HKS DS095192 Hi-Power SPEC-LⅡ Finisher Cover Instruction Manual

June 4, 2024
HKS

HKS DS095192 Hi-Power SPEC-LⅡ Finisher Cover

Installation Manual

This product is an optional Finisher Cover for HKS Hi-Power SPEC-L II.

After you confirm the product application,please read this document in order to use this product safely and to make it fully function.
After installation, always have access to a factory service manual for future maintenance.

Safety Precautions

  • The following precautions for use of this product are to prevent possible accidents and/or injuries and for proper use.
  • This manual describes the precautions you need to follow in order to install this product safely and to prevent danger and damage to customers and third parties


Warning

| Indicates risk of serious injury and/or possible death.
---|---


Caution

| Indicates risk of damage to people or large-scale damage to property. (Large-scale damage is the damage caused by a product defect.ex. Damage to a vehicle,fire,etc.)


Advice

| Indicates an advice for correct product installation.

  • HKS is not liable for any damages that customer or third parties may receive from installation and/or use of this product and the accessories.

Please pass this document to a customer.
(Please keep this manual in a safe place)


TO CUSTOMER:

Product Precautions

Caution

  • Do not use this product for any vehicle other than specified in the manual. It may damage the vehicle and lead to an accident.
  • Do not dissasemble or modify this product.
  • Stop using the product if any unusual situation is noticed. Consult with the dealer immediately. Failure to do so may cause damage to a vehicle or lead to an accident.
  • Daily maintenance of the vehicle including after the installation of the product, to keep the vehicle properly performing is the responsibility of the owner.
  • If due to aging or damage, the vehicle is unable to perform as it was originally intended, perform a vehicle inspection as soon as possible.

Installation Precautions

Warning

  • To avoid injury, follow the manual instruction during the installation.

Caution

  • To avoid injury, stop the engine and make sure the exhaust system has completely cooled down. Always use protective gear such as glasses when working on the vehicle.

Advice

  • A greasy and dirty exhaust and Finisher Cover will make a correct installation difficult. Clean and wipe the items before starting the installation.
  • Please use an authorised profesional shop for installation.

Tools Required For Installation

  • Hex Wrench 2.5mm
  • Threadlock adhesive (HKS recommends using Loctite Threadlocker 243)
  • Heat Gun or Dryer
  • Replacement gasket for exhaust

Parts List(Please verify the contents before the installation)

  • Finisher Cover x 1
  • Bolt (M4) x 3
  • Installation Manual

Installation Instructions

  1. Remove an exhaust from a vehicle.
  2. Remove a currently attached exhaust tail tip from the exhaust.
  3. The Finisher Cover is attached with bolts using a threadlocker adhesive, use a heat gun to soften threadlocker adhesive, then remove bolts. Apply heat ONLY from the inside of the Finisher Cover.
  4. Slide on an optional Finisher Cover, so that it comes to the correct position.
  5. Use a threadlocker adhesive with three provided bolts (M4) to fix the optional Finisher Cover. Make sure to keep the tip cover straight and carefully tighten the bolts to a specified torque. Specified Torque : M4 T= 1.2 N・m (T= 0.12 kgf・m) ]
  6. If the Finisher Cover is inclined or not fixed straight, untight the bolts sligthly, adjust the position and try again.
  7. Refer to a manual provided with the exhaust and attach the exhaust back to the vehicle.

Caution

  • If you apply heat to the outer surface of the Finisher Cover, it may cause color change.
  • Applying too much strength may damage the bolts.
  • Without a threadlocker adhesive, vibration and heat expansion may cause bolts to untighten and may lead to lost of Finisher Cover.
  • For use of threadlocker adhesive please refer to instruction manual of your threadlocker adhesive.

Parts Application

ø94 SHORT TYPE


34002-AK010| CARBON TIP
34002-AK013| TITAN TIP
34002-AK016| BLUE-SUS

ø94 LONG A-TYPE


34002-AK011| CARBON TIP
34002-AK014| TITAN TIP
34002-AK017|  BLUE-SUS

ø75 A-TYPE


34002-AK019| CARBON TIP
334002-AK020| TITAN TIP
34002-AK021|  BLUE-SUS

ø94 LONG B-TYPE


34002-AK019| CARBON TIP
334002-AK020| TITAN TIP
34002-AK021|  BLUE-SUS

HKS Co., Ltd.
7181 Kitayama, Fujinomiya,
Shizuoka 418-0192, JAPAN
http://www.hks-power.co.jp/en/

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals