ELITE SCREENS VMAX 2 Series Electric Motorized Projection Screen User Guide
- June 9, 2024
- ELITE SCREENS
Table of Contents
VMAX 2 Series Electric Motorized Projection Screen
User Guide
Electric Motorized Projection Screen
VMAX 2 Series
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedure below.
Caution: The screen’s Black Top Drop is already set to its maximum drop
distance. There is NO extra Black
Top Drop in the roller. Please be aware of this as it will void your warranty
with Elite Screens. Unapproved changes or modifications (except for cutting
the power cord for hardwire installations) to this unit are prohibited and
will void your warranty. For more information, please contact our Technical
Support Department at 877-511-1211 Ext.
604.
- Please retain this user’s guide for future reference.
- To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the manufacturer.
- Handle the unit carefully during transportation to avoid any damages.
- To ensure safe and reliable operation, direct connection to a properly grounded power source is advised.
- The power outlet supplying power to the unit should be close to the unit and easily accessible.
- Do not install the unit on uneven or inclined surfaces.
- Do not put heavy objects on the power cord and position it properly to avoid creating a trip obstacle.
- Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short circuit.
- There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself. No one except authorized technicians can open and make repairs to this unit.
- Make sure the power source this unit is connected to has a continuous power flow.
- If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to avoid overheat.
- Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
- Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
- Avoid direct Sunshine, rain shower and moisture.
- Keep away from fire sources and high temperature to prevent this device from overheating.
- Cut off the power supply first before transportation or maintenance.
- Fully disconnect from the power supply when the unit is not in use for a long period of time, as should be done with any other electric household appliance.
- To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious damage or if there are any evident broken parts.
Installation Warning
Due to various installation environments, the instructions provided in this
user’s guide are for reference only. Please consult a professional
installation company for further installation and safety advice. The
installer must insure that proper mounting hardware is used to provide
adequate strength suitable for the installation. Elite Screens is not liable
for any faulty installations.
The Screen’s Top Black Drop is already set to its maximum drop distance. There
is NO extra top black drop in the roller. Please be aware of this as it will
void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the
warranty with the manufacturer. Please contact Elite Screens Customer Service
for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a
particular installation. If this equipment causes harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
Reorient or relocate the receiving antenna of the device which may be casing
the interference.
Increase the separation between the screen and the device’s receiver.
Connect the equipment into a different power outlet other than the device.
Pre-Installation
- Carefully unpack the screen.
- Always handle the screen in a leveled position on a clean surface.
- In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles such as dust, sawdust, and/or liquids.
NOTE:
Regardless of the mounting method, the screen should be securely supported so
that the vibration or pulling on the viewing surface will not cause the casing
to become loose or fall. The installer must insure that the fasteners used
are of adequate strength and suitable for the installation location.
Accessories for VMAX 2 Series
Please make sure all accessories below are included before proceeding.
Control System for VMAX 2 Series
- 5-12V Trigger: The built-in 5-12V trigger input allows your screen to synchronize its drop & rise with the projector’s power cycle. The screen deploys when the projector powers up and will retract when the projector powers down. The 5-12 volt adaptor connects to your projector’s trigger output via a separate cable that may or may not be provided by the manufacturer of the projector. The trigger feature will not work without an output cable from the projector, but it can be tested by connecting the Red (+) and Green (-) cable to a 9-volt battery.
- 3 -Way Wall Switch: The 3-way wall switch is a wall mount control box with an up/stop/down button and plugs directly into the screen’s RJ-45 input.
- IR “Eye” Receiver: The IR “Eye” Receiver plugs directly into the screen’s RJ-45 input to present a low profile line- of-sight control option for your IR remote control even in a recessed ceiling installation.
- IR Remote Control: The Infrared functions by direct line of sight contact with a beam range of 30 feet.
- RF Remote Control: The radio waves eliminate the need for a direct line of sight with a range of 150 feet.
Installation Instructions
Please consult a professional installer. Elite Screens is not liable for any faulty installations.
- Select the installation location for your screen within reasonable proximity from your power source.
- For best support of your screen, it is ideal to secure your screen into the studs of your house’s internal framework. If studs are not available, use hollow anchors for mounting your wall screws into drywall. If you’re installing in a concrete structure, use concrete bolts to secure your screen. Always consult a professional installer or hardware professional to ensure that the proper screws and/or hardware are being used.
- Ensure that both brackets are in perfect level alignment with one another. Use wall/ceiling wood screws to secure to the wood studs. Use hollow anchors if mounting in drywall.
- The screen casing is designed to accept the wall screws directly. If not using the Optional L-Brackets http://shop.elitescreens.com/accessories.aspx, be sure to position the washer between the head of the walls crew and the anchor slots on the screen’s casing.
- Using a tape measure, mark the keyholes that are located at the back of the screen’s casing end cap.
- After marking the area and predrilled hole, insert the screw and have at least 1/8” from the wall to mount the screen. (See example in Figure 1.)
- Figure 2 will show you an optional installation using chains (not included).
Optional installation method using a chain to hang the screen from the ceiling
For more information, technical support or your local Elite Screens
contact, please visit www.elitescreens.com
Rev. 051117 DR
www.elitescreens.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>