EVOLVEO CAM-NL4 Baby Monitor User Manual
- June 9, 2024
- Evolveo
Table of Contents
- WARNING
- PACKAGING CONTENT
- CAMERA
- MONITOR
- GETTING STARTED
- CAMERA SETTINGS
- SOUND DETECTION
- HEAT ALARM
- LULLABIES
- SLEEP MODE
- FEEDING
- DATE / TIME
- SETTINGS
- EXPLANATION OF ICONS
- FREQUENTLY ASKED QUESTIONS
- Disposal
- DECLARATION OF CONFORMITY
- PRODUCT PARAMETER
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EVOLVEO CAM-NL4 Baby Monitor User Manual
WARNING
Improper use of the product can lead to safety hazards. We therefore strongly recommend that you read the following instructions before using the product.
- Keep the cord(s) out of the reach of children (at least 1 metre away).
- In the event of a MISTAKE, please contact the nearest service centre.
- Use ONLY original adapters. Using non-original cables and adapters can damage the device.
- If you are not using the adapter(s), unplug it(them).
- Check your child’s activities regularly as this product is not intended for supervision, but to assist in supervision.
PACKAGING CONTENT
CAMERA
MONITOR
-
VOX: eavesdropping mode, the camera is switched on for the set standby time and it is possible to monitor the events in front of the camera.
-
Camera switch: Camera switching, if 2 or more cameras are connected, you can switch between cameras by repeatedly pressing.
-
Volume/Brightness: Press to adjust the monitor volume or brightness using the left/right and up/down arrows.
-
Power/Sleep button: Long press to turn the monitor on/off; short press to turn the screen on/off.
-
LED panel volume level: the level displays the volume and intensity of the sound detected by the camera. Blue > low, orange > medium, red > high.
-
Menu/Back: Press the button to enter the menu page or press the Back button.
-
Left: Press the button to move the camera to the left or change the selection to the left.
-
Right: Press the button to move the camera to the right or change the selection to the right.
-
Zoom/OK: Press the button to zoom in/out or to confirm the selection.
-
Up: Press the button to tilt the camera up or change the selection upwards.
-
Down: Press the button to tilt the camera downwards or change the selection downwards.
-
Mluvte: Press the button to talk to the child.
-
Charging indicator: lights yellow while the monitor is charging.
-
Performance indicator: The green light will come on when it is connected to electricity.
-
Mikrofon
-
Reset hole
-
USB-C power connector
-
Tilting antenna
-
Support stand
-
Speaker
-
Battery compartment
Remark :
- If you perform a RESET using the pin, the monitor will be forcibly turned off.
- Only replace the battery with an original or identical battery with identical specifications.
Camera
Press the LED button(11) to switch on the lamp, press it repeatedly to change the colors. Hold to start the cycle mode. Press the +/-(12/13) button to change the intensity of the LED lighting. Press the lullaby button (14) to start one of the melodies, press again to change the melody. Hold to switch off the melody. Press the +/-(12/13) button to change the melody volume.
GETTING STARTED
Step 1 :
- Connect the camera to the adapter.
- Plug the mains adapter into a socket.
Remark : Place the camera away from the child (at least 1m).
Step 2 :
- Connect the monitor to the adapter.
- Plug the mains adapter into a socket.
- Long press the power button to turn on the monitor, and then the monitoring interface is displayed.
Remark : The monitor takes about 4 hours to fully charge and the battery life is up to 5 hours.
CAMERA SETTINGS
Warning : The camera and monitor have already been paired. This function is used to add new cameras to the monitor or to reset the monitor.
SOUND DETECTION
Explanation :
There are four levels of sound detection: l (78 dB), ll (65 dB) lll (60 dB)
and OFF. l means that sound can be detected when it reaches 78 dB, and so on
for ll and lll.
HEAT ALARM
LULLABIES
SLEEP MODE
Explanation :
This function is used to extend the monitor’s operating time by turning off
the screen.
Step 1:
Remark :
The screen will automatically light up if an audible or temperature alarm
occurs.
FEEDING
DATE / TIME
SETTINGS
EXPLANATION OF ICONS
1. Status bar icons
2. Notification of lcons
Explanation : You can open the Live-Video-Loop function by briefly
pressing the
buttons on until appears in the status bar. When Live-Video-Loop is enabled,
the connected cameras automatically switch every 10 seconds. And if an
audible/temperature alarm occurs, the camera switch function is temporarily
suspended.
FREQUENTLY ASKED QUESTIONS
Q1. Why couldn’t I connect the camera to the monitor?
-
Make sure the power adapter is firmly connected to the camera and the power outlet.
-
Make sure the camera and monitor are at an effective distance.
Q2. Why is the live video so blurry?
- Make sure there is no obstruction on the camera lens.
Q3. Why was the monitor making noise?
- Camera and monitor may be too close. Place them at a greater distance.
Q4. Can I hear my baby if I turn off the screen?
- Yes. You should enable the Sound Detection feature, which wakes up the screen and triggers an audible alarm if a loud sound is detected.
Q5. Why is the picture black and white?
- Night vision mode is activated when the camera is operating in a dark environment (brightness < 5 lux).
The warranty does NOT cover:
– using the device for purposes other than those for which it is intended,
– installing firmware other than that installed on the device.
– electrical or mechanical damage caused by improper use.
– damage caused by natural influences such as water, fire, static electricity, power fluctuations, etc.
– damage caused by repairs carried out by an unqualified person.
– illegible serial number
– battery capacity will decrease after 6 months of use (6 month battery life guarantee)
Disposal
The crossed-out container symbol on the product, in the accompanying documentation or on the packaging means that all electrical and electronic equipment, batteries and accumulators in the European Union must be disposed of as separated waste at the end of their life. These products must not be disposed of as unsorted municipal waste.
DECLARATION OF CONFORMITY
Abacus Electric, s.r.o. hereby declares that the EVOLVEO Baby Monitor NL4 meets the requirements of the standards and regulations applicable to this type of equipment.
The full text of the Declaration of Conformity can be found at http://ftp.evolveo.com/ce/.
Importer
Abacus Electric, s.r.o. Planá 2, 370 01, Czech Republic
Producer
Naxya Limited
No. 5, 17/F, Strand 50, 50 Bonham Strand, Sheung Wan, Hongkong
Made in China
Copyright © Abacus Electric, s.r.o.
www.evolveo.com
www.facebook.com/EvolveoCZ
All rights reserved. Product appearance and technical specifications are subject to change without notice.
PRODUCT PARAMETER
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>