T I P TECHNIK KOMPETENZ SBS 36 Solar Watering Set Instruction Manual

T I P TECHNIK KOMPETENZ SBS 36 Solar Watering Set

General safety instructions

Please read through these usage instructions carefully and familiarise yourself with the controls and proper procedures for using this product. We are not liable for damage that occurs due to a failure to observe instructions and rules given in these usage instructions. Damage that occurs due to a failure to observe instructions and rules given in these usage instructions does not fall under the guarantee. Keep these usage instructions in good condition and enclose them when transferring ownership.

Persons not conversant with the contents of these operating instructions must not use this device. The pump must not be used by children. The pump may be used by persons with reduced physical, sensory or mental capabilities or lack of experience and/or knowledge if they have been supervised or instructed in the safe use of the equipment and have understood the resulting hazards. Children are not allowed to play with the device. Keep the appliance and its cord out of reach of children. Disconnect the device from the power supply and let it cool down before cleaning and maintenance is performed and before the device is stored. Check the device for transport damage. If there is damage the retailer must be notified without delay, at the latest however, within 8 days of the purchase date.

Safety measures

Prior to use:

• Check the connection cables and plugs for damage.
• The operating voltage and current type must match the specifications on the type plate.
• Important! If there is damage to the connection cables, the devices are unusable and must be disposed of. Repair is not possible because the connecting lines are permanently cast.
• Do not subject the control housing to any dull blows.

Application areas This product is a DC solar pump that has been developed for use in water tanks. The collector operates the pump and charges the battery by converting the sunlight that is absorbed into energy. The pump’s solar mode can be  used in virtually all weathers, regardless of whether the sun is shining strongly or it is cloudy. If the energy that is absorbed is insufficient to operate the pump, it is operated via battery This device has been developed for private use and not for industrial or commercial purposes. This device has been developed for private use and not for industrial or commercial purposes. The pump is not suitable for displacement of salt water, faecal matter, flammable, corrosive or other hazardous liquids. The pumped liquid must not exceed the maximum temperature specified in the technical data.

Technical data

Scope of delivery

Assembly/disassembly Important! The pump must not run dry. Otherwise, the possibility of damage to the device cannot be ruled out!
The numbers specified in the following text refer to figures I and II at the end of the operating manual.

• Unpack all components carefully.

• Affix the control unit (1) using the above-lying mounting holes. Make sure that the control unit is attached at a suitable location, above the water surface and protected from strong weather conditions.

• Affix the ground spike to the solar collector’s frame side (2). We recommend securing the ground spike to the long sides of the collector for stability reasons.

• Press the ground spike with the collector installed on it into a soft substrate such as grass.

• Point the collector surface to the south and ensure that the surface is not in the shadows.

• Connect the solar collector (2) to the right connection ( ) of the control unit.

• Now connect the filter (3) to the control unit at the left connection ( ).

• Cut off your desired length (approx. 1 m) of hose (4) — for installation as a suction hose — and plug it with one side on the connection for in-flowing water (IN) (control unit) and with the other side on the connection to the filter (3).

• Now cut off about 15 cm of the accompanying hose (4) and plug it with one side on the connection to the control unit for out-flowing water (OUT) and the other side on the connection of a T-fitting (5).

• Now, using the suction cups, place the filter (3) in the side of your water container as far as possible beneath the water surface — but somewhat above the floor so that no dirt or other sediment can be sucked in.

• Cut off about 10 cm of the hose (4) and plug it onto one side of a T connection (5).

• On the other end of the piece of hose (4), plug the check valve (8). Make sure that the “OUT” marking on the check valve (8) points to the hose (4). This prevents water running uncontrollably when the pump stops.
  NOTE: The check valve must always be higher than the water level!

• Plug the hose (4) onto the last free side.

• The hose (4) can be freely cut according to your needs and the drip outlets (7) can be installed entirely individually.

• Disconnect the hose (4) at any point and install one of the T connections in between (5).

