ViewZ VZ-215LED-HDR 21.5 Inch Professional Video Monitor User Manual

ViewZ VZ-215LED-HDR 21.5 Inch Professional Video Monitor

Important Safety Instructions

The device has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the device should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.

• Please do not place the display screen towards the ground to avoid scratching the LCD surface.
• Please avoid heavy impact.
• Please do not use chemical solutions to clean this product. Simply wipe with a soft cloth to keep clean of the surface.
• Please do not place on uneven surfaces.
• Please do not store the monitor with sharp, metallic objects.
• Please follow the instructions and trouble-shooting to adjust the product. Internal adjustments or repairs must be performed by a qualified technician.
• Please keep user guide for future reference.
• Please unplug the power and remove the battery if long-term no-use, or thunder weather.

Safety Disposal For Old Electronic Equipment

Please do not regard the old electronic equipment as municipal waste and do not incinerate old electronic equipment. Instead please always follow local regulations and hand it over to the applicable collection stand for safe recycling. Ensure that these waste materials can be effectively disposed of and recycled to prevent our environment and families from negative effects.

Introduction

This monitor is wide field of vision is matched with excellent color space, which reproduced the colorful world with the most authentic elements.

Features

• HDMI1.4 supporting 4K 30Hz.
• 3G-SDI input & loop output.
• 1000cd/㎡ high brightness.
• 1920X1080 high resolution.
• Support multiple video input interfaces: SDI, HDMI, VGA, AV.
• FN User-definable function button.
• HDR supporting HDR10_300, HDR10_1000, HDR10_10000, HLG.
• Color Temperature (6500K, 7500K, 9300K, User).
• Markers & Aspect Mat (Pixel to pixel, Zoom, Aspect ).
• Scan (Full scan, Under scan, Over scan).
• Marker color (Red, Green, Blue, Mono).

Production Description

Front Panel

1. Power Button.

2. FN button, can be set by [Menu]-[System]-[FN Configuration].
   Default: [Level Meter]

3. EXIT Button.

4. Button: Press it to increase volume when power on; Select options downward in the menu.

5. Button: Press it to decrease volume when power on; Select options upward in the menu.

6. MENU Button: Press it to display the menu on the screen when power on. Press it to confirm the option selected.

7. INPUT Button: Switch among of AV, VGA, HDMI and SDI signals.

8. Brightness Sensor

9. Power Light (Red/Green).

Rear Panel

1. Power input: DC 12V.
2. Earphone input(3.5mm).
3. Audio input.
4. Video input.
5. VGA input.
6. HDMI 1.4 input.
7. USB 2.0 (for upgrade).
8. SDI output.
9. SDI input.
10. Speaker*2.

Supported Mounting Ways

• Desktop
  Standing on the table by installing the desktop bracket on the bottom of the monitor.
  

• Wall mount
  Installed and fixed on the standard VESA bracket through VESA 75mm holes on its rear panel.
  

Menu Settings

Before setting the functions, please make sure the device is connected correctly.

Shortcut Button

2-1-1. Menu Button

• Press MENU button, the menu will pop up on the screen. Then select item as the following sequences via pressing ****button: PICTURE / MARKER / FUCTION / VGA / AUDIO / SYSTEM. Press MENU button again to enter into the item you select.
• Press ****button to adjust options or values in the selected item. Then press MENU or EXIT button to apply and save the setting.
• When Menu is inactivated, press button to adjust volume. Then select item as the following sequences via pressing MENU button: Brightness / Contrast / Saturation / Tint / Sharpness and Exit. Press button again to adjust the value in the selected item.

FN Button

Press Menu button, select [System]-[FN Configuration] to set the FN button function. User can set the FN button function: Center Marker / Aspect Marker/ Check Field/ Display Scan/ Scan/ Aspect/ Freeze/ HDR/ Level Meter.

Default: Level Meter.

Menu Operation

Before setting the functions, please make sure the device is connected correctly.

PICTURE

– Brightness –

Adjust the general brightness of the LCD from [0]-[100]. For example, if the user is outside in bright conditions, increase the LCD brightness to make it easier to view.

– Contrast –

Increases or decreases the range between the bright and dark areas of the image. High contrast can reveal detail and depth in the image, and low contrast can make the image appear soft and flat. It can be adjusted from [0]-[100].

