rangehood Instruction Manual

Wall Mounted Canopy Rangehood
Model No: RHSC61_RHSC91

Cooking collection
Instructions for use and warranty details

To register your warranty or make a warranty claim, scan this QR code:

http://www.kleenmaidwarranty.com.au/

Dear Customer,
Thank you and congratulations for choosing Kleenmaid.
Your new appliance has been designed and meticulously tested to ensure that it meets all your culinary requirements, and has been carefully manufactured using top-quality materials to give you years of reliable performance.
For best results, carefully read the instructions on how your new appliance is to be installed. Correct installation will avoid delays and unnecessary service call costs.
Once installation is complete, please read this instruction manual carefully and get to know the controls and the features of your new Kleenmaid appliance. These simple instructions will enable you to achieve excellent results from the very first time you use it.
Again, congratulations and thank you for choosing The Best You Can Own.
KLEENMAID

RECOMMENDATIONS AND SUGGESTIONS

Before using this appliance please study this entire User Manual carefully. Keep this manual in a safe place for future reference. Ensure that other people using the product are familiar with these instructions as well. The latest version of this manual is available on our website. (See back page for details.)

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.

• The safety gap between the range hood and the hob below must comply with the recommendations of the hob manufacturer. In case of no instructions, a minimum distance of 650mm (or other minimum distance as may be specified by AS/NZS 5601 and interpreted by a certified installer) should apply.

• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the hood.

• For Class I appliances, check that the domestic power supply guarantees adequate earthing.

• Connect the extractor to the exhaust flue through a pipe of a minimum diameter of 120mm.
  The route of the flue must be as short as possible.

• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances),a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electricity, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes from being drawn back into the room by the cooker hood.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Regulations concerning the discharge of air have to be fulfilled.

USE

• The range hood is only for home use. It is not suitable for barbecues, roast shops, and other commercial purposes.
• Never use the hood for purposes other than for which it has been designed. z Never leave high naked flames under the hood when it is in operation. z Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. Do not flame under the range hood due to the risk of fire.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capacities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their wellbeing.
• Children should be supervised to ensure that they do not play with the appliance. z Cleaning and user maintenance should not be done by children without supervision.
• “CAUTION: Accessible parts may become hot when used with cooking appliances”.

MAINTENANCE

• The cooker hood and its filter should be cleaned regularly according to the instruction.
• Switch off or unplug the appliance from the main supply before carrying out any maintenance work.
• Clean and/or replace the Filters after the specified period (Fire hazard). z Clean the hood using a damp cloth and a neutral liquid detergent. z The appliance uses 4 hob elements at most.

DISPOSAL OF OLD ELECTRICAL APPLIANCES

The symbol on the packaging indicates that this product may not be treated as household waste. Instead, it should be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about the recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product.

COMPONENTS

WARNING: IT MUST BE ENSURED THAT THIS APPLIANCE IS CONNECTED ONLY TO A 230VAC +10%/-6% 50Hz MAINS POWER SUPPLY WHICH CONTINUOUSLY COMPLIES WITH THE RELEVANT AUSTRALIAN STANDARD. FAILURE TO DO SO MAY SERIOUSLY DAMAGE THE APPLIANCE AND ANY SUCH DAMAGE IS NOT COVERED BY THE MANUFACTURER’S WARRANTY.

DIMENSIONS

INSTALLATION

NOTE: Before making preparations for or commencing installation, the installer should refer to the current online version of the User Manual, which is available on the Kleenmaid website (see back cover for details).

CHOOSE A VENTING MODE

This rangehood may be installed in one of 2 venting modes – ducted extraction- air mode and recirculation mode. The mode to be used must be decided before installation.
With extraction-air mode, the air is discharged out of the house by a pipe (duct) to be provided by the installer.
When recirculation mode is chosen, the air is purified and discharged into the house through two rows of holes on the adjustable decorative cover.
Note: No attached ducting is needed for recirculation mode, but the activated charcoal or carbon filters must be installed to filter the air. In this mode, the suction power may be slightly lower.

WALL DRILLING AND BRACKET FIXING

NOTE: The safety gap between the range hood and the hob below must comply with the recommendations of the hob manufacturer. In case of no instructions, a minimum distance of 650mm (or other minimum distance as may be specified by AS/NZS 5601 and interpreted by a certified installer) should apply.

