REELCRAFT 5000 Series Spring Driven Hose Reels

SAFETY

1. Do not use reel at higher pressures or temperatures than listed on the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.

Dimensions

INSTALLATION

A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and binding.

MOUNTING

The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the reel at the desired position and replace the screws.

NOTE: For proper installation in wall mount applications, ensure reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.

LUBRICATION

Hose reel spring and bearings are factory lubricated and require no further lubrication.

REPLACING HOSE

1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.

ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is obtained.

REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may void your warranty. Remove all spring tension before beginning disassembly process.

Item #| Part #| # Req.| Description| Item #| Part #| # Req.| Description| Item

| Part #| # Req.| Description

---|---|---|---|---|---|---|---|---|---|---|---
1| 300031| 2| 1” Snap Ring| 11| S500107| 1| Guide Arm Assembly| 21| S400012| 1| Latch Bushing
2| 300034| 2| Spacing Washer| 12| 500101| 1| Base Assembly| 22| S400018| 1| Latch Spring
3| S295-102| 3| 1/4-10 x 5/8”

Self Tapping Screw

| 15| S261360| 1| Spring Case Stud| 24| 400020| 1| O-ring
4| 260022| 1| Sheave Flange| 16| 300006| 1| 3/8-16 x 1/2” Set Screw| 25| S400109| 1| Latch Plate Assembly
5| 500006| 1| Sheave Disk| 17| S500103| 1| Spring Case & Hub Assembly| 26| 300035| 1| 10-32 x 1” Machine Screw
6| S500019| 1| Latch Cam| 18| S82-15| 8| 10-32 x 3/8” Nyloc Nut| 27| 3-117440| 1| U-bolt Hose Clamp
7| S260648| 2| Spring Arbor| 19| S400021| 1| Latch Plate Bumper| 28| 261650-1| 2| 1/4-20 Nyloc Nut
8| 300002| 7| 10-32 x 1/2” Machine Screw| 20| S32-136| 1| 10-24 x 3/8”Self Tapping Screw| 30| 602305| 1| Main Shaft
Item #| Description| # Req.| 5400 OMP| 5420 OMP| 5600 OMP| 5620 OMP| 5630 OMP
---|---|---|---|---|---|---|---
9| Bumper Stop Assembly| 1| None| 1-HR1004-A| None| 1-HR1004-3| 1-HR1004-3
10| Hose Assembly| 1| None| 13-260043| None| 15-260043| 16-260043
14| Drive Spring| 1| S505740| S505740| S505740| S503755| S505740
31| Swivel Assembly| 1| S600886| 602032| 602032| 602032| 602032
32| Swivel Union| 1| None| S257-25| S257-25| S257-25| S257-25
Hose I.D. and Length| None| 1/4” x 20’| None| 3/8” x 20’| 3/8” x 30’
Reel Inlet Connection| 3/8” F.P.T.| 3/8” F.P.T.| 3/8” F.P.T.| 3/8” F.P.T.| 3/8” F.P.T.
Max. Operating Pressure| 3000 P.S.I.| 2750 P.S.I.| 3000 P.S.I.| 2600 P.S.I.| 2600 P.S.I.
Max. Operating Temperature| 210 °F| 210 °F| 210 °F| 210 °F| 210 °F

References

• Reelcraft Industries - Hose, Cord, and Cable Reels

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>