sygonix 2373341 Rechargeable Light Bar with Touch Sensor Instruction Manual
- June 4, 2024
- Sygonix
Table of Contents
2373341 Rechargeable Light Bar with Touch Sensor
Instruction Manualhttp://www.conrad.com/downloads
Intended use
The product is a rechargeable LED light bar with a touch sensor control. It
comes with a base that can be attached to a magnetic surface or mounted using
the included adhesive or screw.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product
may be damaged.
Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the
product.
Read the operating instructions carefully and store them in a safe place. Make
this product available to third parties only together with the operating
instructions.
All company names and product names are trademarks of their respective owners.
All rights reserved.
Delivery contents
| ■ Product | ■ Double-sided mounting tape |
|---|---|
| ■ Micro USB to USB-A charging cable | ■ 1x mounting screw |
| ■ Magnetic mount | ■ Operating instructions |
Latest product information
Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.
Description of symbols
The symbol with the exclamation mark in the triangle is used to indicate
important information in this document. Always read this information
carefully.
This product is constructed according to protection class III.
Safety instructions
Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.
5.1 General
- The product is not a toy. Keep it out of the reach of children and pets.
- Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
- If you have questions that remain unanswered by this information product, contact our technical support service or other technical personnel.
5.2 Handling
-
If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. The safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses. -
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
-
Consult an expert when in doubt about the operation, safety or connection of the appliance.
5.3 Operating environment
- Do not place the product under any mechanical stress.
- Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam, and solvents.
- Protect the product from high humidity and moisture.
- Protect the product from direct sunlight.
5.4 Li-ion battery
- Never damage the rechargeable battery. Damaging the casing of the rechargeable battery might cause an explosion or a fire!
- Never short-circuit the contacts of the rechargeable battery. Do not throw the battery or the product into the fire. There is a danger of fire and explosion!
- Charge the rechargeable battery regularly, even if you do are not using the product. Due to the rechargeable battery technology being used, you do not need to discharge the rechargeable battery first.
- Never charge the rechargeable battery of the product unattended.
- When charging, place the product on a surface that is not heat-sensitive. It is normal that a certain amount of heat is generated during charging.
5.5 LED light
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
Product Overview
- Touch sensor: power/brightness
- LED light
- DC 5V 1A charging port/status light
Charging the battery
-
Connect one end of the included cable to the microUSB DC 5V 1A port on the product.
-
Connect the other end of the charging cable to a suitable USB-A power source (5 V/DC, min. 1 A) to start charging.
****LED red: charging in progress.
****LED green: fully charged. -
Disconnect the product from the power supply when the battery is fully charged.
Mounting
You can mount the product using the included screws or double-sided adhesive
tape.
8.1 Screws
When penetrating the surface e.g. drilling or inserting fasteners, make sure
no cables or pipes are damaged. Inadvertently penetrating electric cables
causes the life-threatening danger of an electric shock!
8.2 Adhesive tape
- Make sure the surface is clean, flat, smooth, and non-porous.
- The adhesive tape should be positioned correctly on the first attempt as it cannot be reused.
Operation
- Touch the sensor to switch the power ON/OFF.
- Touch and hold the sensor to increase/decrease the brightness.
Cleaning and care
NOTICE! Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause damage to the housing and malfunction.
- Disconnect the charging cable.
- Clean the product with a dry, fiber-free cloth.
Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed
of as unsorted municipal waste at the end of its service life.
Owners of WEEE shall dispose of it separately from unsorted municipal waste.
Spent batteries and accumulators, which are not enclosed by the WEEE, as well
as lamps that can be removed from the WEEE in a non-destructive manner, must
be removed by end users from the WEEE in a non-destructive manner before it is
handed over to a collection point.\
Distributors of electrical and electronic equipment are legally obliged to provide free takeback of waste. Conrad provides the following return options free of charge (more details on our website):
- in our Conrad offices
- at the Conrad collection points
- at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be
disposed of.
It should be noted that different obligations about the return or recycling of
WEEE may apply in countries outside of Germany.
12 Technical data
Input ………………………………………. Micro-USB: 5 V/DC max. 1 A
Power consumption …………………… 2.5 W
Power supply …………………………… 1x 3.7 V 2000 mAh 7.4 Wh Li-ion, type 18650 (non-
removable)
Protection class………………………… III
Battery recharge time ………………… approx. 3.5 hrs
Runtime …………………………………… approx. 4 hrs
Battery protection ……………………… Discharge, overcharge
Brightness………………………………… Max. 160 lm
LED…………………………………………. Lifetime: 15000 hrs, dimmable, 18 pcs, non-removable
Color temperature……………………. 6500 K (cool white)
Operating temperature ……………… -20 to +45 °C
Operating humidity …………………… 20 – 85 % RH
Storage temperature …………………. -20 to +50 °C
Storage humidity ………………………. 20 – 85 % RH
Dimensions (Ø x H) ………………….. 22 x 305 mm
Weight (approx.) ………………………. 140 g
This product contains a light source of energy efficiency class G.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g.
photocopying, microfilming or the capture in electronic data processing
systems) requires prior written approval from the editor. Reprinting, also in
part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2373341_V3_0322_dh_mh_en 264075403 I2/O3 en
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>