HKS 43005-AN004 Super Fire Racing Coil Pro Instruction Manual

SUPER FIRE RACING COIL PRO
INSTRUCTION MANUAL
43005-AN004 43005-AN005

MANUAL
NUMBER| E05341-N20010-00
PART NUMBER| 43005-AN004| 43005-AN005
APPLICATION| NISSAN SILVIA(E-KPS13, E-PS13, E-S14, E-CS14) NISSAN 180sx(E-RPS1I E-KPS13)| NISSAN SILVIA(GF-S15)
ENGINE| SR2ODET can not be installed except for vehicles equipped with SR2ODET. ),.(If the installed engine is replaced, it matches the actually installed engine. Please select the product you want. If the engine has been replaced, make sure that the harness has also been replaced.
REMARKS| -This instruction manual is for using F-CON V Pro 3.4 for the ECU. When using other ECUs, please refer to the instruction manual of the ECU to be used for installation and setting.
This Product was designed by a JDM vehicle and has not been tested with another market model yet.
•After installing this product, the genuine plug cover cannot be installed. Do not allow the ignition coil to be exposed to rain or water directly. Use with HKS spark plug is recommended.

REVISION OF MANUAL

NOTICE
This manual assumes that you have and know to use the tools san equipment necessary to safety perform service operations on your vehicle.
This manual assumes that you are familiar with typical automotive systems and basic service and repair Procedures. Do not attempt to carry out the operations shown in this manual unless these assumptions are correct. Always have access to a factory repair manual. To avoid injury, follow the safety precautions contained in the factory repair manual.
IN REGARD TO MANUAL AND PRODUCT

• This manual indicates items that require careful attention in order to install this Product safely, and lists precautions to avoid any possible damage and/or accidents.
• This Product was designed for and tested on a factory-spec vehicle or a vehicle equipped with other HKS Products. Performance and/or safety cannot be guaranteed if this Product is installed onto other inapplicable vehicles.
• HKS will not be held responsible for any damage caused by faulty installation, or mishandling, nor for damages caused by modifications to or dismantling of this Product.
• This specification of this Product are subject to change without notice.
• This manual is subject to be revised without notice
• This Product is designed for use in Japan only. It must not be used in any other country.

SAFTY INSTRUCTIONS

Warning Indicates risk of serious injury and/or possible death.
Caution Indicates risk of serious injury or property damage.

Parts List

 Installation

Caution

• Be sure to perform the work according to the service manual and the instructions issued by the manufacturer.

1. Disconnect the cable terminal from the negative terminal of the battery.

2. Remove the genuine timing belt cover, ignition coil harness, and ignition coil.

3. For vehicles with S13 and S14 engines, remove the power transistor. (Figure 1) Then attach the power transistor conversion harness. Insert it firmly until the connector clicks.
   

4. Attach the flanged bolt (M6 x 40) and hexagonal high nut to the coil bracket. (Figure 2) (Tightening torque 11.3±1.2 N・m)
   

5.  Fix the hexagonal column to the engine head. (Figure 3) (Tightening torque 5.1±0.5N・m)
   

6. Apply silicone grease to the O-RING and attach it to the coil spacer. (Figure 4)Then attach it to the engine head. At this time, attach it straight to the engine head.
   If it is not installed properly, the waterproof effect will be impaired.

7. Temporarily tighten the coil bracket from the bracket fixing hexagonal support bolt, and then fix it with the bracket fixing bolt (M5 x 15) so that the bracket can be attached horizontally little by little. (Figure. 5) (Tightening torque 3.5±0.3N・m)

8. Secure the ignition coil with a flanged hex nut. (Figure. 6) (Tightening torque 7.0±0.7N・m)

9. Attach the ignition coil harness to the ignition coil and the engine harness of the vehicle body. The one with the shortest harness is the bulkhead side of the vehicle. Firmly until the connector clicks Please plug it in. Secure the harness with a tie wrap. (Figure 7)

