ANDERIC RRHC100 TV Remote Control Instruction Manual

ANDERIC RRHC100 TV Remote Control Instruction Manual

Introduction

We want to thank you for purchasing this Universal Hospitality remote by Anderic®. With the purchase of this remote, you should receive a screw for the battery cover. Battery cover screw is optional; the battery cover does not need the screw to hold it in place. This remote requires two AAA size batteries, not included.

Optional Security Cable Attachment

Optional Security Cable available from anderic.com, Part number: CBL01. This cable easily adheres under the battery cover for a secure and flush appearance.

Pre-programmed Codes

This remote is pre-programmed by default to LG and VIZIO TVs under TV mode and DirecTv under STB Mode (Set-Top-Box). If the TV or STB is not one of the brands.
above, you must program the remote using the directions below:
NOTE: If [S] key is not present on your remote, note that it is the unmarked button to the right of the [POWER] key.

Programming the remote: Direct Code Input Method

1. Turn on the device you want to control, and find the corresponding brand code from the attached code list.
2. Press and release the device mode key you would like to program ( [TV] or [STB] ).
3. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
4. Input the four digits If the remote successfully saved the code, the indicator light will go out. If error, the indicator light will blink slowly three times and go out, repeat steps 1-4.
5. Check if most keys of remote control can control the device, if not, please restart steps 1-4 using a different code.
6. After trying all codes for your brand without success, please try the “ Programming the remote – Code Search ” method below.

Note: During the programming mode, pressing any button other than number buttons or not pressing any button for 10 seconds will cause the remote to exit programming mode.

Programming the remote: Code Search Method

Note: use this method if your brand is not listed in the codes attached, or if all the codes you tried do not work. This method scans through each code in the database.

Manual search

1. Turn on the device you want to
2. Press and release the device mode key you would like to program ( [TV] or [STB] ).
3. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
4. Repeatedly Press [CH+] to search forwards or [CH-] to search backward; remote will send the code of POWER one by one.
5. When the device is turned off, immediately press the [S] button to save and exit. Check if most keys of remote can control the device, if not, please restart from step 1, remote will pick up where it left off in the code database.

Auto search

1. Turn on the device you want to
2. Press and release the device mode key you would like to program ( [TV] or [STB] ).
3. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
4. Press and release [POWER] key, mode indicator light will blink one time and continue to blink every 2 Remote is sending codes of POWER one by one. If to press [CH+] / [CH-] can change the searching direction.
5. When the device is turned off, immediately press the [S] button to save and exit. Check if most keys of remote can control the device, if not, please restart from step 1, remote will pick up where it left off in the code database.

Code Display

About: use this method to display the code that is currently programmed.

1. Press and release the device mode key ( [TV] or [STB] ) in which you want to display programmed code, then follow the steps below:
2. Press and release keys [MUTE] and [1] simultaneously, then release. The indicator light flashing times represent the first digit of the code. Note: If the digit is 0, the indicator light will not flash.
3. Press and release keys [MUTE] and [2] simultaneously, then The indicator light flashing times represent the second digit of the code.
4. Press and release keys [MUTE] and [3] simultaneously, then The indicator light flashing times represent the third digit of the code.
5. Press and release keys [MUTE] and [4] simultaneously, then The indicator light flashing times represent the fourth digit of the code.

Note: If the digit is 0, the indicator light will not flash.

Single Press Combined POWER Key

About: This allows for powering on/off both your TV and STB (Set-top-box) with one press of the [POWER] button. If enabled, pressing the [POWER] key will send code for power for both units. If disabled, pressing the [POWER] key will only send code for TV. See the steps below.

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Device mode indicator light will light. It doesn’t matter which mode lights. Input code [ 9] [9] [9] [5].
3. Enabled – (0 blinks): If the indicator light turns off directly after inputting the four digits, this indicates that “one key power-off all devices” was successfully enabled;
4. Disabled – (2 blinks): If the indicator light blinks 2 times after inputting the four digits, this indicates that “one key power-off all devices” was successfully disabled.

Note: After one key power-off all devices successfully enabled , press [POWER] key, it will send STB Power immediately followed by TV Power code.

STB (set-top-box) Punch-Through Function

About: When enabled, this feature allows assigning the STB-related keys to always send codes programmed under STB mode, no matter what mode the remote currently resides. This feature has been enabled by default. Keys affected are 0 thru 9, Enter, Prev CH, CC, CH+, and CH-.
Follow the steps below to enable or disable this feature.

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Device mode indicator light will light. It doesn’t matter which mode lights. Input code [ 9] [9] [9] [0].
3. Enabled – (0 blinks): If the indicator light turns off directly after inputting the four digits, this indicates that “STB punch-through” was successfully enabled ;
4. Disabled – (2 blinks): If the indicator light blinks 2 times after inputting the four digits; this indicates that “STB punch-through” was successfully disabled.

