PHILIPS SRP4050 Replacement Remote User Manual
- June 4, 2024
- Philips
Table of Contents
PHILIPS SRP4050 Replacement Remote
Introduction
The TV replacement remote RRC has preprogrammed the most updated IR code and
is ready to use.
Your replacement remote
Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome
Insert batteries (not included)
Warning
Check the battery polarity when inserting in the battery compartment. Incorrect polarity may damage the product.
Caution
- Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire.
- Risk of decreased battery life! Never mix different brands or types of batteries.
Note
When you replace the batteries, all user settings will be retained in the memory of the universal remote for 5 minutes.
Manual set up by code selection
The replacement remote RRC has preprogrammed the most updated IR code and is ready to use. If it does not work, you can manually select the code from our list that can fit your TV.
Set up by code selection
- Switch on your TV.
- Press and hold 1 and 6 at the same time for 5 seconds until the red LED is on
- Look up the available 5-digit code. The most popular code is listed first. The factory default code is 0 0 0 0 0.
- Enter the selected 5-digit code using the digit buttons.
- If the light is off, a valid code is saved. Otherwise, the light will flash six times, and then remains on for code re-entry
List of IR code for Hisense TV
Auto IR code search
- Turn off your TV with stand-by power
- Press and hold 1 and 6 at the same time for 5 seconds until the red LED is on.
- While pointing at your TV with the RRC, press and release the PLAY button once, it sends Power On/Off command of an IR code from our list
- When the TV turn on (it might takes a few seconds for some TV to power on),you can try other keys (except PLAY and STOP) to see if the TV response.
- You can press STOP to confirm and exit the search. If most of the other keys does not work properly, turn off your TV and press PLAY again to try the next code.
Code Learning
You must have an original remote for the Replacement Remote Control (RRC) to
learn code from it.
Learn commands
- Press and hold 1 and 6 at the same time for 5 seconds until the red LED is on.
- Enter the learning code 9 9 9 0 0 . The red LED light will flash once and then remains on.
- Place the RRC and the original remote, head to head aiming at each other, on a flat surface.
- On the RRC, press the button that you would like to learn a code from the original remote. The LED will flash twice and stay on.
- On the original remote, press and hold the button that you would like to learn from for 2 seconds.
- The LED will blink once and stay on if the learning was successful. To learn another key, repeat Step 4. To exit, press 1 and 6 at the same time.
- The LED will blink 6 times quickly if learning failed. Repeat Step 4 to learn again.
Clear learned commands
- Clear all codes learned for the replacement remote control
- Press and hold 1 and 6 at the same time for 5 seconds until the red LED is on.
- Enter the learning code 9 9 9 1 0 . The red LED light will remain on briefly, flash twice and then turns off.
- All codes learned for the replacement remote control will be cleared.
Disposal of your old product and battery
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains batteries covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. Inform yourself about the local separate collection system for electrical and electronic products and batteries. Follow local rules and never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries helps prevent negative consequences for the environment and human health. Removing the disposable batteries To remove the disposable batteries, see section ‘Insert batteries’. When this logo is attached to a product, it means a financial contribution has been paid to the associated national recovery and recycling system.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Frequently asked questions
- My replacement remote does not work at all.
- Check if you have correctly setup the device with the right code. Check if you have pressed the corresponding device key for your device.
- Check if the batteries are inserted properly. If the battery level is low, replace the batteries.
- Check if your device is powered on.
If several device codes are listed under the brand of my device, how can I
select the correct device code?
To seek the correct device code, test the codes one by one. The codes are
sorted by popularity, and the most popular code is listed first.
My device responds only to some of the commands.
You have set a code for which only some commands work properly but some do not. Try other codes until most keys work properly or learn the key from original remote if it support learning function.
Need help?
We advise you to first read this user manual carefully. It helps you set up and use the replacement remote. If, however, you require extra information or have additional questions about setup, usage, warranty, etc of the RRC, you can always contact us. When calling our helpline, make sure to have the RRC at hand when you call, so that our operators can help you determine whether RRC is working properly. You will find our contact details at the end of this user manual. For online support, visit www.philips.com/support
Specifications are subject to change without notice.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke
Philips N.V. and are used under license. This product has been manufactured by
and is sold under the responsibility of MMD Hong Kong Holding Limited or one
of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in
relation to this product. SRP4000_10_UM_V1.0
P Vision Europe B.V.
- Prins Bernhardplein 200 1097 JB Amsterdam The Netherlands Authorised Representative
- UKCA Experts Ltd.
- Dept 302, 43 Owston Road Carcroft Doncaster, DN6 8DA United Kingdom
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>