10. Ground the ground wire of the ignition coil harness at a place where it can be reliably grounded. (Figure. 8) The recommended grounding position for HKS is the wiper motor mounting part shown in the photo. Depending on the vehicle, it may be painted, so remove the paint or extend the ground wire. Also, fix the ignition coil harness using the attached tie wrap so that it does not touch the exhaust manifold. Caution
    If the ignition coil harness is incompletely grounded, it may lead to a misfire, etc., and the original performance of the ignition coil cannot be exhibited. Do not go to the engine head, but to a place where the vehicle can be reliably grounded.
    When grounding to the negative side of the battery, it is necessary to extend the harness, but use a splice or the like to extend it. Also, since wiring is done near the exhaust manifold, be sure to fix it as well.
    Check that each harness is not pulled excessively and that each connector is securely inserted all the way.

11. Make sure that the installation work is correct, and then install the negative terminal of the battery.

Dwell Time (Recommendation) & F-CON setting

Caution

• Be sure to set the dwell time with a specialist and check that the engine is properly controlled. There is a risk of misfire.
• Do not set a value greater than the recommended dwell time. The ignition coil may be damaged.

1. Set the IG signal voltage of the engine ECU to 5V.
   For an ECU whose IG signal voltage cannot be adjusted, check with the manufacturer of the ECU to see what V control the signal voltage is. Those that are not controlled by 5V cannot be used.

2.  Set the dwell time (energization time) for each engine speed by referring to the recommended values below. Caution
   Set the dwell time according to the specifications and characteristics of each engine.

The recommended dwell time (energization time) for each power supply voltage is as follows. (Reference rotation speed 3600 rpm, reference voltage 13 V)

The checklist before starting the engine

Make sure all installed components and harnesses do not come in contact with other parts.|
Make sure two 0-RINGs are attached.|
Make sure there are no tools in the engine room.|
Make sure to reconnect the negative cable onto the battery.|
Make sure that all bolts and nuts are tightened.|

Caution

• Use without setting may lead to engine damage/failure.
•  Incomplete installation of connectors/harnesses may indicate the check engine light.

The checklist after starting the engine

Make sure all installed components and harnesses do not come in contact with other parts.|
Make sure harness is not strongly twisted.|
Make sure are not made interference sounds.|

Caution

• To be routed the harness away from any other parts such as the hood, sharp edges, and pipes, etc.

Troubleshooting

Off this Product is not working properly, check the list below and take necessary measures.

・Engine does not start
・Unstable idling| Spark plugs did not completely installed.
The coil is not inserted properly.
The harness is not connected.
The plug is passed its lifespan.
Grounding Issue.| ・Make sure connector
・Make sure plug and ignition coil
・Check engine ground.
Misfire under high rpm, heavy load.| The plug is not inserted properly.
The coil is not inserted properly.
The plug is passed its lifespan.| ・Make sure connector
・Make sure plug and ignition coil

If the above guidelines don’t solve the issue, please contact an HKS authorized dealer/distributor in your area.

Operation

Warning

• If the vehicle gets damaged, have the repairs performed by a professional.
• If you experience any abnormal noises, scents, or vibrations from the vehicle while driving, reference the factory service manual.
• In case of an accident or another issue, do not try to solve the issue and contact HKS authorized dealer/distributor.
• If you experience any abnormal noises, scents, or vibrations from the vehicle while driving, reference the factory service manual.

After-sales service

For inquiries about this Product, please contact a Professional dealer or the store where you purchased the Product.

Contractor|
---|---
Phone number|
Person in charge name|
Customer name|

HKS Co., Ltd
7181 Kitayama, Fujinomiya,
Shizuoka 418-0192, JAPAN
http://www.hks-power.co.jp/en/

Documents / Resources

| HKS 43005-AN004 Super Fire Racing Coil Pro [pdf] Instruction Manual
E05341-N20010-00, 43005-AN004, 43005-AN005, Super Fire Racing Coil Pro, 43005-AN004 Super Fire Racing Coil Pro
---|---

References

• HKS Co., Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>