TV Punch-Through Function

About: When enabled, this feature allows assigning all TV-related keys to always send codes programmed under TV mode, no matter what mode the remote currently resides. This feature has been enabled by default. The keys affected are Power, VOL+, VOL-, Mute, Input, and Sleep. Follow the steps below to enable or disable this feature.

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Device mode indicator light will light. It doesn’t matter which mode lights. Input code [ 9] [9] [9] [1].
3. Enabled – (0 blinks): If the indicator light turns off directly after inputting the four digits, this indicates that “TV punch-through” was successfully enabled ;
4. Disabled – (2 blinks): If the indicator light blinks 2 times after inputting the four digits; this indicates that “TV punch-through” was successfully disabled.

Individually assign key punch-through Lock

Note: _Before proceeding; the following features must be first DISABLED: “ TV Punch-through Function ,” “ STB punch-through Function ,” and “ Single Press Combined Power Key.” _Applicable to all buttons except for: [S], [TV], [STB]. To re-assign a key to a different mode, you first unlock the key using steps from the Individually Assign Punch-through Unlock section below, then repeat steps 1-4 to reassign it to the correct mode.

About: This allows for individually assigning keys to “punch-through” to the mode of your choosing. After enabling punch-through, the key will always send code for assigned mode no matter what mode the remote currently resides.

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Input the 2 digits code [9] [8].
3. Press the button you want to lock.
4. Press the device mode button you want to assign it to (e.g. [ TV] or [STB] ). If successful, the indicator light will turn off directly after pressing the Mode button. Repeat steps 1 – 4 for each button lock.

Individually Assign Punch-through Unlock

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Input the three digits [ 9] [0] [0] ,
3. Press the button you want to unlock the punch-through, the indicator light will blink one time & turn off.

Device Mode Lock

About: This is used to lock the code for the device so it cannot be re- programmed. After the device is locked, the current code cannot be changed, and any other operation is invalid unless you repeat steps 1-3 to unlock first.

1. Press and release the device mode key you would like to lock code for ([TV] or [STB] ).
2. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
3. Input code [ 9] [9] [9] [9] ,
4. Locked – If the indicator light turns off directly after 4 digits input, it indicates mode successfully locked.
5. Unlocked – If the indicator light blinks 2 times and turns off after 4 digits input, it indicates mode successfully

Reset to Factory Default Status – Unchanging 1-Device/2-Device Status

Note: This restores remote to factory default status while keeping the currently programmed

1-Device or 2-Device mode.

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Input code [ 9] [9] [9] [6]. The indicator light will turn off, indicating that the remote has been reset to factory default status.

Reset to Factory Default Status

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Input code [ 9] [7] [6] [0]. The indicator light will turn off, indicating that the remote has been reset to factory default status.

Advanced Option: Shift remote to 1-Device; TV only remote.

Note: This feature allows the remote to switch from a 2-Device remote to a 1-Device; TV only remote. STB mode will be deactivated. Remote will be reset to factory defaults for 1-Device.

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Input code [ 9] [7] [6] [1]. The indicator light will blink 3 times, indicating that the remote has successfully been reset to factory default status and converted to a 1-Device remote.

Advanced Option: Shift remote to 2-Device; TV/STB remote.

Note: This feature allows the remote to switch from a 1-Device remote to a 2-Device; TV and STB enabled remote. Both modes will be activated. Remote will be reset to factory defaults for 2-Device.

1. Press and hold [S] and [ENTER] keys simultaneously for about three seconds until the indicator light lights and remains on, release both keys.
2. Input code [ 9] [7] [6] [2]. The indicator light will blink 3 times, indicating that the remote has successfully been reset to factory default status and converted to a 2-Device remote.

LEGAL: Anderic® is a registered trademark of Dan’s Electronics Etc., Inc. All rights reserved. This document is copyrighted.

TV CODES

Note: The following codes can be programmed under TV mode only.

LG Hospitality Codes

Note: The following codes work with LG STB-2000 set to boxes and can be programmed under TV or STB mode.

Digital TV Converter Box Codes

Note: The following codes can be programmed under STB mode only.

Cable Box Codes

Note: The following codes can be programmed under STB mode only.

SAT/DTV/WEBTV Box Codes

Note: The following codes can be programmed under STB mode only.

Programming/Function Codes

COMBINED POWER 9995
STB PUNCH-THROUGH 9990
TV PUNCH-THROUGH 9991
INDIVIDUAL PUNCH-THROUGH 98 [key to assign] [mode to assign to
(TV)/(STB)] INDIVIDUAL KEY UNLOCK 900 _
DEVICE MODE LOCK 9999
RESET TO 1-DEVICE MODE 9761
RESET TO 2-DEVICE MODE 9762
RESET TO FACTORY 9760

Read More About This Manual & Download PDF:

References

• Anderic Official Site | Home | North Carolina

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>