– Saturation –

Adjust the color intensity from [0]-[100]. Turn the knob right to increase the color intensity and turn left to decrease it.

– Tint –

It can be adjusted from [0]-[100]. Affect the resulting color mixture’s relative lightness.

– Sharpness Increase or decrease the sharpness of the image. When the image sharpness is insufficient, increase the sharpness to make the image clearer. It can be adjusted from [0]-[100]. – HDR Options: [Off], [HDR10_300], [HDR10_1000], [HDR10_10000], [HLG]. Note: Only available under SDI and HDMI mode. – Color Temp. [6500K], [7500K], [9300K] and [User] mode for optional. Adjust the color temperature to make the image warmer (Yellow) or colder (Blue). Increase the value to make the image be warmer, decrease the value to make the image be colder. User can use this function to strengthen, weaken or balance the image color according requirements. The standard white light color temperature is 6500K. Color Gain/Offset is available only under “User” mode to choose the color value.
MARKER

– Center Marker

Select On, it will appear “+” marker on center of screen.

– Aspect Marker
The Aspect Marker provides various aspect ratios, as the following: [OFF], [2.35:1], [1.85:1], [4:3], [3:2]
– Safety Marker
Used to select and control the size and availability of the safety area. Available typeS are [OFF], [95%], [93%], [90%], [88%], [85%], [80%] preset to choose.
– Marker Color
Select the color of marker displayed on the screen: [Red], [Green], [Blue], [White], [Black]. – Grid Options: [ON], [OFF]. – Aspect Mat. When activated, it can be selected from 1-7 (Step value is 1).

– Thickness Adjust the thickness of all the marker lines from [2], [4], [6], [8] (Step value is 2).

FUNCTION

Function

| Scan| Aspect, Pixel To Pixel, Zoom
---|---|---
Aspect| Full, 1.85:1, 2.35:1, 4:3, 3:2
Display Scan| Fullscan, Overscan, Underscan
Check Field| OFF, Mono, Red, Green, Blue
Zoom| X1.5, X2, X3, X4
Freeze| OFF, ON

– Scan –

Use this menu option to choose Scan mode. There are three modes preset:

• Aspect
  Select Aspect under Scan option, then use Aspect option to switch between several aspect ratio setting. For example:
  In 4:3 mode, images are scaled up or down to fill the maximum 4:3 portion of the screen.
  In Full mode, images are scaled to fill the entire screen.

• Pixel to Pixel
  The pixel to pixel is a monitor set to 1:1 pixel mapping with native fixed pixels, which avoids loss of sharpness due to scaling artifacts and normally avoids incorrect aspect ratio due to stretching.

• Zoom
  The image can be enlarged by [X1.5], [X2], [X3], [X4] ratios. To select the [Zoom] under [Scan], choose the times under [Zoom] option which underneath the Check Field option.

Note! Zoom option can ONLY be activated when user select [Zoom] mode under [Scan] function.

– Aspect –

Select the aspect of the image among [Full],[1.85:1], [2.35:1], [4:3], [3:2].

– Display Scan
If the image shows size error, use this setting to zoom in/out pictures automatically when receiving signals. The scan mode can be switched among [Fullscan], [Overscan], [Underscan].
– Check Field
Use the check field modes for monitor calibration or to analyze individual color components of an image. In [Mono] mode, all color is disabled and only a grayscale image is shown. In [Blue], [Green], and [Red] check field modes, only the selected color will be shown.
Note! DSLR is available ONLY under HDMI mode.
– Freeze Activate freeze function to freeze current picture when playing the video.

VGA

– Auto
Select [On], the monitor can automatically adjust the position of the image. Select [Off], users can manually adjust the position of the image.
– Phase
Adjust internal phase sequence difference. Adjustable range: 0-100.
– Clock
Adjust internal oscillation frequency when interference occurs. Adjust this item, the image can be compressed or stretched left or right. Adjustable range: 0-100.
– H-Position
Horizontally adjust the position of the image on the screen. Adjustable range: 0-100.
– V-Position
Vertically adjust the position of the image on the screen. Adjustable range: 0-100.
Note! Only available under VGA mode.

AUDIO

CH12&13, CH14&15

– Volume –

To adjust the volume from [0]-[100] for the built in speaker and earphone jack audio signal.

