Philips MG5730/15 Hair Trimmer User Manual

June 9, 2024
Philips

Philips MG5730/15 Hair Trimmer

Philips-MG5730\(15\)-Hair-Trimmer-product

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

General description

Fig. 1 is mentioned in the following:

  1. Full-size hair trimmer
  2. On/off slide
  3. Socket for small plug
  4. Precision trimmer
  5. Precision shaver (MG5740, MG5735, MG5730 only)
  6. Nose trimmer
  7. Hair comb 3/8in. (9mm)
  8. Hair comb 15/32in. (12mm)
  9. Hair comb 21/32in. (16mm)
  10. Stubble comb 3/64in. (1mm)
  11. Stubble comb 5/64in. (2mm)
  12. Adjustable comb (3-7mm)
  13. Body comb 1/8in. (3mm) (MG5740, MG5735, MG5730 only)
  14. Body comb 3/16in. (5mm) (MG5740 only)
  15. Supply unit
  16. Small plug
  17. Cleaning brush
  18. Pouch

Note : The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance.

Important safety information

Read this important information carefully before you use the appliance and its accessories and save it for future reference. The accessories supplied may vary for different products.

Danger

Keep the supply unit dry.

Warning

  • To charge the battery, only use the detachable supply unit (A00390) provided with the appliance.
  • The supply unit contains a transformer. Do not cut off the supply unit to replace it with another plug, as this causes a hazardous situation.
  • This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Always unplug the appliance before you clean it under the tap.
  • Always check the appliance before you use it. Do not use the appliance if it is damaged, as this may cause injury. Always replace a damaged part with one of the original types.
  • Do not open the appliance to replace the rechargeable battery.

Caution

  • Never immerse the charging stand in water and do not rinse it under the tap.
  • Never immerse the appliance in water. Do not use the appliance in the bath or shower.
  • Never use water hotter than 60°C to rinse the appliance.
  • Only use this appliance for its intended purpose as shown in the user manual.
  • For hygienic reasons, the appliance should only be used by one person.
  • Do not use the supply unit in or near wall sockets that contain an electric air freshener to prevent irreparable damage to the supply unit.
  • Never use compressed air, scouring pads, abrasive cleaning agents, or aggressive liquids such as petrol or acetone to clean the appliance.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

General

  • This appliance can be safely cleaned under the tap.
  • The supply unit is suitable for mains voltages ranging from 100 to 240 volts.
  • The supply unit transforms 100-240 volts to a safe low voltage of fewer than 24 volts.
  • Maximum noise level: Lc = 69 dB(A)

Charging

Charging with the supply unit

When the appliance has been charged for 16 hours, it has a cordless operating time of up to 80 minutes.

  1. Make sure the appliance is switched off.
  2. Insert the small plug into the appliance and put the supply unit in the wall socket.
  3. After charging, remove the supply unit from the wall outlet and pull the small plug out of the appliance.

Using the appliance

  • Note: This appliance can only be used without a cord.
  • Note: Switch off and clean the appliance after each use.
Detaching and attaching cutting elements

Philips-MG5730\(15\)-Hair-Trimmer-FIG-3

  1. To detach a cutting element, push upwards against the teeth of the cutting element and take it off the handle.
  2. To attach a cutting element, insert the lug of the cutting element into the guiding slot at the front and push the back of the cutting element onto the appliance (‘click’).
Detaching the precision shaver and nose trimmer
  1. Place your finger on the arrow at the back of the attachment and push it off the handle in the direction of the arrow.
Attaching and detaching combs

Philips-MG5730\(15\)-Hair-Trimmer-FIG-5

  1. To attach any type of guard onto a cutting element, slide the front part of the guard onto the teeth of the cutting element. Then push down the center of the guard with your fingers or the palm of your hand (‘click’).
  2. To detach any type of comb from the cutting element, carefully pull its back part off the appliance and then slide it off the cutting element.

