GooDee BM001 5 Inch Baby LCD Monitor User Manual

: June 9, 2024
: GOODEE

GooDee BM001 5 Inch Baby LCD Monitor

GooDee BM001 5 Inch Baby LCD Monitor

Overview

Packing List

Monitor| | Camera|
---|---|---|---
AC Power Adapter x2| | Mount Kit|
Mounting Bracket| | Power Cable x2|
User Manual| | |

Camera

Night Vision Sensor
Camera Lens
IR LED
Microphone
Pair Button
Power Input
Temperature Sensor
Mounting Bracket
Speaker

Monitor

Power/Sleep Button: Long press to turn on/off the monitor; short press to turn on/off the screen.
Menu/Back: Press to enter menu page or press as a Back button.
Camera Switch: Switch cameras if connected with 2 or more cameras.
Charging Indicator: It gives off yellow light while the monitor is being charged.
Left: Press to pan the camera leftward orto change your selection leftward.
Up: Press to tilt the camera upward orto change your selection upward.
Right: Press to pan the camera rightward or to change your selection rightward.
Down: Press to tilt the camera downward orto change your selection downward.
Power Indicator: The green light turns on if connected to electricity.
Zoom/OK: Press to Zoom in/out or to confirm your selection.
Talk: Press to talk to your baby in the monitoring image.
Sound Level LED: Low/high level shows low/high sound detected by the camera.
Volume/Brightness: Press to adjust the monitor’s volume or brightness in the monitoring image
Microphone
15.Antenna
Battery Compartment
Support Stand
Speaker
Power Input
Reset Hole

Note:

If you RESET with a pin, the monitor will be forced shutdown.
Do not open the battery compartment without official guidance.

How to get started

Step 1:

Connect the camera to the AC adapter.
Plug the AC adapter into a socket.
Note: Put the camera away from your baby (3ft/1m away at least).

Step 2:

Connect the monitor to the AC adapter.
Plug the AC adapter into a socket.
Long press the Power button to turn on the monitor then you can see the monitoring interface.

Note:

The monitor takes about hours to be fully charged, and it lasts about 8-10 hours.

Function Operation

Camera(Add and Pair)

Notice:
The camera and monitor were paired already. This function is to add new cameras to the monitor.

Add cameras (How to pair)
Step 1:

Press to enter menu page.
Choose and press OK button.

Step 2:

Select then press OK button.

Step 3:

Select and press OK button TWICE. See Camera is NOT paired.
Press OK button to start pairing.

Step 4:

Press PAIR button on the back of the camera.
Then see the prompted Paired.
Note: Four cameras at most can be connected to one monitor.

Delete cameras
Step 1:

Press to enter menu page. Choose and press OK.
Select the camera need deleting. Press OK.

Step 2:

Press to enter menu page. Choose and press OK..
Select the camera need deleting. Press OK.

Step 2:

Select the right camera icon. Press OK TWICE
See Deleted. Your camera is deleted.

Sound Detection

Explanation:
There are four options of sound detection, LOW (78dB), MEDIUM (70dB) and HIGH (65dB). LOW means the sound can be detected if it reached 78dB, and so on for MEDIUM and HIGH.

VOX Mode:
The display screen enters the standby state, and the camera detection sound reaches 70dB. The display screen is on for one minute without alarm sound.

Step 1:

Press M~u to enter menu page. Choose and press OK.
Select the option you want. Press OK.

Temperature Alarm

Explanation:

indicates that the temperature value for high and low temperature alarms can be set.

Step 1:

Press to enter menu page. Choose and press OK.
Select the option you want. Press OK.

Language

Explanation:
There are eight languages built in our device, you can choose your language here.

Step 1:

Press to enter menu page. Choose and press OK.
Select your language and press OK to confirm.

Lullabies

Explanation:
This function is to comfort your baby when needed.

Step 1:

Press to enter menu page. Choose and press OK.
Select the lullaby you want. Select ALL to play the lullabies in a loop.

Sleep Mode

Explanation:
This function is to prolong your monitor’s runtime by shutting down the screen.
Step 1:

Press to enter menu page. Choose and press OK.
Select the time you want.

Note: The screen will automatically light up if there is a sound alarm or a temperature alarm.

Feeding

Explanation:
This function is to remind you of feeding your baby. OFF means you shut down the function; 2.5 hour means it reminds you every 2.5 hours and so on for the other options.

Step 1:

Press to enter menu page.
Choose and press OK.
Select the time you want.
Select OFF to turn off the feeding reminder.

Note: Selecting will set the alarm to the specified time.

Settings

Explanation :
This function is to set Date/Time, turn on/off OSD, restore factory settings and provide service support information.
Date/Time:

Press to enter menu page.
Choose and press OK.
Select Date/Time.
Press OK to enter the interface.
Press OK to start/finish setting. stands for starting the setting.
stands for finishing the setting.

Note:

Press Up/Down/Left/Right to select and press OK button to confirm.
If OSD is ON, the date and time will be displayed on the status bar of the monitor; otherwise, it will not be displayed.