– Level Meter –

The left side of the on screen meters displays level meters showing audio levels for channels 1 and 2 of the input source. It features peak hold indicators which stay visible for a short time so the user can clearly see the maximum levels reached.
To achieve optimum audio quality, ensure the audio levels do not reach 0. This is the maximum level, meaning that any audio that exceeds this level will be clipped, resulting in distortion. Ideally peak audio levels should fall in the upper end of the green zone. If the peaks enter into the yellow or red zones, the audio is in danger of clipping. – Audio Channel The monitor can receive 16 channels audio from SDI signal. The audio channel can be changed among [CH0&CH1], [CH2&CH3], [CH4&CH5], [CH6&CH7], [CH8&CH9], [CH10&CH11], [CH12&CH13], [CH14&CH15] 2-2-6. SYSTEM

System

Scan / Aspect / Freeze / Level Meter
Reset| OFF, ON

– Language
Switch between [English] and [Chinese].
– OSD Timer
Select the displaying time of the OSD. It has [10s], [20s], [30s] preset to choose.
– OSD Transparency
Select the transparency of the OSD from [Off] [Low] [Middle] [High]
– Image Flip
The monitor support [H], [V], [H/V] three preset Flip modes.

– Auto Backlight
Select On, the Auto Backlight function can be automatically adjusted according to the ambient brightness.
– Back Light
Adjusts the level of the back light level from [0]-[100]. If the back light value is increased, the screen becomes brighter.
– F1 Configuration
Select “F1 Configuration” for setting. Functions: [Level Meter] [Center Marker] [Aspect Marker] [Check Field] [Display Scan] [Scan] [Aspect] [Freeze] [HDR]. Default function: [Level Meter] – Reset
If there is any problem unknown, press to confirm after selected. The monitor will return to default settings.

Parameter

1080p(60/59.94/50/30/29.97/25/24/23.98/24sF/30sF/29.97sF/25sF/23.98sF) 1080i(60/59.94/50)
HD-SDI| 1080p(30/29.97/25/24/23.98/30sf/29.97sf/25sf/24sf/23.98sf) 1080i(60/59.94/50) 720p(60/59.94/50/30/29.97/25/24/23.98)
SD-SDI| 525i(59.94) 625i(50)
HDMI1.4| 2160p(30/29.97/25/24/23.98) 1080p(60/50/30/29.97/25/24/23.98) 1080i(60/50)
Ear Jack| 3.5mm
Environment| Operating

Temperature

| 0℃~50℃
Storage Temperature| -10℃~60℃
General| Dimension (LWD)| 524.8×313.3×44.5mm
Weight| 5.1kg

Accessories

1. 15V DC Adapter  1 piece
2. HDMI A/A cable 1 piece
3. VGA cable  1 piece
4. VIDEO cable  1 piece
5. AUDIO cable 1 piece
6. Base bracket  1 piece

Trouble Shooting

1. Only black-and-white display: Check whether the color saturation and check field are properly setup or not.
2. Power on but no pictures: Check whether the cables of HDMI, and 3G-SDI are correctly connected or not. Please use the standard power adapter coming with the product package. Improper power input may cause damage.
3. Wrong or abnormal colors: Check whether the cables are correctly and properly connected or not. Broken or loose pins of the cables may cause a bad connection.
4. When on the picture shows size error: Press [MENU] [Function] [Aspect] to zoom in/out pictures automatically when receiving HDMI signals
5. Other problems: Please press Menu button and choose [MENU] [System] [Reset] [ON].
6. According to the ISP, the machine cannot function properly: ISP for program upgrades, non-professionals do not use. Please reboot your device if press accidentally!
7. Image Ghosting: If continue to display the same image or words on the screen for a long period of time, part of that image or words may burn into the screen and leave a ghosting image behind. Please understand it ‘s not quality issue but the character of some screen, so no warranty/return/exchange for such situation.
8. Some options cannot be select in the Menu: Some options are available only in a certain signal mode, such HDMI, SDI or VGA. Some options are available only when a certain feature is turned on. For example, Zoom function shall be set after following steps: [Menu] [Function] [Scan] [Zoom] [Exit] [FN] [Zoom].
   Note: Due to constant effort to improve products and product features, specifications may change without priority notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>