MODSTER Mini Blizzard Sender User Manual

MODSTER Mini Blizzard Sender User Manual

Important notes:

This product is not a toy. Incorrect handling can lead to injury and damage. Read the instructions before use, otherwise the manufacturer will not accept any claims for damage.

Safety instructions

• Fly away from people and not over crowds.
• Keep your distance from animals, buildings, heat sources, power lines and substations.
• Keep your distance from obstacles while flying.
• This product is suitable for indoor & outdoor operation (maximum wind force 3).
• A flying drone may cause damage or injury to people due to malfunction interferences.
• Observe national regulations regarding the operation of flying devices.
• Fly only in warm, dry and windless weather conditions.
• Always keep the drone in sight!
• Do not touch the rotating propellers and keep your distance – risk of injury!
• Allow the motor and battery to cool down for at least 20 minutes after each flight to avoid overloading. Do not touch hot parts of the drone.
• Do not look directly into the LEDs – they are very bright and can cause eye damage.

Beginner tip: Practice flying at low altitude for 3 days. Ask an experienced pilot for assistance with your first flights.

This product is suitable for people with a minimum age of 14 years.

Flight preparation

Flight area

Indoors: Avoid the vicinity of obstacles, animals and people.

Outdoor: Sunny and preferably windless weather is preferred preferred.

Always keep the drone in view. Do not fly near power lines, trees, or collections of people.

Do not fly during precipitation, thunderstorms or in windy conditions.

Flying

Make sure that the propellers are correctly mounted and tightened.

1. Switch on the device and place it on a flat surface.
   

2. Switch on the remote control.
   

3. Move the left control stick forward, then back to bind the drone & transmitter.
   

Start method 1:

1. Place the drone on a flat surface. Move the two control sticks to the apparent position. After 2-3 seconds, the LED will flash rapidly. The calibration was successful if the LED lights up constantly after 2-3 seconds.
   

2. Move the two control sticks as shown in the figure to start the motors
   

3. Move the left control stick forward, the drone will take off.
   

Start method 2:

1. Place the drone on a flat surface. Move the two control sticks to the position shown in the picture. After 2-3 seconds, the LED of the drone will flash rapidly. After 2-3 seconds, the LED will be on constantly, the calibration was successful.
   

2. Press the takeoff/landing button and the drone will take off.
   

Landing method 1:

Slowly pull the left stick back until the drone lands. After landing, hold the stick in the rear position for another 2 seconds until the motors stop.

Landing method 2:

Press the takeoff/landing button, the drone will take off by itself and then stop the motors.

Landing method 3:

In case of emergency, e.g. if the drone flies against an obstacle, press the the emergency stop button. The motors will stop immediately and the drone will to the ground. This is an emergency measure to prevent  further damage, but damage may occur in the process.

Control Manual

** 1| Rise and fall| When the left control stick is moved forward or backward, the drone will rise or sink, respectively.|
---|---|---|---
2| turn| When the left control stick is moved to the left or right, the drone rotates|
** 3| forwards backwards| When the right control stick is moved forward or backward, the drone flies forward or backward re- spectively|
4| left and right flying| When the right control stick is moved left or right, the drone flies left or right|
** 5| left and right trim| If the drone drifts sideways press the right stick, the remote control will beep. Now you can use the left/ right control stick to fine-tune the make|
** 6| forwards and backwards trim| If the drone drifts forward or backward, press the right stick, the remote control will beep. Now you can use the forward/backward control stick to fine-tune the make|
**** 7| Headless mode| Pressing and holding the Headless button activates the headless mode, this is signaled by a beep, the 4 LEDs on the drone flash slowly. Pressing the button again for 2 seconds will end the headless mode. In he- adless mode, the pilot does not have to pay attention to the orientation of the drone, it reacts directly in the direction of the control stick movement.| **
** 8| reset| Holding both control sticks in this position will reset the drone. This should only be done on the ground when the drone is positioned on a level surface. After about 3 seconds of rapid flashing, the LED‘s will glow steadily to indicate a successful recalibration. to signal a successful recalibration.|

Flight exercises

1. flight exercise
   Slowly push the left control stick forward until the drone lifts off the ground and hovers. Now slowly pull the left control stick back until it lands again. Repeat this exercise until you get a feel for it
   

2. flight exercise
   When hovering, carefully move the right control stick forward/backward and left/right
   

3. flight exercise
   When the drone is hovering, move the left control stick left/right. Rotate the drone in this way.

3D Flip function

Once you have mastered the basic flight controls, you can go one step further and fly small tricks. Press the 3D button on the upper right corner of the remote control, the remote control will beep. By moving the right stick forward/backward or left/right, the drone will perform a rollover in the corresponding direction.

Reminder:

1. Before flying, place the drone on a flat surface to be sure it will hover smoothly.

2. Flying indoors: Keep your distance from obstacles, animals and people.

3. Flying outdoors: Fly in warm weather with as little wind as possible.
   Warning:

4. Do not fly in bad weather. Heat or cold weather can negatively affect flight v performance and characteristics.

5. Do not fly in strong winds. The drone may veer off course.

Remote control functions and switches

Assembly

Open the battery compartment in the direction of the arrows and insert two fully charged AAA batteries into the battery compartment as shown in the illustration.