Note : When trimming for the first time, start by using the comb with the maximum trimming length setting to familiarize yourself with the appliance.

Switching the appliance on and off
  • To switch on the appliance, push the on/off slide upwards.
  • To switch off the appliance, push the on/off slide downwards.
Attachments for use on beard

Full-size hair trimmer

Use the full-size hair trimmer without a comb to trim hair close to the skin (to a length of 1/32in (0.5mm) or to create clean lines around your beard, neck, and sideburns.

  1. To trim hair close to the skin, place the flat side of the cutting element against your skin and make strokes against the direction of hair growth.
  2. For contouring, hold the cutting element perpendicular to the skin and move it upwards or downwards with gentle pressure.Philips-MG5730\(15\)-Hair-Trimmer-FIG-8

Beard combs

Attach a beard comb to the full-size hair trimmer to trim your beard and mustache evenly. The appliance comes with 5 beard combs. The hair length settings are indicated on the combs. The settings correspond to the remaining hair length after trimming.

Comb inch mm
Stubble comb 3/64in. 1mm

Stubble comb

Adjustable beard comb

| 5/64in.

1/8in.- 9/32in.

| 2mm

3mm-7mm

  1. Attach the comb to the full-size hair trimmer.
  2. Adjustable comb: Push the length selector to the left or right to select the desired hair length setting.
  3. To trim the most effective way, move the comb against the direction of hair growth. Make sure the surface of the comb always stays in contact with the skin.
Attachments for use on the body
  • Use the green body combs to trim body hair.
  • When you trim for the first time, use the 5mm/3/16in. body comb to familiarize yourself with the appliance.
  • Make sure hair is clean and dry as wet hair tends to stick to the body.
  • When trimming sensitive areas, always use a body comb.
  • Since all hairs do not grow in the same direction, you may want to try different trimming positions (i.e. upwards, downwards, or across). Practice is best for optimum results.
  • Always make smooth and gentle movements and be sure the surface of the comb always stays in contact with your skin.
  • When too many hairs have accumulated on the appliance, blow the hairs out before use, for best trimming results.

Body combs

Attach a body comb to the full-size hair trimmer to trim hairs below the neckline. The appliance comes with 2 body combs. The hair length settings are indicated on the combs. The settings correspond to the remaining hair length after trimming.

Comb inch mm
Body comb (green) 1/8in. 3mm
Body comb (green) 3/16in. 5mm
  1. Attach a body comb to the full-size hair trimmer.
  2. To trim in the most effective way, stretch the skin with your free hand and move the comb against the direction of hair growth. Make sure the surface of the comb always stays in contact with the skin.

Philips-MG5730\(15\)-Hair-Trimmer-FIG-10

Attachments for use on head

Full-size hair trimmer

Use the full-size hair trimmer without a comb to clip the hair on your head very close to the skin (1/32in (0.5mm) or to contour the neckline and area around the ears.

  1. To contour the hairline around the ears, comb the hair ends over the ears.
  2. Tilt the appliance in such a way that only one edge of the cutter blades touches the hair ends when you shape the contours around the ears.
  3. To contour the nape of the neck or sideburns, turn the appliance and make downward strokes.Philips-MG5730\(15\)-Hair-Trimmer-FIG-11
  4. Move the appliance slowly and smoothly following the natural hairline.

Hair combs

Attach a hair comb to the full-size hair trimmer to evenly trim the hairs on your head. The appliance comes with 3 hair combs. The hair length settings are indicated on the combs. The settings correspond to the remaining hair length after trimming.

Comb inch mm
Hair comb 3/8in. 9mm
Hair comb 15/32in. 12mm
Hair comb 21/32in. 16mm
  1. Attach a comb to the full-size hair trimmer.
  2. Move the trimmer slowly over the crown from different directions to achieve an even result. Make sure the surface of the comb always stays in contact with the skin.
    • Always move the trimmer against the direction of hair growth. Press lightly.
    • Make overlapping passes over the head to ensure that all hair that should be cut has been cut.
Precision attachments for use on the face

Precision trimmer

Use the precision trimmer to create fine lines and contours around your facial style, close to the skin (to a length of 1/32in./0.5mm).