• Cut off a piece of hose (4) and plug it onto a T connection (5).

• Lastly, put the drip outlet (7) onto the end of the hose piece (4).

• Repeat this until all necessary drop outlets (7) are handled.

• Arrange the drip outlets (7) individually on your plants according to your needs and fix them in place using the attached hose holders (6).

• If the end is not equipped with a drop outlet, seal it with the enclosed sealing plugs (9).

• Now the solar watering set is ready for use and can be used.

• Never connect the pump to a mains plug, it is only designed for 6 V DC battery operation.

Placing in service

• Comply with the safety measures! Never short circuit the battery that is integrated into both poles in the control housing! The device’s connection cables must not be damaged!
• The batteries must be completely charged before switching on the device. In addition, the solar-powered device must be charged in direct sunlight for a minimum of 4 hours after installation. The pump must not be switched on during the initial charging process. Make sure that there are no shadows on the solar panel, otherwise the charging capacity will be greatly reduced. If the device has not been operated for a long period of time, repeat the measures described above.
• Low battery: If the battery is empty, the solar panel must be charged in direct sunlight for at least 4 hours and watering must not be switched on frequently.

Overview status display

• LED lights up green: The pump is switched on.
• LED flashes green: The pump is off. Battery needs to be charged.
• LED flashes red: Lack of water and/or battery empty.
• LED flashes red & green: Lack of water and battery is charging.

Timer indicator| Mode| Function| LED indicator lamp| |
---|---|---|---|---|---
“T”

position

| Test| Watering switches on automatically when the battery is empty| The green indicator lamp lights up|
“0”

position

| Stop watering| Stop watering| The green indicator lamp switches off|
“1”

position

| 30 seconds operation| Watering takes place twice a day for 30 seconds| The green indicator lamp lights up|
“2”

position

| 1 minute operation| Watering takes place twice a day for 1 minute| The green indicator lamp lights up|
“3”

position

| 2 minutes operation| Watering takes place twice a day for 2 minutes| The green indicator lamp lights up|
“4”

position

| 4 minutes operation| Watering takes place twice a day for 4 minutes| The green indicator lamp lights up|
1| Water level indicator|
“5”

position

| 8 minutes operation| Watering takes place twice a day for 8 minutes| The green indicator lamp lights up|
2| LED indicator lamp|
“6”

position

| 12 minutes operation| Watering takes place twice a day for 12 minutes| The green indicator lamp lights up| 3| Solar panel socket|
4| Timer indicator|

Maintenance and care

• Solar collector: The solar collector must be cleaned regularly with a soft cloth. Regular cleaning is recommended to guarantee that the sunlight is absorbed and converted into energy in an optimum manner.
• Pump: If the pump’s flow rate reduces after a certain time or the pump no longer works at all, check whether sediment, sludge or other dirt is in the filter.
• Maintenance intervals The time intervals for the required maintenance task (complete cleaning) to a great extent are based on Water contamination. Select the time intervals for cleaning accordingly. If, when performing maintenance tasks, you determine that there are defects or wear, replace the parts in question (see ordering spare parts).
• Maintenance in winter Protect your device from freezing! Please remove the device in autumn/winter and empty it completely. We recommend charging the batteries fully before shutting down the device for a longer period of time (e.g. over the winter). For this purpose, the device should be charged for several hours in direct sunlight without switching on the device. This charging procedure should be repeated at least every 3 months while the device is shut down. Make sure that the device is switched off during the winter so the battery is not discharged. During the winter, store the device in a heated room in order to slow down the battery’s self-discharging process.