Pay attention to the correct polarity!
Empty batteries affect the transmission reliability of the remote control to the drone.

Do not mix empty and full batteries.

Charging the batter

Take the USB charging cable out of the package & insert the Micro USB plug into the designated socket on the battery. Then connect the charging cable to a suitable USB socket (computer socket, mains adapter, power bank). During the charging process, the LED on the red lights up. After the end of the charging process, the LED goes out & the battery is fully charged. (duration approx. 100 minutes)

B attery safety instructions:

• Old and new ones must not be used together.
• Do not charge non-rechargeable batteries.
• Only use the enclosed charger!
• Insert the batteries correctly. Pay attention to polarity.
• Do not short-circuit batteries or rechargeable batteries!
• Only charge rechargeable batteries under adult supervision!
• Never charge batteries unsupervised!
• Charge batteries only on fireproof surfaces and far away from flammable materials.
• Do not overcharge. Dispose of batteries according to the regulations.
• Do not dispose of batteries or rechargeable batteries in a fire

Replace propeller

1. Propellers to be replaced must always be mounted in the correct position. Propellers marked A must be mounted at position A; propellers marked B must be mounted at position B.
2. In flight, propellers A rotate clockwise, propellers B counterclockwise.

Problem solving

replace theRemote control battery
 the binding process between and the drone was not successful|  perform the binding process again again
The drone reacts inaccurately to control|  The battery of the remote control is weak or of poor quality|  Replace the old battery with a new one
 another remote control or WLAN inter- feres with the transmission|  change the flight area
The drone drifts sideways while hovering|  No horizontal position correction| Remote Control and perform the calibration again.

Precautions

1. If the remote control batteries are weak, the range and transmission quality will be poor.
2. Be careful when the drone is powered on – if it malfunctions, the motors may start and cause injury or damage.
3. Do not fly with a damaged drone – repair the unit before the next flight. Otherwise, injury or damage= may occur.
4. Remove the batteries from the remote control after operation.
5. Do not drop the remote control.

Spare Parts

Here you can find available spare parts for the drone:

• Propeller Set 294781
  

• Battery 294782

• Motor set 294783 CW A 294784 CCW B
  

Disclaimer of warranty

• Only for children 14 years and older
• Product contains small parts that can be swallowed
• Keep hands, face, hair and loose clothing away from rotors
• Do not reach into rotating parts
• Always disconnect battery plug and remove battery from model after flight!
• Fly only where it is safe and you do not endanger third parties
• Keep the operating instructions and read them carefully before use.
• We recommend that persons with no knowledge of model flying operate the model under the guidance of an experienced pilot
• Before each flight, test the range of the remote control, as well as the battery charge level and check
• batteries or accumulators in the remote control.

Do not fly…

• near crowds of people,
• towards people or animals,
• in poor visibility,
• in the vicinity of high-voltage power lines or radio masts
• during thunderstorms, in rain, snow or damp conditions.

1. Always keep the aircraft in sight and under control.
2. Always use fully charged batteries.
3. Always turn on model first, then transmitter, and always turn off model first, then transmitter.
4. Do not use the model if it shows visual or mechanical damage.
5. Always check all screw connections and structures for tightness and damage.
6. Never reach into the rotating rotor – risk of injury!
7. Always disconnect and/or remove the flight battery from the model after flight.
8. Always charge the battery outside the model, charge on a non-combustible surface, never store the battery inside the model.

Never charge batteries unattended!
Inform yourself about the legal regulations valid in your country.

App

IOS

Android

Google Play

Add device:

1. turn on the power switch of the device. Go to the settings of your phone and open WIFI. 3.
2. find the device from the WIFI list and click on it until the connection is successful.
3. open the APP and click the launch icon.
4. Click the „Album“ icon to open the real-time interface.
   

Declaration of conformity in accordance with the radio Equipment Directive (RED) 2014/53/EU.

I hereby declare that the product: MODSTER Mini Blizzard Pro
Product number:  294583 ( EAN: 426752712224)

Complies with the essential requirements and the other relevant provisions of the Directive (RED) 2014/53/EU, when used for its intended purpose.

EN 62479:2010
EN 301 489-1 V2.1.1 (2017-02)
EN 301 489-3 V2.2.1 (2017-03)
EN 62311 Version 2008
EN 300 440 V2.1.1 (2017-03)
Rechtiche Informationen:
RoHS 2-Richtlinie 2011/65 /EU;
RoHS – Anderung 2011/65/ EU-Anhang 112015/863
Richtlinie 2012/19/EU Ober Elektro- and Elektronik-Altgerate.

Hersteller / verantwortliche Person: MSG Online GmbH Walter Bittdorfer
Manpfacturer / responsible Person: Wirtschaftspark 9 8530
FaVricant / pffsonnei ispoisable: Deutschlandsberg, Austria

References

• MODSTER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>