As a first step, proceed with the following drawings:

• A vertical line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted.
• A horizontal line A at 970 ­ 1070 mm above the cooker top. A horizontal line B at a X mm above the horizontal line A.
• A horizontal line C at 243 mm below horizontal line A.

Mark Points:

• Mark a point (1) on the horizontal line A, 80 mm to the vertical reference line.
• Repeat this operation on the other side and on the vertical reference line, checking that the three marks are leveled.
• Mark a point (2) on the horizontal line B, 60 mm to the vertical reference line.
• Repeat this operation on the other side, checking that the two marks are on the same horizontal line.
• Mark a point (3) on the horizontal line C, mm to the vertical reference line. Repeat this operation on the other side, checking that the two marks are leveled.

Fix the brackets:

• Drill holes at the marked points with a 10 mm drill bit.
• Insert the Wall Plugs 11 into the holes.
• Fix the hood fixing bracket 20 with 3 screws 10 (5 x 50) at the horizontal line A.
• Fix a Chimney fixing bracket 21 with 2 screws 10 (5 x 50) at the horizontal line B.

Lower decorative chimney

• Fix the 150mm diameter smooth wall rigid exhaust pipe (not supplied) on the hood body, connect chimney and hood body with 2 screws 12. connect chimney fixing bracket and chimney with 2 screws 12.

Hook the hood body

• Hook the hood body to bracket 20.
• Level the hood body itself.
• Remove the filter from the inside of the hood body, fix the screws 10 to Wall Plugs 11 at the points (3).

CONNECTIONS

DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the range hood to the chimney using a smooth wall rigid 150mm diameter ducting pipe (not supplied).

• Fix the pipe in position using sufficient pipe clamps (not supplied).
• Remove possible charcoal filters.

Upper Decorative Chimney

• Insert the upper decorative chimney into the lower decorative chimney and drag it up to the horizontal line
• Connect upper decorative chimney and chimney fixing bracket with 2 screws.

USE

Speed adjustment buttons
Each function is controlled independently by a button.

• When first plugged into a powered electrical socket, the rangehood will chime once to show it’s connected to the electrical supply. After the connection:
• Press the Power button to control the motor power. In Standby mode, pressing this button will cause the motor to operate at a low speed and the lights on the Power and Low-speed buttons will be illuminated. If the range hood is operating when the Power button is pressed the appliance will enter a 3 minute delayed Shutdown mode. Press the Power button again to turn the range hood off immediately.
• When the range hood is operating use the Low, Mid, and High buttons to select the speed. The motor will then operate at the selected speed and the light for that button will be illuminated to indicate the speed. If the range hood is already operating at the selected speed pressing this button has no effect.
• Use the Power button to turn off the rangehood. With one press the appliance will enter Shutdown mode and turn off automatically after 3 minutes. Press the Power button again to turn the range hood off immediately.
• Pressing the Low, Mid or High buttons during Shutdown mode cancels the Shutdown mode and the rangehood will operate at the selected speed.
• Press the Light button once to turn the lights on. Press it again to turn them off.

MAINTENANCE

FILTERS
Your Kleenmaid rangehood has one or both the following types of filters:

1. The visible aluminum grease filters, which are present on every rangehood.
CLEANING THE GREASE FILTERS

• These filters must be cleaned after every 2 months of operation, or more frequently for particularly heavy usage.
• Operate the latch on the grease filters and remove the filters one by one, pushing them towards the backside of the range hood unit and simultaneously pulling downwards.
• These filters may be cleaned either with a soft-bristled brush in warm soapy water or in a dishwasher (without other items).
• Any kind of bending of the filters should be avoided when washing them. Before fitting them back into the range hood make sure that they are completely dry. (The color of the filter surface may change over time but this has no effect on filter efficiency).
• When fitting the filters into the rangehood make sure that they are mounted in the correct position with the handle facing outwards, and latch securely.
• There is a fire risk if cleaning is not carried out in accordance with the instructions.

Normally these filters will last the life of the rangehood, however, if they are damaged in any way, replacements may be purchased by emailing support@kleenmaid.com.au or calling 02 9310 1207.

2. The internal Kleenmaid Activated Charcoal (or “Carbon”) Filter, which will be present on a rangehood installed in recirculating mode i.e. not vented outdoors.

These filters are located inside the rangehood and remove cooking odors from the air. They cannot be cleaned and will require replacement. The effective life of the filter depends on the type and amount of cooking you do. Generally, the life of these filters is approximately six months. However, always replace the filter when it no longer absorbs odors effectively.
When replacement Activated Charcoal filters are required they may be purchased by visiting the Kleenmaid website www.kleenmaid.com.au, emailing support@kleenmaid.com.au, or calling 02 93101207.

REPLACING THE ACTIVATED CHARCOAL FILTERS

• Remove the metal grease filters
• Remove the saturated activated charcoal filter.
• Fit the new filters.
• Replace the metal grease filters.

Warning: It must be ensured that the filters are correctly installed whenever the range hood is operating. Failure to do so may damage the range hood, and such damage will not be covered by the manufacturer’s warranty.

CLEANING THE RANGEHOOD

Clean the range hood regularly using a damp cloth and a neutral liquid detergent.
Switch off or unplug the appliance from the main supply before carrying out any maintenance work.

LIGHTING
LIGHT REPLACEMENT (Completed by professionals)
Replacing the light modules

• The light bulbs cannot be replaced. The entire light module has to be replaced.
• When changing the light modules, the contacts are live.
• Before changing the light module(s), unplug the appliance from the mains or switch off the circuit breaker in the fuse box.
• Remove the grease filter and carefully remove the 2 screws from the front plate (a Philips head screwdriver will be needed to remove the screws).
• Disconnect the terminal of the LED light.
• Press the LED light on the back of the front plate, take the LED light out.
• Replace the lamp(commercially available LED lamp (max.1.5w).

| Max Power| Voltage|  Picture| Lamp Cap| ILOCOS D code
---|---|---|---|---|---
Round/ Diameter
: 70mm| 1.5W| DC 12 V| | —| DSR-1.5-S-70

• Press the LED light on the front of the front plate, and install the LED light on the front plate.
• Connect the terminal of LED light and light leads.
• Carefully fasten the 2 screws on the front plate, and reinstall the grease filter.

TROUBLESHOOTING

blades.
The capacitor is damaged.| Contact Service Department
The motor is damaged.| Contact Service Department
The internal wiring of the motor is cut off/ disconnected. An unpleasant smell may be produced.| Contact Service Department
Both light and motor do not work| Apart from the above-mentioned, check the following:
Light damaged.| Replace lights.
The power cord is loose.| Contact Service Department
Oil leakage| The outlet and the air ventilation entrance are not tightly sealed.| Seal the duct connection with the appropriate sealant.
Vibration| The blade, if damaged, can cause vibrating.| Contact Service Department
The motor is not tightly fastened.| Contact Service Department
The range hood is not tightly fixed.| Fix the rangehood tightly.
Insufficient suction| The distance between the range-hood and the cooktop is too large.| Readjust the distance. according to installation instructions.
Too much ventilation from open doors or windows.| Choose a new place to install the appliance or close some doors I windows.
The
appliance inclines| The fixing screws are not tight enough.| Tighten the fixing screw and make it horizontal.
The hanging screws are not tight enough| Tighten the hanging screw and make it horizontal.

KLEENMAID WARRANTY

TERMS AND CONDITIONS

1. Compass Capital Services Pty Ltd ABN 96 138 214 525 trading as Kleenmaid will provide parts and labor to you the customer as set out herein.

2. Kleenmaid’s Products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
   You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does
   not amount to a major failure.

3. The benefits given to you under this Kleenmaid Warranty are in addition to other rights and remedies to which you may be
   entitled under the Australian Consumer Law in relation to the Product to which this Kleenmaid Warranty relates. Subject to
   the conditions below, the Product is warranted by Kleenmaid and/or its agents to be free from defects in materials and workmanship for the Warranty Period for normal Domestic Use.

4. Product Identification:
   a. Kleenmaid reserves the right to reject claims for any services or work where you cannot produce for verification the serial number and proof of purchase for the Product (including but not limited to the original invoice).
   b. this Kleenmaid Warranty will be voided if the serial number for the Product cannot be verified. This is not intended to exclude, restrict or modify any right or remedy to which you may otherwise be entitled under the consumer guarantee provisions of the Australian Consumer Law. c. in the event that a request for repair is made against this Kleenmaid Warranty where the serial number for the Product cannot be verified or you cannot produce for verification proof of purchase for the Product (including but not limited to the original invoice), the repairer will not carry out any repairs on the Product and you will be charged a service call-out fee.

5. What is covered by this Kleenmaid Warranty:
   a. the Product is covered for faulty workmanship or parts that have failed under normal Domestic Use.
   b. Kleenmaid and/or its agents will determine by objective testing if there are any defects in the Product and/or faulty workmanship.
   c. this Kleenmaid Warranty is only applicable if repairs on Products are carried out within Mainland Australia.
   d. this Kleenmaid Warranty:
   i. covers a Product purchased as new, manufactured for use in Mainland Australia;
   ii. commences from the date of delivery of the Product;
   iii. provides for the labor and replacement parts necessary to maintain the Product in good operating condition as specified in this Kleenmaid Warranty, however, if repair is needed because of a Product failure during normal Domestic Use, Kleenmaid has the option to repair or replace the defective Product or part of the Product with a product or part of like kind and quality. A replacement part may be new or reconditioned of like kind and quality and may cost less than the original Product is purchased and no charges or refunds will be made based on the replacement product or part cost difference; and
   iv. is only applicable when the Product is used and operated in accordance with the Manufacturer’s instructions.

6. What is not covered by this Kleenmaid Warranty (excluded):
   a. any damage or failure to or of the Product or part of the Product:
   i. due to the Product being inadequately serviced to manufacturer’s recommendations;
   ii. resulting from environmental conditions including and not limited to dirt, dust, rodents, insects, rust, corrosion, salt built-up, of or in any part of the Product;
   iii. resulting from excessive use but fair wear and tear is excepted;
   iv. resulting from poor installation including and not limited to positioning and externally fitted equipment such as plumbing and drainage, cabling, antennae or due to incompatibility of connected equipment;
   v. caused by overheating as a result of sitting or positioning of the Product, where there is no provision for adequate ventilation or adequate protection from excessive dust;
   vi. if the Product has been dismantled, repaired or serviced by any person other than someone authorized by Kleenmaid or its agents or representatives;
   vii. caused by power surges or spikes, including and not limited to, mains power and telecommunications connections, or to other unspecified sources, incorrect power current, voltage fluctuation, amperage fluctuation, rust or corrosion;
   viii. if the Product is dropped, the collision of the Product with another object, use for which the Product is not designed, damage to the Product caused by your own negligence, accidental or deliberate misuse of the Product by you, theft, abuse, vandalism, flood, fire, earthquake, electrical storms or any other act of God or any war-related events; or
   ix. due to the introduction of abnormal heat loads to the Product;
   b. costs of attendance and testing where no fault or defect covered by the terms of this Kleenmaid Warranty is identified in the Product;
   c. initial setup and installation of the Product;
   d. normal maintenance costs and costs incurred through the installation of items listed as requiring periodic replacement;
   e. Products with removed or altered serial numbers;
   f. broken or cracked glass other than transport damage to the initial point of delivery;
   g. consumables such as but not limited to bulbs/globes, seals, filters, batteries, and remote controls;
   h. removal and reinstallation of an internal component not performed by an authorized Kleenmaid agent or representative or authorized service center;
   i. cosmetic or structural items; or
   j. any failures due to interference from or with other products and/or sources.

7. This Kleenmaid Warranty ceases if:
   a. the Product ceases to carry the original manufacturer’s serial number or is sold at an auction;
   b. the Product is rented, or
   c. there is failure to pay monies owing on invoices as a result of non- warranty work being carried out at the request of the end-user as per point 16 below.

8. Neither Kleenmaid nor its representatives provide loan equipment under the terms of this Kleenmaid Warranty.

9. Any unauthorized access to the internal hardware of the Product will void this Kleenmaid Warranty.

10. Repair Notice: Products presented for repair may be replaced by refurbished products of the same type rather than being repaired. Refurbished parts may be used to repair the Products.

11. Replacement items are “like for like” and is not “new for old” and do not indicate in any way that a faulty Product will be replaced with a new part or unit. “Like for like” may either be a quality checked, refurbished or reconditioned unit of the same or later batch of model/size/specifications

12. The cost of making a claim under this Kleenmaid Warranty is not covered by Kleenmaid, including any costs of transportation or travel expenses between your home and your nearest authorized service agent.

13. Kleenmaid accepts no liability for items that are lost, damaged, or stolen as a result of freight, transport or storage. If you are required to transport the Product to an authorized service center, you must ensure that it is securely packed and insured.

14. On Public Holidays or other periods when regular business and wholesale operations are temporarily ceased, repairer availability and warranty response times may extend beyond the standard response times due to the unavailability of repairers and parts.

15. For any repair performed on a Product under this Kleenmaid Warranty where no fault can be found, or the item is deemed by Kleenmaid or an authorized agent, to be not faulty under this Kleenmaid Warranty, or the repair or fault is not covered under this Kleenmaid Warranty, a ‘No-Fault Found’ fee is payable by you. Kleenmaid will advise you of this cost and seek your agreement to pay such costs before commencing such repairs.

16. Any repairs or services required that are outside the terms and conditions of this Kleenmaid Warranty can be carried out at your request at your cost (including where the Product has not been installed or set up correctly). Kleenmaid will always advise you of this cost and seek your agreement to pay such costs before commencing such repairs. A credit card may be required prior to the commencement of such services.

17. Extra charges will be payable by the customer should the Product not be readily accessible without special equipment, such as but not limited to cranes and lifts or should the Product be installed in a position where service access is blocked and/or repair work is not possible without uninstalling the Product to gain access.

18. You, the customer, may be entitled to purchase an extended warranty in respect of the Product. Any extended warranty will not be issued by Kleenmaid but by a third party. Any extended warranty services will be provided directly by the third party as principal and not as an agent for Kleenmaid, under their extended warranty terms and conditions and not under this Kleenmaid Warranty.

19. To make a claim under this Kleenmaid Warranty, please have your proof of purchase and the serial number of the Product ready and call (02) 9310 1207 during business hours.

20. This Kleenmaid Warranty is given by: Name: Compass Capital Services Pty Ltd ABN 96 138 214 525 trading as Kleenmaid Business address: Level 2, Suite 3, 204 Botany Rd, Alexandria NSW Australia 2015 Telephone: (02) 9310 1207

21. Definitions:
    a. Australian Consumer Law means the Competition and Consumer Act 2010 (Cth).
    b. Domestic Use means the use of the Product for personal, domestic or household purposes.
    c. Kleenmaid means Compass Capital Services Pty Ltd ABN 96 138 214 525 trading as Kleenmaid.
    d. Mainland Australia means the following States and Territories of Australia: New South Wales, Victoria, South Australia, Western Australia, Queensland, Tasmania, Northern Territory, and Australian Capital Territory.
    e. Product means the appliance sold by Kleenmaid to you as evidenced by the original purchase invoice.
    f. Warranty Period means the period of 60 months for domestic use, 12 months for non-domestic use or such alternative period as may be specified.

UPDATE NOTICE: This Kleenmaid Warranty is current as at 1 January 2019 but is subject to variation from time to time.
For the latest version of the Kleenmaid Warranty, please see our website
http://www.kleenmaid-appliances.com.au/support/your-kleenmaid-warranty or phone us on (02) 9310 1207.

Other products available in the Kleenmaid range of appliances

• Washing machines
• Clothes dryers
• Dishwashers
• Ovens
• Cooktops
• Steam ovens
• Microwave ovens Built-in espresso coffee machines
• RangehoodsFreestanding ovens
• Refrigerators & Freezers
• Beverage Serving Cabinets
• Water Dispensers Vacuum
• Cleaners

To register your warranty or make a warranty claim, scan this QR code:

http://www.kleenmaidwarranty.com.au/

Compass Capital Services Pty Limited trading as Kleenmaid ABN 96138214525

Level 2, 204 Botany Road Alexandria NSW 2015

Register your Kleenmaid Appliances Warranty
www.kleenmaidwarranty.com.au
Request a Warranty Service
www.kleenmaidwarranty.com.au

E: support@kleenmaid.com.au
Please download the current User Manual for this appliance at www.kleenmaid.com.au

References

• Kleenmaid Warranty Assistance

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>