Troubleshooting/recommendations

• In operation, water runs from the check valve
  • The check valve has been mounted the wrong way round. Turn in over and put it on the other way round.
• Water the drip outlets without the pump running
  • Check the return value for continuity and check the mounting direction.
• LED in the control device does not light up
  • Is the solar module plugged in? Battery empty, wait for sunshine.
• The system flashes and no watering takes place
  • Check the water level in the water barrel. Check the water level sensor cable for integrity and whether the connector is inserted securely into the control device.
• No water comes out of the rear drip outlets during watering
  • Remove the drip outlets from the line and unscrew them. Then check whether the rubber membrane is sitting properly in the holder.
• The watering system does not water in the morning and in the evening
  • Check whether the solar module is inserted into the socket properly. If this is not the case, then please change the position of the module.

Guarantee

The present device was manufactured and inspected according to the latest methods. The seller warrants for faultless material and workmanship in accordance with the legal regulations of the country in which the device was purchased. The warranty period begins with the day of the purchase and is subject to the provisions below: Within the period of warranty, all defects which are to be attributable to defective materials or manufacturing will be eliminated free of charge. Any complaints are to be reported immediately upon their detection.

The warranty claim becomes void in the case of interventions undertaken by the purchaser or by third parties. Damage resulting from improper handling or operation, incorrect setting-up or storage, inappropriate connection or installation or Acts of God or other external influences are excluded from warranty.

Parts being subject to wear and tear, such as the pump wheel (impeller) and mechanical shaft seals are excluded from warranty. All parts were manufactured using maximum care and high-quality materials and are designed for a long lifecycle. It should be understood, however, that the wear and tear depends on the kind of use, the intensity of use and the internals of maintenance. Complying with the installation and maintenance information contained in the present operating instructions will therefore considerably contribute to a long lifecycle of these wearing parts.

In case of complaints, we reserve the option of repairing or replacing the defective parts or replace the entire device. Replaced parts will pass into our property.
Claims for liquidated damages are excluded unless they are caused by wilful acts or negligence on the side of the manufacturer.

The warranty does not provide for any claims beyond those referred to above. The warranty claim has to be evidenced by the purchaser in the form of the submission of the sales receipt. The present warranty commitment is valid in the country in which the device was purchased.

Please note:

• Should your device fail to function properly, please verify first whether an operating error or another cause is present which cannot be attributed to a defect of the device.
• In case you have to take or send in your defective device for repair, please be sure to enclose the following documents:
  • Sales receipt (sales slip).
  • A description of the occurring defect (a description as accurate as possible will expedite the repair work).

Ordering spare parts

The quickest, easiest and best value avenue for ordering spare parts is online. Our website www.tip-pumpen.de has a convenient spare parts shop, allowing you to order with just a few clicks. In addition, we use it to provide comprehensive information and valuable tips on our products and accessories, introduce new devices, and present the latest trends and innovations in the pump technology sector.

Service

For guarantee claims or faults, please contact: A current operating manual is available as required as a PDF file via e-mail: service@tip- pumpen.de.

Disposal and recycling of packaging The device is in packaging designed to prevent transport damage. This packaging is raw material and can therefore be reused. However, since special transport regulations apply to devices with lithium-ion batteries, the original packaging should be retained throughout the entire service life of the device, for possible transport or shipping. After this, it can be fed back into the raw material cycle.

Disposal of the device If the device must be disposed of, please ensure that it is completely discharged. Lithium-ion batteries are hazardous waste and are marked with the crossed-out wheeled bin symbol. The symbol indicates to end users that batteries should not be disposed of with household waste but should be collected separately. Used batteries can be returned free of charge to the point of sale, the recycling centre or the retailer’s disposal system.
To prevent short circuits and the associated heating, lithium-ion batteries must never be stored or transported unprotected in bulk. Appropriate measures must be taken to prevent short circuits.

For EU countries only Do not dispose of your electrical devices with household waste! In accordance with European Directive 2012/19/EU, which relates to used electrical and electronic devices as well as the relevant implementation in domestic law, used electrical devices must be separated out, collected, and sent for environmentally friendly recycling. Should you have any questions, please contact your local disposal company.

References

• Start - Pospischil - Reparaturbonus
• Start - Pospischil - Reparaturbonus

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>