HyperX HX430C15FB3/8 8GB 1G x 64-Bit DDR4-3000 CL15 288-Pin DIMM Memory Module User Guide
- June 9, 2024
- HYPERX
Table of Contents
HX430C15FB3/8 8GB 1G x 64-Bit
DDR4-3000 CL15 288-Pin DIMM Memory Module
User Guide 
Memory Module Specifications
HX430C15FB3/8
8GB 1G x 64-Bit DDR4-3000 CL15 288-Pin DIMM
DESCRIPTION
HyperX HX430C15FB3/8 is a 1G x 64-bit (8GB) DDR4-3000 CL15 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 1G x 8-bit FBGA components per module. Each module kit supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. Each module has been tested to run at DDR4-3000 at a low latency timing of 15-17-17 at 1.35V. The SPDs are programmed to JEDEC standard latency DDR4-2400 timing of 17-17-17 at 1.2V. Each 288-pin DIMM uses gold contact fingers. The JEDEC standard electrical and mechanical specifications are as follows:
FACTORY TIMING PARAMETERS
- Default (JEDEC):………….DDR4-2400 CL17-17-17 @1.2V
- XMP Profile #1:…………..DDR4-3000 CL15-17-17 @1.35V
- XMP Profile #2:………… DDR4-2666 CL15-17-17 @1.35V
SPECIFICATIONS
| CL(IDD) | 17 cycles |
|---|---|
| Row Cycle Time (tRCmin) | 45.75ns(min.) |
Refresh to Active/Refresh
Command Time (tRFCmin)| 350ns(min.)
Row Active Time (tRASmin)| 32ns(min.)
UL Rating| 94 V – 0
Operating Temperature| 0°C C to +85°
Storage Temperature| -55°C to +100°C
FEATURES
- Power Supply: VDD = 1.2V Typical
- VDDQ = 1.2V Typical
- VPP = 2.5V Typical
- VDDSPD = 2.2V to 3.6V
- On-Die termination (ODT)
- 16 internal banks; 4 groups of 4 banks each
- Bi-Directional Differential Data Strobe
- 8 bit pre-fetch
- Burst Length (BL) switch on-the-fly BL8 or BC4(Burst Chop)
- Height 1.3425″ (34.1mm), w/heatsink
MODULE WITH HEAT SPREADER
MODULE DIMENSIONS
All measurements are in millimeters.
(Tolerances on all dimensions are ±0.12 unless otherwise specified)
The product images shown are for illustration purposes only and
may not be an exact representation of the product.
Kingston reserves the right to change any information at anytime without
notice.
FOR MORE INFORMATION, GO TO HYPERXGAMING.COM
All Kingston products are tested to meet our published specifications. Some
motherboards or system configurations may not operate at the published HyperX
memory speeds and timing settings. Kingston does not recommend that any user
attempt to run their computers faster than the published speed. Overclocking
or modifying your system timing may result in damage to computer components.
HyperX is a division of Kingston.
©2019 Kingston Technology Corporation, 17600 Newhope Street, Fountain Valley,
CA 92708 USA.
All rights reserved. All trademarks and registered trademarks are the property
of their respective owners.
Document No. 4809080A
hyperxgaming.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>