anko 43233885 True Wireless Noise Cancelling Earphones User Manual
- June 9, 2024
- Anko
Table of Contents
anko 43233885 True Wireless Noise Cancelling Earphones
Product Overview
CAUTION: The battery in this product is not replaceable.
- The battery cannot be subjected to high or low extreme temperatures, or low air pressure at high altitudes during use, storage, or transportation.
- Disposal of a battery into a fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
WARNING
Do not dispose of the unit in fire or water. Never attempt to disassemble and
reassemble. Waste electrical products should not be disposed of with household
waste, please recycle where facilities exist.» Check with your local authority
for recycling advice. » Keep your device and all accessories out of the reach
of children and animals.> Small parts may cause choking or serious injury if
swallowed. Avoid exposing your device to very cold or very hot temperatures
(below 0’C or above 40°C). > Extreme temperatures can cause deforming of the
device and reduce the charging capacity and life of your device. > Do not
allow your device to get wet-liquids can cause serious damage. Do not handle
your device with wet hands.
Before first use
Unpacking
- Remove all packaging
- Remove the sticker on the charging contact point
- Please keep the packaging. The appliance can be stored in it if not used for a longer period of time.
Charge
This appliance is powered by a built-in rechargeable battery. So the Charging
Case and the earbuds are needed to be fully charged before first use.
Charge the Case
- Connect the USB-C charge cable to the socket on the charging case.
- Plug the cable into a standard USB 5V/500mA output.
- The LCD screen on the case will show the battery charging status while the case is charging and will show 100% status when fully charged.
- When fully charged, unplug the charging cable.
Notice: The USB-C (Type-C) power source for the apparatus shall not exceed 5V 3A.
Charging the Earphones
-
Put the Earphones into the charging case. The LCD screen will show “L” and “R”, indicating that the Earphones are placed correctly in the case.
-
Close the charging case lid. The Earphones LED indicator will stay red while the Earphones are charging. When charging is complete the LED will turn OFF.
(Note: the Earphones come with a built-in rechargeable battery. Before using them for the first time, we recommend you fully charge the battery. A full charge takes approximately 2 hours.) -
The case LCD screen will show the Earphones’ battery status when the Earphones are placed into the case correctly.
WARNING: The Earphones can only be used with the provided charging case. -
Now the appliance is ready for use.
How to use these earphones
Power On
Make sure the earbuds and your device are next to each other (within 3 feet
1 meter).
Option 1
Open the charging Case and take the earbuds out, the earbuds will power on
automatically.
Option 2
When the earbuds are not in the case and in power-off status, touch and hold
the touchpad for 2 seconds to power on.
Pairing the Earphones with Bluetooth devices
-
Go to Bluetooth settings on your Bluetooth device (phone, tablet, etc.)
-
Turn the Bluetooth ON, on your device.
-
Open the charging case and remove the Earphones, they will automatically turn on (or can be turned on manually). When the LED indicator on one side earphone flashes red and blue alternately, while the other side flashes blue, pair the earphones with your device.
Tip: When there is no earphone flashing red and blue alternately, place the earphones back into the case and take them out again. -
Select the pairing name of your Earphones on the list of available devices.
The pairing name is KM43233885. -
The Earphone LED indicator will flash blue once every 5 seconds when connected.
Functions
Music
- Play/Pause Tap the earphones of either earphone once
- Next Two touch the touchpad of the Left (L) earphone
- The previous two touch the touchpad of the Right (R) earphone
Phone Calls
- Accept/End a call Tap the touchpad of either earphone once
- Reject Call Tap the touchpad for 2 seconds
- Redial last call Tap the touchpad of either earphone 3 times
Active Noise Cancelling & Transparent
Long press the touchpad for about 2 seconds, then the Transparent mode and
ANC ON/OFF mode of the earphones are replaced alternately as you need. The
Active Noise Cancelling feature will electronically mute background noise. It
can be used to enhance the quality of any music or audio that is playing
through the earbuds. Transparent Mode enables the earbuds to pick up external
sounds, so you can stay aware of your surroundings.
Power Off
Option 1
Place the earbuds back into the case to automatically power
off.
Option 2
Touch and hold the touchpad for 4 seconds to power off the earphones, and the
red indicator light will be on for 2 seconds.
Option 3
If there is no connection with a wireless device within 3 minutes after
powering on, the earbuds will automatically power off.
Troubleshooting
Problem
|
Possible cause
|
Solution
---|---|---
The appliance does not work.| The appliance is out of power.| Charge the
appliance (refer to the section “charging the appliance”).
Wireless connection cannot be established or poor music playback/phone calls.|
Out of detection range. Transmission conditions are not optimal (for example
thick walls).| Move closer to the wireless device (less than 10 meters).
Remove/bypass obstacles, and check the wireless setting of the device to be
paired.
No Sound.| The wireless device is muted or the volume is too low.| Readjust
the wireless device volume.
Specifications
- Model No.: 43233885
- Version: Bluetooth V5.3
- Support profiles: A2DP, HFP
- Frequency response: 20Hz ~ 20kHz
- Impedance: 32 Ohm
- Drive size: 10mm
- Sensitivity: 105dB±5dB
- Working distance: 10 meters
- Earbud battery capacity: 2 x 40mAh
- Charging case battery capacity: 260mAh
- Earbud charging time: approx. 2 hours
- Charging case’s charging time: 2 – 3 hours
- Charging voltage: 5V DC
- Music time: 4 hours
- Talk time: 3 hours
- Standby time: 25 hours
12-month warranty
Thank you for !cJOUr purchase from Kmart.
Kmart Australia Ltd warrants your new product to be free from defects in materials and workmanship for the period stated above, from the date of purchase, provided that the product is used in accordance with the accompanying recommendations or instructions where provided. This warranty is in addition to your rights under Australian Consumer Law.
Kmart will provide l::lOU with your choice of a refund, repair, or exchange (where possible) for this product if it becomes defective within the warranty period. Kmart will bear the reasonable expense of claiming the warranty. This warranty will no longer appll::l where the defect is a result of alteration, accident, misuse, abuse, or neglect.
Please retain your receipt as proof of purchase and contact our Customer Service Centre on 1800 124125 (Australia) or 0800 945 995 (New Zealand) or alternatively, via Customer Help at kmart.com.au for any difficulties with your product. Warranty claims and claims for expenses incurred in returning this product can be addressed to our Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure For New Zealand customers, this warranty is in addition to statutory rights observed under New Zealand legislation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>