Restore factory settings:

Select and conform
Press OK to enter the interface.
Conform YES to reset. Press or conform NO to exit.

Settings

Select .
Press OK to enter the interface.

ICONS EXPLANATION

Status Bar Icons
: No signal connection
: Signal strength
: Live video loop
: Lullabies enabled
: Sleep Mode enabled
: Current room temperature
: Battery Level
: Sound detection enabled
: Temperature alarm enabled
: Feeding reminder enabled
: 2 times magnification
: 4 times magnification
: Night mode
: VOX mode is on
Notifications Icons
: No camera connected
: Sound Alarm
: Temperature Alarm
: Feeding Notification

Explanation:
You can open Live-Video-Loop function through short presses on the button until you see r:i on the status bar. When Live-Video-Loop function is on, the connected cameras will automatically switch every 10 seconds. And if there is a sound/temperature alarm, the camera-switch function will pause temporarily.

Warning and Safety Instructions

Follow these safety precautions to prevent fire, injury or damage to the product and your baby. Read and keep instructions handy. It is very important to read all the safety and operation instructions before use.

Warnings:

Strangulation Hazard:
Children may be entangled in cords. Keep the monitor ,camera,and AC power cord out of reach of your baby and children at all times. At least 3 feet away.

Danger from power cords:

Danger from power cords: To avoid possible danger from power cords, the cords should be secured and never be hung on or near the crib. Never place the camera or monitor inside your baby’s crib, bed or playpen.

Water and moisture:
The product should not be exposed to rain, moisture, or splashing .Never use or place the product in or near moisture and water.

Ventilation:
This product shall not be used on a bed, sofa, rug, or similar surface that may block the ventilation or speaker openings, or be placed in an enclosed area, such as a bookcase or drawer that drawer that may impede air flow. Never cover the product with clothes, towels, blankets, or any other item.

Battery:
Before you use the product,we recommend you fully charge the battery of the monitor,so that it continues to work if you disconnect it from the power supply and carry it to another location. Transmission range: The range of all baby monitor is measured in open space.This actual range may be shortened due to environmental obstacles(such as the concrete walls). This product is not toy: It should be kept out of children’s reach.
Do not disassemble the product:
If you have any problems with the product,please contact the customer service team.In case of unusual noises of smells originating from the device,immediately disconnect the prouduct from power outlet and contact the customer service team.If the product becomes dirty,use a lightly damp soft cloth to wipe surfaces.Do not allow water into any openings.
Operation location:
The operating location plays an important role in ensuring proper operation.Maintain a distance of 5 feet from other electronic equipment,such as microwave ovens or Wi-Fi routers.Otherwise they may cause interference.If it occurs,move the camera and monitor to another location.
Important:
This baby monitor is an aid designed for hearing the baby’s voice and seeing the images of the baby. This product is not a medical device and should not be used as a substitute for responsible adult supervision. It is important that you regularly check on your baby personally.

Safety Instructions for AC Power Adapter

During continual use, the power adapters may become warm.This is normal and should not be a cause for concern.
Examine the intactness of the power cord and its plug before use.
he adapter must be handled with care.Do not handle it roughly,like a drop or throw.
When removing the power adapter from the wall outlet, hold and pull from the receptacle.
Do not pull on the cable itself as it will put additional stress on the cable and could lead to damage.
Do not touch the power adapter with wet hands or allow liquids to spill on it.
Do not put any objects on top of the power cord, which could cause overheating, damage, combustion ,and electrocution.
Do not leave the power adapter connected to the wall outlet when it is not plugged into the camera or monitor.

Maintenance and Warranty

Maintenance

All of the following maintenance procedures should only be performed when camera and monitor are unplugged and turned off.

Clean the surfaces of the camera and monitor with a soft,fluff-free cloth.
Never use cleaning agents or solvents .
If the units become dirty,use a slightly damp cloth to wipe surfaces.Take care not to allow water into any openings.

Warranty terms

This baby monitor comes with a one-year warranty (replace or refund) and lifetime technical support. The warranty terms do not apply to any product that has been subject to abuse, misuse, negligence, or accident.
If you have warranty or support issues, please contact the customer service of Amazon seller before leaving your review.
*Information on Product Disposal
Always dispose of your product (with a non-removable pre-installed battery) at the end of its life in an environmentally responsible way and in accordance with your local waste disposal requirements. All cardboard and paper packaging materials should be recycled in accordance with your local council waste regulations.

WARNING
Incorrect use of the product(s) may lead to safety risks. Therefore, we STRONGLY recommend reading the following instructions before using your product.

Keep the cord(s) away from children in case of strangulation (3 feet/ 1 meter away).
Put the product(s) in a dry place in case of short-circuit.
Use the AC adapter(s) provided by us ONLY. Using unauthorized charging cables and AC adapters may result in overheat even explosion.
Unplug the AC adapter(s) if you don’t use it(them).

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(l)this device may not cause harmful interference.
(2)this device must accept any interference received, including interference that may cause undesired operation.