  1. Hold the precision trimming head perpendicular to the skin and move the trimming head upwards or downwards with gentle pressure.
Nose trimmer

Use the nose trimmer to trim your nose hair and ear hair.

  • Make sure nasal passages are clean. Make sure outer ear channels are clean and free from wax.
  • Do not insert the tip more than 3/16in./5mm.
  • Always clean the attachment after each use.

Trimming nose hair

  1. Gently move the tip in and out of the nose while turning it around to remove unwanted hairs.

Philips-MG5730\(15\)-Hair-Trimmer-FIG-14

Trimming ear hair

  1. Slowly move the tip around the ear to remove hairs that stick out beyond the rim of the ear.
  2. Gently move the tip in and out of the outer ear channel to remove unwanted hairs.

Philips-MG5730\(15\)-Hair-Trimmer-FIG-15

Precision shaver

Use the precision shaver after trimming, to shave unwanted hairs on cheeks, chin, and along the beard with precision. Make sure to pre-trim your beard first, with the full-size hair trimmer without a comb, to obtain the best result.

Note : Use the precision shaver to remove the remaining hairs and detail your beard style. It is not suitable for a full-face shave.

  1. Gently press the precision shaver onto the skin and shave along contoured edges to remove any unwanted hairs.

Cleaning

  • Never use scouring pads, abrasive cleaning agents, or aggressive liquids such as gasoline or acetone to clean the product.
  • Never dry the trimmer teeth with a towel or tissue, as this may damage the trimmer teeth.
After every use: cleaning under the tap
  1. Turn off the appliance and disconnect it from the wall socket.
  2. Remove any comb or cutting element from the appliance.
  3. Rinse the hair chamber under a warm tap.
  4. Clean the cutting element and comb under a warm tap.
  5. Carefully shake off excess water and let all parts air dry completely.
Thorough cleaning
  1. Turn off the appliance and disconnect it from the wall socket.
  2. Wipe the handle of the appliance with a dry cloth.
  3. Remove any comb or cutting element from the appliance.
  4. Remove any hairs that have accumulated in the hair chamber with the cleaning brush supplied.
  5. Remove any hairs that have accumulated in the cutting elements and/or combs with the cleaning brush supplied.
  6. Clean the cutting elements under a warm tap.
  7. Clean the combs under a warm tap.
  8. Carefully shake off excess water and let all parts air dry completely.
Cleaning the nose trimmer

Clean the nose trimmer immediately after use and when a lot of hair or dirt has accumulated on the nose trimmer head.

  1. Rinse the nose trimmer head with hot water.

  2. Turn on the appliance and rinse the nose trimmer head once more to remove any remaining hairs. Then turn off the appliance again.
    For a thorough clean, immerse the nose trimmer head in a bowl with warm water for a few minutes, and then turn on the appliance to remove stubborn hair/debris.

  3. Carefully shake off excess water and let all parts air dry completely.

Cleaning the precision shaver
  1. Hold the precision shaver at the grooves on each side and pull the top part off the bottom part.

  2. Blow and/or shake out any hair that has accumulated inside the precision shaver.
    Do not use the cleaning brush to remove hairs from the shaving foil.

  3. Clean the top part of the precision shaver under a warm tap.

  4. Carefully shake off excess water and let all parts air dry completely.

  5. Reattach the top part onto the bottom part of the precision shaver.

Storage

Store the appliance in the pouch supplied.

Note: Make sure the appliance is dry before you store it in the pouch.

Ordering accessories

To buy accessories or spare parts, visit www.shop.philips.com/service or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).

Recycling

  • This symbol means that this product shall not be disposed of with normal household waste (2012/19/EU).
  • This symbol means that this product contains a built-in rechargeable battery which shall not be disposed of with normal household waste (2006/66/EC). Please take your product to an official collection point or a Philips service center to have a professional remove the rechargeable battery.
  • Follow your country’s rules for the separate collection of electrical and electronic products and rechargeable batteries. Correct disposal helps prevent negative consequences for the environment and human health.

Removing the rechargeable battery

Only remove the rechargeable battery when you discard the product. Before you remove the battery, make sure that the product is disconnected from the wall socket and that the battery is completely empty.

Take any necessary safety precautions when you handle tools to open the product and when you dispose of the rechargeable battery.

  1. Check if there are screws in the back or front of the appliance. If so, remove them.
  2. Remove the back and/or front panel of the appliance with a screwdriver. If necessary, also remove additional screws and/or parts until you see the printed circuit board with the rechargeable battery.
  3. Remove the rechargeable battery.

Warranty and support

If you need information or support, please visit www.philips.com/support or read the international warranty leaflet.

Warranty Restrictions: Cutting units are not covered by the terms of the international warranty because they are subject to wear

FAQ’s

What is mg5730’s warranty period?

Global voltage and a four-year warranty.

What do the Philips trimmer’s numbers mean?

The combs’ numbers correspond to the length of hair that was cut afterward.

Can we use water to clean a Philips trimmer?

Only waterproof Philips groomers and trimmers can be rinsed.

The Philips 5000 series is water resistant.

With its 80-minute runtime, DualCut technology, and 11 styling tools, this Philips Series 5000 Multigroom Trimmer helps you trim and style your face, hair, and body. The trimmer’s complete waterproofness makes it ideal for use in the shower and easy to clean by running it under the faucet.

When is my Philips trimmer fully charged, and how do I know?

Your device’s charging indicator will begin to blink when the groomer is charging.

What is the trimmer’s length setting?

Trim from 0.5 mm to 10 mm in length.

Can the Philips trimmer’s battery be changed?

Your Philips Shaver has a unique built-in battery included. Never attempt to change the battery yourself.

How is the Philips MG5730 charged?

Philips MG5730/33 Series 5000 4.3V Power AC Adapter Charger for 11-in-1 Shaver.

How is a Philips trimmer maintained?

To activate the pop-up trimmer, slide the trimmer release lever downward.

How can I tell whether my Philips Series 5000 has enough juice?

When the battery is low, the lowest bar on other shavers, such as the Philips 5000X Shaver, blinks orange. While charging, it will flash white. It will remain lighted for 30 minutes once completely charged.

Will the Philips 5000 work in the shower?

The Philips Series 5000 electric shavers can be used dry, with shaving foam, or in the shower.

Can you shave in the shower using a Philips device?

The Philips OneBlade works well on both dry and wet skin, as well as when using shaving foam or gel. You may use your OneBlade in the shower as well because of its waterproof handle.

What purpose does a number serve in a trimmer?

Depending on the brand, guards range from 0 to 8 (and occasionally up to 10). Since many of the lower guard numbers are utilized in fades, the shorter the guard number, the shorter the hair will be. If you request a fade, you’ll get bonus points for knowing which guard number you want to fade from and into.

How should my Philips trimmer be adjusted?

To change length settings, your Philips Groomer can have a different style of a sliding button. The button for these versions can be found either on the comb itself or on the device’s handle. Simply push the button and slide it up or down to alter the settings.

Can a trimmer be used without a comb?

Avoid using the trimmer head on sensitive areas, such as the pubic region, without the comb attachment. Instead, think of the trimmer without the comb as trimming close to the skin. You can use your groomer to trim and shave the body hair on your chest, genital area, and other areas below the neckline.

Download this PDF Link:Philips MG5730/15 Hair Trimmer User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals