Schneider Electric NSX400-630 Extended Rotary Handle Owner’s Manual

: June 9, 2024
: Schneider Electric

ComPacT™ NSX400-630 – PowerPacT™ L-Frame

www.se.com

ComPacT NSX100–630| ComPacT NSX DC
DOCA0187EN| DOCA0186EN

www.se.com/support

NSX400-630 Extended Rotary Handle

Retain instruction sheet for future use. Visit our website at www.se.com to download the documents listed above (user guides ) and other documents.
PLEASE NOTE

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.
All pertinent state, regional, and local safety regulations must be observed when installing and using this product.

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA Z462, NOM-029-STPS or local equivalent.
This equipment must only be installed and serviced by qualified electrical personnel.
Turn off all power supplying this equipment before working on or inside equipment.
Always use a properly rated voltage sensing device to confirm power is off.
Put back all devices, doors, and covers before turning on power to this equipment.
Beware of potential hazards, and carefully inspect the work area for tools and objects that may have been left inside the equipment.

Failure to follow these instructions will result in death or serious injury.

Required for Installation

Before Working on Equipment

Turn off all power supplying this equipment before working on or inside equipment.
Turn off device before installation.
Use a properly rated voltage sensing device to confirm power is off.

Rotary Handle Adaptation

Wiring Routing

Early-break Contact

https://download.schneider-electric.com/files?p_Doc_Ref=GHD16294AA

To install the early-break contact, consult the instruction sheet GHD16294AA.

Early-make Contact

https://download.schneider-electric.com/files?p_Doc_Ref=GHD16307AA

To install the early-make contact, consult the instruction sheet GHD16307AA.

Rotary Handle Keylock Adapter

https://download.schneider-electric.com/files?p_Doc_Ref=GHD16293AA

To install the rotary handle keylock adapter, consult the instruction sheet GHD16293AA.

Handle Adaptation

Activation of Locking in I-On Position

When the rotary handle is locked in I-On position:

the protection functions are still active and will trip the circuit breaker in case of electrical fault
the user can trip the circuit breaker in case of emergency with the push-to-trip button.

Deactivation of Door Interlock in I-On and Trip Position

The rotary handle is delivered with the door lock activated.
To deactivate door locking when the handle is in the I-On or Trip position:

Turn and hold the rotary handle in the O-Off position.
Tighten the screw inside the handle to the specified torque value.

Installation

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Install the device rotary handle before energizing device to prevent access to live terminals.
Failure to follow these instructions will result in death or serious injury.

NOTICE
HAZARD OF EQUIPMENT DAMAGE

Be careful not to pinch electrical wires when installing the rotary handle.
Tighten all rotary handle screws to stated torque.
Do not over torque screws.
Do not use power equipment to torque screws.

Failure to follow these instructions can result in equipment damage.

Front-Panel Cutout

Use the GVAPL01 laser tool for precise drilling of the cutout on the door.

Trimming the Shaft

Fixed or Plug-in Device with Fixed or Telescopic Shaft

Withdrawable Device with Telescopic Shaft

Mounting the Handle

Operation

Device Status

Device Operation

Close Device

Reset After a Trip
CAUTION
HAZARD OF CLOSING ON ELECTRICAL FAULT
Do not close the device without first inspecting and, if necessary, repairing the downstream electrical equipment.
Failure to follow these instructions can result in injury or equipment damage.

| | |
---|---|---|---
Device has tripped.| Reset the device.| Inspect and repair downstream equipment, using proper safety precautions.| Close the device.

Device Operation with Door Open

https://download.schneider-electric.com/files?p_Doc_Ref=EAV78496

To operate the circuit breaker when the door is open, use an open door shaft operator LV426937.
Consult the instruction sheet EAV78496.

Locking the Handle

Locking in O-Off Position

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
When device rotary handle is locked in O-Off position, always use a properly rated voltage sensing device to confirm power is off before working on equipment. Failure to follow these instructions will result in death or serious injury.

Locking in I-On Position

To activate locking of handle in I-On position, consult the section 4.1.

Door L4ocking in I-On and Trip Position

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
The rotary handle is delivered with the door lock activated.
When the door lock is activated, only qualified persons are authorized to disable the door lock.
Failure to follow these instructions will result in death or serious injury.
To deactivate the door Interlock in I-On or Trip position, refer to section 4.2.

Sealing

https://download.schneider-electric.com/files?p_Doc_Ref=GHD16296AA

To install the sealing accessory, consult the instruction sheet GHD16296AA.

Manufacturing Date

The product’s manufacture date is coded PP-YYYY-Www-D, where:

PP: plant code
YYYY: year of manufacture
Www: week of manufacture
D: weekday of manufacture (Monday = 1)

Eg: 7Q-2019-W20-3 = product manufactured at plant 7Q on Wednesday 15 May 2019

Schneider Electric Industries SAS
35, rue Joseph Monier
CS 30323
F – 92506 Rueil Malmaison Cedex
www.se.com
NNZ4766507-02
© 2022 Schneider Electric – All rights reserved.

Schneider Electric Limited
Stafford Park 5
Telford, TF3 3BL
United Kingdom
www.se.com/uk